Bollettino
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
I bollettini tecnici (TSB) sono istruzioni di riparazione che i costruttori inviano ai concessionari su problemi noti. Non sono richiami di sicurezza, ma spesso confermano un difetto.
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
Questo bollettino di servizio descrive una procedura per verificare la presenza di grasso o sigillante in eccesso sull'esterno dello sterzo, in caso di grasso o sigillante visibile in determinate posizioni sul componente.
Questo bollettino tecnico descrive una procedura per verificare la presenza di grasso o sigillante in eccesso sull'esterno dello sterzo, in caso di grasso o sigillante visibile su determinate zone del meccanismo.
Questo bollettino tecnico descrive una procedura per verificare la presenza di grasso o sigillante in eccesso sulla parte esterna dello sterzo, in caso di grasso o sigillante visibile in determinate posizioni sul meccanismo.
This informational bulletin provides a revision for 09-06-04-015B (Vehicles Sitting Outside on Dealer Lots for Extended Periods with Hard Start/No Start Condition) to add the 2015-2018 model years.
This informational bulletin provides information on installing the correct tires for vehicles with the condition of under hard acceleration at higher speeds, the traction control light will flash. Or, they may come in for ABS or general handling/braking concerns.
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
This Preliminary Information communication provides information to the technician about vehicles that after installing a reman High Value V6 engine it has rough running, idle surge, misfire on one or both banks of the engine concern. Technician may find Diagnostic Trouble Codes P0300, P0011 and / or P0016. Technician will need to check the actual engine oil pressure. If oil pressure is within the specifications above, perform all testing listed in PIP4345A including a visual inspection of the camshaft position actuator filter and repair or replace as necessary. Technician will need to contact General Motors Technical Assistance Center for further assistance if the concern is still present.
This Preliminary Information communication provides information to the technician that after installing a re-manufactured High Feature V6 engine the vehicle may rough running, idle surge, Check Engine Lamp or Camshaft Position sensor actuator codes. Technician will need to record the actual engine oil pressure at idle and engine compression readings. Technician will need to perform all testing listed in PIP4345A, if oil pressure and compression readings are within specifications. Technician will need to contact General Motors Technical Assistance Center for further assistance if the concern is not isolated.
This preliminary information communication advises the technician on the steps to diagnose the concern, and the steps to repair the concern of the vehicle cranks but does not start. The technician is to inspect for a sheared cam pin in the engine.
"this technical bulletin provides a procedure to inspect the steering gear for a normal condition of grease or sealant on exterior case of gear due to the manufacturing process."
Oil leak at crankshaft/balancer seal. *tt
Rear main oil seal leak. *tt
No movement and/or transmission oil leak from right inner tripot - right driveshaft not seated. *tt
A stall and/or no crank, no start condition after the wipers are used. The service engine soon light may or may not be illuminated and the customer may report other problems with the cruise control system. A tech 2 diagnostic probe will find numerous dtcs which could include p0608 cruise control, c0460, c0461 steering wheel sensor codes, and possibly a no communication issue with the pcm. Engineering has determined the wiper motor crank arm is contacting the ubec wiring harness and cutting the wires. *tt
Revised camshaft position actuator fastener installation procedure. *tt
Stall, no crank, no start after using the wipers. *tt
Supplement to sit-n-lift seat installation instructions. *tt
Rear disc brake drag or continuing to hold. *tt
Crank, no start condition with no spark. *tt
This service bulletin describes the U.S. Dealer Special Tool Loan Program process.
Questo bollettino informativo preliminare (PI) fornisce al personale delle concessionarie informazioni utili per affrontare con i clienti il tema della corrosione dei componenti del sottoscocca.
Programmazione e attivazione dei moduli OnStar sostitutivi.
Questo bollettino di servizio descrive il processo del Programma di prestito di strumenti speciali per concessionari negli Stati Uniti.
Questo bollettino di servizio fornisce al personale delle concessionarie informazioni su problemi di cambio di marcia della trasmissione automatica e di guidabilità del motore e/o accensione della spia MIL (Malfunction Indicator Lamp) dovuti all'uso di filtri dell'aria a bagno d'olio di tipo aftermarket.
Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).