Lettura libera · account gratuito per contribuireErede di Anticars (2000)

BMW Serie 7 E32

1986–1994 · 5 difetti documentati · 4 mercati
Anno modello
MercatoTuttiNA
RichiamoCriticoMotoreNA

Sistema di alimentazione

Su alcuni veicoli 318I, 318IC, 318IS, 325IC, 325IS, 325IX, 525I, 535I, 735I e 735IL, il tubo di alimentazione del carburante può indurirsi e "deformarsi" nel tempo a causa delle temperature del vano motore. Se si verifica questa "deformazione", è possibile che si verifichino trafilamenti tra il tubo e il raccordo, poiché la fascetta potrebbe non esercitare una forza di tenuta sufficiente a compensare l'indurimento del tubo. La fuoriuscita di carburante, in presenza di una fonte di accensione, potrebbe causare un incendio nel vano motore. Correzione: i tubi di alimentazione del carburante e le relative fascette saranno sostituiti con componenti di un nuovo modello.

Transport Canada30 mag 19941994096Anni modello 1989–1993Tradotto automaticamente · originale: ingleseVedi dettagli →
RichiamoCriticoMotoreNA

Sistema di alimentazione, benzina: Erogazione: Tubi flessibili, tubazioni e raccordi

Con il tempo, i tubi di alimentazione del carburante possono indurirsi e "fissarsi" in posizione, causando una perdita di carburante nel punto di collegamento tra il tubo e il raccordo del motore. La fascetta utilizzata per fissare il tubo al raccordo non è in grado di compensare l'indurimento del tubo di alimentazione del carburante.

NHTSA · Stati Uniti11 apr 199494V066000Anni modello 1989–1993Tradotto automaticamente · originale: ingleseVedi dettagli →
RichiamoModeratoMotoreNA

Engine and engine cooling:Cooling system

Vehicle description: Passenger vehicles. A malfunction or failure of a coolant system component, such as a thermostat, water pump, or fan belt, can result in significantly increased coolant temperature and system pressure. If the indications of a critical overheating condition is not noticed by the driver, it is possible that damage to, or failure of, a coolant system component could occur.

NHTSA · Stati Uniti4 ago 199898V178000Anni modello 1988–1993Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoMotoreNA

Engine

On certain 318IC, 318IS, 318TI, 325I, 325IC, 325IS, 525I, 525IT, 530I, 530IT, 540I, 740I, 740IL, 840CI and M3, the cruise control and throttle cable are attached to the same throttle valve actuating lever at the throttle housing. It is possible that the plastic bushing on either cable could break causing the outer cable housing to separate from the bushing. Throttle pedal application without cruise control engagement could cause the outer tube to catch on the edge of the broken bushing resulting in the throttle valve remaining partially open. If this were to occur, the car might not decelerate as expected and a crash could occut. Correction: A spring clip will be installed on the outer tube of each cable to prevent dislodgment from the bushing.

Transport Canada9 ott 19971997173Anni modello 1993Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoMotoreNA

Vehicle speed control

The cruise control and throttle cables are attached to the same throttle valve actuating lever at the throttle housing. It is possible that the plastic bushing on either cable could break due to environmental influences coupled with vibration. If the bushing breaks, the outer cable housing can separate from the bushing. In this case, during application of the throttle pedal without cruise control being engaged, the outer tube could catch on the edge of the broken bushing.

NHTSA · Stati Uniti19 ago 199797V131000Anni modello 1993Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoMotoreNA

Engine

On certain 740IA and 740ILA vehicles, the inner throttle cable could break due to a smaller than specification bend in the cable tube. If this were to occur, throttle control would be lost and the engine would return to or remain at idle. Correction: Throttle cable will be replaced with one meeting BMW specifications.

Transport Canada25 apr 19941994081Anni modello 1993Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoMotoreNA

Vehicle speed control:Cables

The throttle cable's tube (outer casing) contains a bend that leads to increased loading of the inner cable, causing it to break.

NHTSA · Stati Uniti3 gen 199494V022000Anni modello 1993Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoMotoreNA

Engine

On certain 535I, 535IA, 735IA, 735ILA vehicles, the nut which secures the throttle valve shaft may not have been tightened with sufficient torque. If the nut were to loosen, it is possible that movement of the throttle valve might be impaired. If this should occur, the vehicle might not decelerate as expected after the gas pedal is released and loos of vehicle control could result. Correction: Vehicles will be inspected and affected throttle housings with undertorqued throttle valve retaining nuts will be replaced.

Transport Canada13 ott 19921992129Anni modello 1991Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoMotoreNA

Vehicle speed control

Some of these vehicles are equipped with a throttle housing on which the throttle valve shaft retaining nut was not sufficiently tightened.

NHTSA · Stati Uniti10 lug 199292V101000Anni modello 1991Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoMotoreNA

Emissions

Certain 750IL vehicles fail to comply with the requirements of CMVSS 1103 - Exhaust Emissions.

Transport Canada2 mag 19891989063Anni modello 1988–1989Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoMotoreNA

Emissions

Certain 750IL vehicles fail to comply with the requirements of CMVSS 1103 - Exhaust Emissions

Transport Canada2 mag 19891989062Anni modello 1988–1989Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoMotoreNA

Engine

On certain 750IL vehicles, during the assembly process, the gas pedal may not have been properly attached to the floor pan. If the gas pedal is operated in a rough or erratice manner, it may become stuck between the gas pedal stop (on the floor pan) and the carpeting on the transmission tunnel. If this occurs, the pedal might not return fully to the idle position when the driver's foot is removed and loss of control could result. Application of the brake pedal will close the throttle on this model of vehicle. Correction: Accelerator pedal will be inspected and tightened to the floor is required. Also, a modified pedal stop will be installed.

Transport Canada6 apr 19891989046Anni modello 1988–1989Mostrato in inglese originale · traduzione in attesaVedi dettagli →

Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).