On certain 318I, 318IS, 325I, 325IS, 525I, 525IT, 535I, 735I, 735IL, 750IL, 850I and M5, the locking tab for the airbag contact ring in the steering wheel assembly could break without warning. If this happens it is possible that the contact ring wiring could break. This would cause the readiness indicator lamp ("SRS" or "AIRBAG") to illuminate and in such a case the airbag would not be available for deployment in a frontal impact. Correction: Locking tab will be replaced with one of a different design.
Transport Canada7 ott 19961996159Anni modello 1991–1992Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Su alcuni veicoli 318I, 318IC, 318IS, 325IC, 325IS, 325IX, 525I, 535I, 735I e 735IL, il tubo di alimentazione del carburante può indurirsi e "deformarsi" nel tempo a causa delle temperature del vano motore. Se si verifica questa "deformazione", è possibile che si verifichino trafilamenti tra il tubo e il raccordo, poiché la fascetta potrebbe non esercitare una forza di tenuta sufficiente a compensare l'indurimento del tubo. La fuoriuscita di carburante, in presenza di una fonte di accensione, potrebbe causare un incendio nel vano motore. Correzione: i tubi di alimentazione del carburante e le relative fascette saranno sostituiti con componenti di un nuovo modello.
Transport Canada30 mag 19941994096Anni modello 1989–1993Tradotto automaticamente · originale: ingleseVedi dettagli →
Con il tempo, i tubi di alimentazione del carburante possono indurirsi e "fissarsi" in posizione, causando una perdita di carburante nel punto di collegamento tra il tubo e il raccordo del motore. La fascetta utilizzata per fissare il tubo al raccordo non è in grado di compensare l'indurimento del tubo di alimentazione del carburante.
NHTSA · Stati Uniti11 apr 199494V066000Anni modello 1989–1993Tradotto automaticamente · originale: ingleseVedi dettagli →
Su alcuni veicoli, il guasto di un componente del sistema di raffreddamento come termostato, pompa dell'acqua o cinghia della ventola può causare un aumento significativo della temperatura del liquido refrigerante e della pressione del sistema. L'aumento della pressione del sistema potrebbe causare la formazione di una crepa o la separazione di una giuntura nell'estremità del nucleo del riscaldamento, che causerebbe l'espulsione di refrigerante caldo dal nucleo del riscaldamento. Questo fluido caldo potrebbe entrare in contatto con gli occupanti dell'auto, causando possibili lesioni personali e/o appannamento delle superfici interne dei finestrini. Correzione: Il tappo del radiatore sarà sostituito con un nuovo tappo di design per evitare l'accumulo di eccessiva pressione nel sistema di raffreddamento.
Transport Canada14 ott 19981998197Anni modello 1988–1993Tradotto automaticamente · originale: ingleseVedi dettagli →
Vehicle description: Passenger vehicles. A malfunction or failure of a coolant system component, such as a thermostat, water pump, or fan belt, can result in significantly increased coolant temperature and system pressure. If the indications of a critical overheating condition is not noticed by the driver, it is possible that damage to, or failure of, a coolant system component could occur.
NHTSA · Stati Uniti4 ago 199898V178000Anni modello 1988–1993Mostrato in inglese originale · traduzione in attesaVedi dettagli →
On certain 318IC, 318IS, 318TI, 325I, 325IC, 325IS, 525I, 525IT, 530I, 530IT, 540I, 740I, 740IL, 840CI and M3, the cruise control and throttle cable are attached to the same throttle valve actuating lever at the throttle housing. It is possible that the plastic bushing on either cable could break causing the outer cable housing to separate from the bushing. Throttle pedal application without cruise control engagement could cause the outer tube to catch on the edge of the broken bushing resulting in the throttle valve remaining partially open. If this were to occur, the car might not decelerate as expected and a crash could occut. Correction: A spring clip will be installed on the outer tube of each cable to prevent dislodgment from the bushing.
Transport Canada9 ott 19971997173Anni modello 1993Mostrato in inglese originale · traduzione in attesaVedi dettagli →
The cruise control and throttle cables are attached to the same throttle valve actuating lever at the throttle housing. It is possible that the plastic bushing on either cable could break due to environmental influences coupled with vibration. If the bushing breaks, the outer cable housing can separate from the bushing. In this case, during application of the throttle pedal without cruise control being engaged, the outer tube could catch on the edge of the broken bushing.
