Lettura libera · account gratuito per contribuireErede di Anticars (2000)

Mazda MX-5 (ND)

2015– · 7 difetti documentati · 4 mercati

I bollettini tecnici (TSB) sono istruzioni di riparazione che i costruttori inviano ai concessionari su problemi noti. Non sono richiami di sicurezza, ma spesso confermano un difetto.

Anno modello
BollettinoCriticoMotoreNA

Bollettino

On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is caused by high amounts of sulfur in the gasoline being used in the vehicle. Sulfur is normally eliminated during the refining process, but the EPA regulation of sulfur in gasoline differs from state to state. Vehicles using fuel containing high amounts of sulfur will most likely emit sulfur smell from the exhaust system.When high sulfur fuel is burned, there is a chemical reaction in the catalytic converter causing the sulfur tooxidize. As the vehicle is driven, the oxidizing reaction odor in the converter will decrease with mileage and age.

NHTSA · bollettino del costruttore10153311Anni modello 2019Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoCarrozzeriaNA

Bollettino

Questo bollettino sostituisce il/i bollettino/i precedentemente emessi elencati di seguito. I cambiamenti sono indicati in rosso. 09-012/21 12/13/21, 06/10/21 e 04/27/21 DESCRIZIONE Alcuni clienti possono manifestare tutti i seguenti sintomi: Il funzionamento di chiusura/sblocco della porta non funziona utilizzando il pulsante del trasmettitore remoto. 1. L'operazione di chiusura/sblocco della porta non funziona utilizzando il sensore touch di chiusura/rilascio della porta. 2. Il motore non si avvia con l'interruttore di accensione. 3. Il trasmettitore funziona da solo. 4. La batteria della chiave si scarica più velocemente del solito. 5. Sintomi 1-3: Questo può essere causato da un carico eccessivo applicato al trasmettitore remoto, deformando i terminali elettrici e creando un cattivo contatto con la batteria. Per eliminare questo problema, la struttura del trasmettitore remoto è stata modificata per ridurre la deformazione dei terminali elettrici. Sintomo 4-5: Questo può essere causato quando viene applicato un carico eccessivo al trasmettitore remoto, creando uno spazio intorno alla guarnizione dove l'umidità entra e corrode la scheda elettronica, scaricando la batteria della chiave più rapidamente del solito. Per eliminare questo problema, lo spessore della parete del case sulla superficie di montaggio della guarnizione è stato aumentato e la resistenza di adesione dei componenti è stata migliorata per prevenire deformazioni. PROCEDURA DI RIPARAZIONE Se la batteria è difettosa o installata in modo errato, sostituisci la batteria e/o installala correttamente. Se la funzione di risparmio energetico a distanza è disattivata e la batteria è buona e installata correttamente, sostituisci il trasmettitore remoto, difettoso, con uno modificato secondo le istruzioni su MGSS (PROGRAMMAZIONE DEI PEZZI LEGATI AL SISTEMA IMMOBILIZZATORE). NOTA: NON sostituire altri trasmettitori remoti del veicolo se non stanno riscontrando problemi.

NHTSA · bollettino del costruttore11034436Anni modello 2020Tradotto automaticamente · originale: ingleseVedi dettagli →
BollettinoModeratoMotoreNA

Bollettino

Some vehicles may exhibit oil leakage from the drive belt auto tensioner and rattling noises from the engine compartment. This may be caused by insufficient sealing at the drive belt auto tensioner damper when the auto tensioner fully operates under both high ambient temperature and high load conditions. To eliminate this concern, the shape of the drive belt auto tensioner damper has been changed.

NHTSA · bollettino del costruttore10238663Anni modello 2019Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoSospensioniNA

Bollettino

Il sistema di monitoraggio dell'angolo cieco (BSM) può presentare un malfunzionamento con i seguenti sintomi se i sensori radar laterali posteriori sono installati con orientamento errato. - Il sistema BSM indica la presenza di un veicolo sul lato opposto. - L'anello indicatore i-ACTIVSENSE non diventa verde. - L'avviso di traffico posteriore in retromarcia (RCTA) non funziona. - Sensore radar laterale posteriore

NHTSA · bollettino del costruttore10222563Anni modello 2023Tradotto automaticamente · originale: ingleseVedi dettagli →
BollettinoModeratoFreniNA

Bollettino

Some vehicles may experience a lack of power and the check engine light on with DTC P061B:00 stored in PCM memory under one of the following conditions (A or B). - DTC P061B:00 - [PCM] Internal control module torque calculation performance problem. Condition Condition Description A When cranking is interrupted (likely occurs when the brake pedal is released during cranking) B When accelerating from 1300-1600 rpm with wide open throttle Due to an improper control logic of the PCM, the engine torque calculation error detection is too sensitive. To eliminate this concern, the PCM software has been modified.

