Sterzo: Volante/manubrio
L'operazione di corazzatura in zinco eseguita sull'albero superiore della colonna dello sterzo causò l'abbracciamento e la rottura dell'otturatore.
🔔 Crea un account gratuito per ricevere avvisi via e-mail su Chrysler LeBaron (tutte le generazioni)
L'operazione di corazzatura in zinco eseguita sull'albero superiore della colonna dello sterzo causò l'abbracciamento e la rottura dell'otturatore.
Un bullone di accoppiamento della colonna dello sterzo può fratturarsi a causa della fragilità da idrogeno, causando la perdita del carico di serraggio sull'aggancio dell'albero della colonna dello sterzo con conseguente perdita del controllo dello sterzo. Correzione: I bulloni di accoppiamento della colonna dello sterzo placcati in zinco saranno sostituiti da un bullone rivestito a fosfato.
Air bag inflator modules may not contain diffuser holes between the ignitor and propellant chambers.
La guarnizione del coperchio delle valvole del motore può disallinearsi e consentire una perdita di olio motore in corrispondenza della guarnizione.
Su veicoli con motore EFI da 2,2 litri o 2,5 litri (non turbo), la guarnizione del coperchio punterie potrebbe perdere olio, creando il rischio di un incendio nel vano motore. Correzione: la guarnizione del coperchio punterie verrà sostituita con un coperchio modificato e sigillante RTV applicato al posto della guarnizione.
Può verificarsi una perdita di carburante durante il funzionamento a bassa temperatura ambiente nei punti di collegamento del tubo di alimentazione del carburante nel vano motore con il regolatore di pressione e con il condotto di distribuzione del carburante (fuel rail).
A resister in the instrument cluster may be subjected to an electrical current overload due to failure of a switching transister.The overheated resister could possibly start a fire in the instrument panel.
A resistor in the electronic panel cluster may be subjected to an electrical current overload due to failure of a switching transistor. Consequence of defect: The overheated resistor could ignite and start an instrument panel fire.
Su alcuni veicoli equipaggiati con motore turbo da 2,2 litri, un morsetto del tubo carburante al regolatore di pressione del sistema di alimentazione non serrato adeguatamente potrebbe causare una perdita di carburante e determinare il rischio di incendio nel vano motore.
Un tubo flessibile del carburante nel vano motore, instradato verso il regolatore di pressione del sistema di alimentazione, potrebbe presentare una fascetta stringitubo non sufficientemente serrata. Conseguenza del difetto: il tubo flessibile del carburante potrebbe perdere e provocare un incendio nel vano motore.
The potential for fuel leakage exists in the engine compartment at the fuel reservoir seam and its hose connections. The fuel reservoir is a silver colored can mounted to the air cleaner.
On certain vehicles, the hydraulic brake tube may interfere with the exhaust system hanger bolt and eventually result in brake fluid leakage. This could create a partial loss of braking capability. Should this occur, the brake warning light on the instrument panel will warn the driver.
Hydraulic brake tube routing to the rear wheels may alloow interference between the tube and the rear park brake cable. Resulting abrasion could cause tube failure and partial loss of braking capability. The instrument panel light will provide warning of the partial loss.
These vehicles may not comply with c.M.V.S.S 207 - anchorage of seats. The travelling seat buckle lock bars (seat belt anchors) on some vehicles equipped with bucket seats may have inadequate strength and may not meet the static load requirements of the standard. Correction: Lock bar assemblies will be replaced.
An improperly adjusted hood latch assembly could prevent engagement of the secondary latching mechanism. In such a case the secondary latch would not function to restrain the hood in the event that the primary latch was not engaged for any reason and hood fly-up could occur, blocking the driver's vision. Correction: Secondary hood latch will be inspected and adjusted if necessary, to ensure proper engagement.
The hood latch assembly may not have been properly installed and the secondary hood latch may be prevented from engaging when the hood is closed.
In areas of high road salt use, vehicles may experience a bonded disc brake pad separation from the front or rear brake plates. This could cause a reduction in brake performance and a possible vehicle crash. Correction: Bonded disc brake linings will be replaced on affected vehicles.
The bonded disc brake linings may separate from the shoes due to a bonding deficiency which may allow corrosion degradation of the bond attachment.
Parking brake cables may be mismatched in length resulting in reduced parking brake application on one wheel and so may not comply with c.M.V.S.S. 105-hydraulic brake systems. Correction: Vehicles will be inspected and those with mismatched cables will have the longer cable replaced with a shorter version.
On vehicles with a 50/50 bench seat, the front outboard passenger seat belt may become difficult to latch and/ or unlatch due to a belt webbing stiffener which could enter the buckle housing and dislodge the buckle latch guide. This could also result in partial latch engagement. Correction: Buckle assembly will be replaced with a revised version if necessary.
Front outboard safety belt may become difficult to latch and or unlatch due to a webbing stiffener entering the buckle housing and dislodging the buckle latch guide.
Mismatched parking brake cable lengths to the rear wheels reduces braking ability of one of the rear wheels, in violation of fmvss 105.
Nota: Veicoli situati in Ontario, Quebec, New Brunswick, Nova Scotia, Prince Edward Island e Newfoundland. Questi veicoli potrebbero non essere conformi alla norma C.M.V.S.S. 108 - illuminazione a causa di un guasto per corrosione del modulo delle luci diurne (DRL). Correzione: il modulo DRL sarà sostituito con uno dotato di materiale di riempimento (potting) aggiuntivo che copre tutti i componenti precedentemente esposti.
I sensori d'urto frontale del sistema airbag (due) potrebbero non essere fissati correttamente ai relativi supporti di montaggio.
I bulloni delle guide della pinza del freno a disco anteriore potrebbero non essere stati serrati adeguatamente. Ciò potrebbe creare la possibilità di un certo grado di funzionamento anomalo dei freni. Correzione: i bulloni delle guide della pinza del freno anteriore dovranno essere serrati alla coppia di serraggio specificata.
Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).