Su alcuni veicoli passeggeri equipaggiati con motori da 2,4 litri, il tubo flessibile dello sterzo servoassistito ad alta pressione può invecchiare prematuramente per effetto del calore e sviluppare una perdita.
NHTSA · Stati Uniti5 gen 200606V001000Anni modello 1999–2000Tradotto automaticamente · originale: ingleseVedi dettagli →
Vehicle description: Passenger vehicles. Some of these vehicles may have been built with an inadequate weld between the right front brake hose block and the stand-off bracket.
NHTSA · Stati Uniti17 lug 200000V196000Anni modello 2000Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Vehicle description: Passenger vehicles. The rear seat belt anchor does not achieve the loading required by fmvss no. 210, "seat belt assembly anchorages."
NHTSA · Stati Uniti20 mar 199898V063000Anni modello 1995Mostrato in inglese originale · traduzione in attesaVedi dettagli →
An engine cylinder head oil galley plug may not be adequately retained. Inadequate retention of the plug may result in oil leakage which could potentially cause a fire in the engine compartment. Correction: An expansion plug and retaining bracket will be installed over the suspect cylinder head oil galley plug.
Transport Canada10 gen 19961996009Anni modello 1995–1996Mostrato in inglese originale · traduzione in attesaVedi dettagli →
On certain passenger vehicles, the ignition-park interlock of the floor shifter may fail and allow the shifter to be moved out of the park position with the key removed. An inoperative interlock may also allow the key to be removed when the shifter has not been placed in the park position.
NHTSA · Stati Uniti13 gen 200404V021000Anni modello 1995–1999Tradotto automaticamente · originale: ingleseVedi dettagli →
On certain vehicles, incorrect weld wire, in combination with the stainless steel shell of the catalytic converter, will cause rusting at the weld joints and premature failure to the converter assembly. Correction: Dealers will replace the catalytic converter.
Transport Canada18 gen 19991999009Anni modello 1998Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Note: Vehicles equipped with a floor mounted automatic transmission shift lever. A combination of applying a mis-adjusted shifter release button with a low force attempt to shift out of park with the key in the locked position may break the connecting pin in the shifter. If this happens, the "ignition-park" interlock system will not function. Correction: The console shift interlock mechanism will be inspected for proper function. Any vehicles that are not functional after the inspection will have the shift mechanism and cable replaced with a current production "self adjusting" design.
Transport Canada26 ago 19981998165Anni modello 1995–1998Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Vehicle description: Passenger vehicles equipped with automatic transmissions. The adjustment of the cable connecting the console shifter mechanism to the ignition key can cause a trapped key condition which can result in a low force required to depress the shift button. A combination of applying a mis-adjusted release button with a low force attempt to shift out of park with the key in the locked position, can break the connecting pin in the shifter.
NHTSA · Stati Uniti6 ago 199898V183000Anni modello 1995–1998Mostrato in inglese originale · traduzione in attesaVedi dettagli →
These vehicles may not comply with c.M.V.S.S. 210 - seat belt assembly anchorages. The rear seat belt anchor may not achieve the loading required by the standard during testing. Correction: The rear outboard seat belt anchor floor attachments will be inspected for orientation and repositioned if required.
Transport Canada27 mar 19981998061Anni modello 1995Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Certain vehicles do not comply with CMVSS 1103 - exhaust emissions. The calibration of the Powertrain Control Module (PCM) may fail to adequately control CO emissions. Correction: PCM will be reflashed with a new calibration.
Transport Canada21 gen 19981998010Anni modello 1996Mostrato in inglese originale · traduzione in attesaVedi dettagli →
On certain vehicles, the lower control arm ball joint may separate due to loss of lubrication. This separation could result in loss of vehicle control and a crash without prior warning. Correction: Ball joint end housing cover seal will be inspected for leakage and the rubber boot will be inspected for damage. If the cover seal leaks or the boot is damaged, the lower control arm will be replaced.
Transport Canada20 nov 19971997205Anni modello 1995–1997Mostrato in inglese originale · traduzione in attesaVedi dettagli →
The primary/secondary hood latch spring may not remain in position during hood closing, which can result in loss of both the primary and secondary latch function. Loss of hood function can result in a hood fly-up condition. Correction: The secondary hood latch spring will be replaced with one having a longer end hook.
Transport Canada19 giu 19971997123Anni modello 1996–1997Mostrato in inglese originale · traduzione in attesaVedi dettagli →
On certain vehicles, the brake master cylinder may leak brake fluid due to a damaged double lip rear piston seal. Brake fluid leakage may result in diminished effectiveness of one portion of the split brake system. Correction: Rear brake master cylinder piston assemblies will be replaced.
Transport Canada17 mag 19961996079Anni modello 1995–1996Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Corrosion of the abs hydraulic control unit may cause the solenoid valves to stick in the open position. If either front wheel valve sticks, the vehicle may tend to deviate from a straight stop when the brakes are applied. Correction: A plate will be installed on the abs hydraulic control unit and silicone grease injected into the solenoid cavity to eliminate the potential for this condition.
Transport Canada17 mag 19961996078Anni modello 1995–1996Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Veicolo: Alcuni autoveicoli passeggeri, pick-up e sport utility vehicle non sono conformi ai requisiti della FMVSS n. 225, "Sistemi di ancoraggio per seggiolini per bambini". Alcuni dei manuali del proprietario di questi veicoli non contengono le istruzioni che descrivono, passo dopo passo e con diagrammi, la procedura corretta per fissare la cinghia di ritenuta (tether) del seggiolino per bambini all'ancoraggio superiore.
NHTSA · Stati Uniti9 nov 200000V366000Anni modello 2000Tradotto automaticamente · originale: ingleseVedi dettagli →
Vehicle description: Passenger vehicles. The affected vehicles were built with incorrect child lock instruction labels.
NHTSA · Stati Uniti2 mar 200000V066000Anni modello 2000Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).