NHTSA · bollettino del costruttore10218722Anni modello 2019Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoFreniNA

Bollettino

Clunk/Rattle noise from rear brake

NHTSA · bollettino del costruttore10213396Anni modello 2016Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoCarrozzeriaNA

Bollettino

Some vehicles may experience one of the following 2 symptoms, even though the windshield is clear. Under certain driving conditions, the Forward Sensing Camera (FSC) may detect a dirty windshield (not clear). NOTE FOR CUSTOMER: The FSC may not work properly under the conditions: The windshield is not clear. The FSC lens is not clear. Driving in heavy rain, dense fog or snow, or into the sun. Driving on a road with no or blurred road lane markings. When the windshield becomes foggy in the winter time or other cold weather conditions and LDWS/HBC warning lights turn on, drive with the defroster on for about 10 minutes. This will help clear the foggy windshield at the FSC.

NHTSA · bollettino del costruttore10185957Anni modello 2016Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoAltroNA

Bollettino

Some vehicles may exhibit the inner cloth (A) falling down at the rear end causing a poor appearance and obstructing the view of the back window. This is caused by the J-hook binding holding the inner cloth coming loose during the opening/closing of the convertible top, from vibration during driving or from high ambient temperatures. To correct the problem, two top-protector clips have been additionally installed to both side edges of the J-hook to prevent the J-hook from loosening and separating.

NHTSA · bollettino del costruttore10185955Anni modello 2016Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoElettronicaNA

Bollettino

Ldws and hbc warning lights on and dtc c1001:92

NHTSA · bollettino del costruttore10186337Anni modello 2016Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoElettronicaNA

Bollettino

If you experience issues with the current version of ID's such as missing tools or modules not showing after completing a network test, be advised that we are aware of these issues and are working to resolve them. As a counter measure, it is advised that you un-install ids and re-install version 103.00 and "do not update" until further notice.

NHTSA · bollettino del costruttore10185813Anni modello 2017Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoMotoreNA

Bollettino

If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage.

NHTSA · bollettino del costruttore10165676Anni modello 2019Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoCarrozzeriaNA

Bollettino

Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.

NHTSA · bollettino del costruttore10165350Anni modello 2019Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoAltroNA

Bollettino

Due to a database error discovered with IDS 114.00-114.02 release (which affects Recall 3719F), it will be necessary to uninstall IDS 114 and install IDS 113.00 and 113.06 update. The Recall can be performed after removing IDS 114 and installing IDS 113. This SA will be updated when more information is available.

NHTSA · bollettino del costruttore10163333Anni modello 2019Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoAltroNA

Bollettino

On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing the accessory locking lug nuts, make sure to use the appropriate part number for the vehicle you are working on.

NHTSA · bollettino del costruttore10159199Anni modello 2018–2019Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoSospensioniNA

Bollettino

On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing new lug nuts or the accessory Wheel Lock Set, make sure to use the appropriate part number for the vehicle you are working on.

NHTSA · bollettino del costruttore10159196Anni modello 2018–2019Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoAltroNA

Bollettino

In supporto della nuova distribuzione MRT, Mazda invierà ai concessionari un nuovo Rilevatore di perdite diagnostico a doppio uso a partire da marzo 2019. I video di formazione saranno pubblicati su MGSS a breve, e le procedure del Manuale d'officina saranno revisionate gradualmente.

NHTSA · bollettino del costruttore10154879Anni modello 2019Tradotto automaticamente · originale: ingleseVedi dettagli →
BollettinoModeratoSospensioniNA

Bollettino

Subject: Mazda Service Program (MSP) 53. 2019 CX-3 & 2018-2019 MX-5 With Direct Tire Pressure Monitoring System (TPMS) Panic Alarm System Activates While Driving. Mazda Motor Corporation has decided to conduct a Mazda Service Program (MSP) on certain 2019 CX-3 vehicles produced from February 27, 2018 through October 12, 2018 and 2018-2019 MX-5 vehicles produced from October 3, 2017 through October 15, 2018. On certain subject vehicles equipped with Direct TPMS (TPMS wheel sensor is directly mounted on each wheel), it is possible that the panic alarm system may activate while driving, and the horn may sound intermittently, and hazard warning lights may flash. The panic alarm concern will stop after cycling the ignition switch off, then on again. No DTCs are stored. Action Required: Beginning today, reprogram the body control module (BCM) to the latest calibration using MMDS for all affected CX-3 and MX-5 vehicles in dealer inventory, and when customers bring their vehicles for maintenance, or other service/warranty work. The subject vehicles must not be delivered to customers until the repair of MSP53 is completed. Please inform the customer that the BCM will be reprogrammed to the latest calibration, free of charge. If a vehicle is sold with an open MSP53 your Step 3 PDI warranty claim will be subject to debit.