NHTSA · Stati Uniti19 ago 199797V131000Anni modello 1993Mostrato in inglese originale · traduzione in attesaVedi dettagli →
On certain 325I, 325IC, 325IS, 525I, 525IT, 530I, 530IT, 535I, 540I, 735I, 735IL, 740I, 740IL and 750I, the brake light switch may fail due to a reduction of contact force on the "snap contact" system which the switch incorporates. This could cause heat induced distortion of the plastic internal switch parts in the area of the electrical contacts. This could cause the switch to remain either in the ON or the OFF position resulting in the brake lights being continuously illuminated or inoperative regardless of brake pedal operation. Correction: Switch will be replaced with on that utilizes a different contact system.
Transport Canada7 ott 19961996158Anni modello 1990–1993Mostrato in inglese originale · traduzione in attesaVedi dettagli →
On certain 740IA and 740ILA vehicles, the inner throttle cable could break due to a smaller than specification bend in the cable tube. If this were to occur, throttle control would be lost and the engine would return to or remain at idle. Correction: Throttle cable will be replaced with one meeting BMW specifications.
Transport Canada25 apr 19941994081Anni modello 1993Mostrato in inglese originale · traduzione in attesaVedi dettagli →
On certain 535I, 535IA, 735IA, 735ILA vehicles, the nut which secures the throttle valve shaft may not have been tightened with sufficient torque. If the nut were to loosen, it is possible that movement of the throttle valve might be impaired. If this should occur, the vehicle might not decelerate as expected after the gas pedal is released and loos of vehicle control could result. Correction: Vehicles will be inspected and affected throttle housings with undertorqued throttle valve retaining nuts will be replaced.
Transport Canada13 ott 19921992129Anni modello 1991Mostrato in inglese originale · traduzione in attesaVedi dettagli →
On certain 525I, 535I, 735I, 735IL and 750IL vehicles, the front seat center fold-down armrest may contact and damage the seatbelt buckle if the seat back is moved forward to an upright position while the armrest is locked in the down position (horizontal). If this occurs, the release button may be held in the down position, preventing the seatbelt from being latched during the buckle-up operation. Non-latching of the seatbelts will increase the risk of personal injury in the event of a crash. Correction: Front seat safety belt buckles will be replaced with shorter ones that are not susceptible to damage by contact with the armrest.
Transport Canada27 feb 19901990037Anni modello 1988–1990Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Under certain conditions, front seat center, fold-down arm rest may contact the safety belt buckle, causing damage to the release button and preventing the belt tongue from latching when buckling up.
NHTSA · Stati Uniti30 gen 199090V016000Anni modello 1988–1990Mostrato in inglese originale · traduzione in attesaVedi dettagli →
On certain 750IL vehicles, during the assembly process, the gas pedal may not have been properly attached to the floor pan. If the gas pedal is operated in a rough or erratice manner, it may become stuck between the gas pedal stop (on the floor pan) and the carpeting on the transmission tunnel. If this occurs, the pedal might not return fully to the idle position when the driver's foot is removed and loss of control could result. Application of the brake pedal will close the throttle on this model of vehicle. Correction: Accelerator pedal will be inspected and tightened to the floor is required. Also, a modified pedal stop will be installed.
Transport Canada6 apr 19891989046Anni modello 1988–1989Mostrato in inglese originale · traduzione in attesaVedi dettagli →
On certain 325E, 325ES, 528E, 535I, 635CSI and 735I vehicles, the center high mounted brake light could add sufficient electrical load to cause the brake light switch to overheat, eventually leading to melting of the plastic internal switch parts. This could cause the switch plunger to jam in the ON or OFF position. This would render the brake light permanently ON or OFF regardless of brake pedal operation. Correction: A brake light switch with an increased current load capacity will be installed on affected vehicles.
Transport Canada27 nov 19861986134Anni modello 1986–1987Mostrato in inglese originale · traduzione in attesaVedi dettagli →
On certain 725I, 735IA and 750IL vehicles, on the front seats, the seatbacks may not have been fully seated on the recliner arms. This could result in looseness of, or noise in the seat. In extreme cases, during a severe rear impact, the seatback may not support the occupant and increase the risk of injury. Correction: Seatbacks will be inspected and properly seated if required.
Transport Canada25 ago 19881988124Anni modello 1988Mostrato in inglese originale · traduzione in attesaVedi dettagli →
The driver and/or passenger seatbacks may not have been fully attached to the seat base reclining arms (attaching brackets).
NHTSA · Stati Uniti11 ago 198888V135000Anni modello 1988Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).