NHTSA · bollettino del costruttore10154528Anni modello 2018–2019Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoSospensioniNA

Bollettino

On certain subject vehicles, it is possible that the panic alarm system may activate while driving, and the horn may sound intermittently and hazard warning lights may flash. The panic alarm concern will stop after cycling the ignition switch off, then on again. No DTCs are stored. Some TPMS wheel sensor IDs on the concerned vehicle or other vehicles nearby may cause the error in the body control module (BCM). Air pressure data transmitted from the wheel sensors may be recognized by the BCM as if the panic button on the remote transmitter has been pressed.

NHTSA · bollettino del costruttore10154531Anni modello 2018–2019Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoSospensioniNA

Bollettino

Se un veicolo presenta vibrazioni della carrozzeria o shimmy del volante durante la guida e la causa principale viene individuata nel bilanciamento degli pneumatici, bilanciare nuovamente gli pneumatici utilizzando una bilanciatrice Hunter GSP9700 o equivalente. Se la concessionaria non dispone di una bilanciatrice GSP9700 o equivalente, affidare il veicolo a un'officina esterna per la riparazione. Per trovare la sede di una GSP9700 vicino alla propria concessionaria, visitare il sito web di Hunter all'indirizzo www.gsp9700.com e fare clic su "Locate a GSP9700 Road Force Balancer" ("Trova una bilanciatrice Road Force GSP9700").

NHTSA · bollettino del costruttore10154139Anni modello 2019Tradotto automaticamente · originale: ingleseVedi dettagli →
BollettinoModeratoFreniNA

Bollettino

Alcuni veicoli presentano problemi legati ai freni, come rumorosità dei freni, vibrazioni (judder) o trascinamento dei freni. Se ricevete un reclamo da parte del cliente per uno di questi sintomi, consultate le seguenti informazioni per capire perché i sintomi possono presentarsi e per assistere meglio il cliente nella risoluzione del suo specifico problema ai freni.

NHTSA · bollettino del costruttore10153227Anni modello 2019Tradotto automaticamente · originale: ingleseVedi dettagli →
BollettinoModeratoAbitacoloNA

Bollettino

Queste informazioni sono fornite per aiutare a risolvere i problemi legati all'accensione della spia di disattivazione dell'airbag del passeggero (PAD) durante l'assistenza al veicolo.

NHTSA · bollettino del costruttore10153329Anni modello 2019Tradotto automaticamente · originale: ingleseVedi dettagli →
BollettinoModeratoAltroNA

Bollettino

Questo bollettino di servizio fornisce informazioni sul corretto utilizzo del tappetino del conducente per evitare potenziali interferenze con i pedali. Le seguenti sono possibili cause di interferenza del tappetino, che possono essere evitate con un utilizzo corretto. Il tappetino si sposta in avanti a causa di un'installazione non corretta. Viene utilizzato un tappetino non appropriato (ad esempio un tappetino aftermarket, non previsto di serie o non originale). Il tappetino è sovrapposto a un altro tappetino.

NHTSA · bollettino del costruttore10153331Anni modello 2019Tradotto automaticamente · originale: ingleseVedi dettagli →
BollettinoModeratoSospensioniNA

Bollettino

Dal 1° maggio 2018, i veicoli prodotti in Giappone utilizzano dadi delle ruote esagonali da 17 mm invece che da 21 mm, con lo stesso passo di filettatura. Quando si installano nuovi dadi delle ruote o il kit accessorio Wheel Lock Set, assicurarsi di utilizzare il numero di parte corretto per il veicolo su cui si sta lavorando. NOTA: la Mazda3 prodotta in Messico non è interessata. Utilizzare il GEPC o il sito web degli accessori Mazda [MXConnect (dealers.mazdausa.com)] per consultare il numero di parte corretto per il veicolo su cui si sta lavorando.

NHTSA · bollettino del costruttore10153226Anni modello 2018–2019Tradotto automaticamente · originale: ingleseVedi dettagli →
BollettinoModeratoElettronicaNA

Bollettino

Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored inmemory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem P2507:00: PCM battery voltage low input As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed. NOTE: The odometer will display "F0-002" during transport mode (room fuse 15A removed). Transport mode is canceled when room fuse 15A is installed or the vehicle odometer is more than 12.4mi (20km). Vehicles in dealer inventory with this concern should be repaired using the following repair procedure.

NHTSA · bollettino del costruttore10153310Anni modello 2019Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoSospensioniNA

Bollettino

I veicoli elencati sopra sono dotati di un sistema di avviamento/arresto del motore con pulsante. Diversamente dai precedenti modelli Mazda, sul piantone dello sterzo non è presente alcun cilindro per la chiave. Pertanto, il motore non può essere avviato con la chiave di emergenza se il fusibile dell'abitacolo è stato rimosso o se la batteria del trasmettitore è scarica.

NHTSA · bollettino del costruttore10153313Anni modello 2019Tradotto automaticamente · originale: ingleseVedi dettagli →
Meno recenti →

Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).