Lettura libera · account gratuito per contribuireErede di Anticars (2000)

Mini Hatch II

2006–2013 · 18 difetti documentati · 2 mercati

I bollettini tecnici (TSB) sono istruzioni di riparazione che i costruttori inviano ai concessionari su problemi noti. Non sono richiami di sicurezza, ma spesso confermano un difetto.

Anno modello
BollettinoModeratoElettronicaNA

Bollettino

N12 Tank leak diagnostic module (DMTL) pump:limited warranty extension to 10 years/120,000 miles

NHTSA · bollettino del costruttore10216756Anni modello 2009Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoElettronicaNA

Bollettino

CLASS ACTION SETTLEMENT: N14 HIGH-PRESSURE FUEL PUMP (HDP) SERVICE BENEFIT CLASS VEHICLES: The MINI vehicle may experience a sudden engine operational failure reduced or loss of power while driving and the malfunction indicator lamp (MIL) may be illuminated along with high-pressure fuel pumprelated faults stored in the Engine Control Module (DME). PROCEDURE Perform the corresponding diagnosis/vehicle test and run the test plans to completion as applicable.

NHTSA · bollettino del costruttore10171506Anni modello 2009Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoMotoreNA

Bollettino

Air Conditioning System Leak Testing. The customer complains of poor or no air conditioning cooling. After further diagnosis, the system is found to be low or empty of a refrigerant charge, but when using an electronic leak detector, no leak can be found. CAUSE: In most cases, an electronic leak detector is not sufficient for identifying small leaks in the system. Electronic leak detectors can give false alarms and can lead to an improper diagnosis of small leaks. A leak cannot be located exactly if accessibility is impaired (in the case of the expansion valve, evaporator or condenser).

NHTSA · bollettino del costruttore10162461Anni modello 2009Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoFreniNA

Bollettino

Brake Fluid Maintenance Service: 36-Month Interval. The CBS displays the first brake fluid service as a 36-month interval from the date of production, instead of the appropriate 24-month interval. Only vehicles within the specified production range can be serviced and covered by this bulletin. For vehicles outside of the production range specified in this bulletin, refer to the CBS and/or Key Read information for the brake fluid service.

NHTSA · bollettino del costruttore10152335Anni modello 2011Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoElettronicaNA

Bollettino

"N12 Tank Leak Diagnostic Module (DMTL) Pump: Limited Warranty Extension to 10 Years/120,000 Miles. INFORMATION This updated version of this bulletin now includes the addition of the model year 2009 R55, R56 and R57 MINI Cooper vehicles with the N12 engine. For the above-referenced vehicles, MINI USA, a division of BMW of North America, LLC (""MINI USA"") is extending the limited warranty for the Tank Leak Diagnostic Module (DMTL) Pump to: 10 years/120,000 miles as determined by the vehicle's original in-service date Component #1: This ""component specific"" limited warranty extension applies to defects in materials and workmanship and is subject to the applicable vehicle and coverage eligibility requirements, exclusions and limitations that apply to the MINI New Passenger Car Limited Warranty. GRUSB0116-04 This bulletin is notice of a ""limited warranty extension."" This is NOT a notice of a Recall or Service Action. There is no immediate repair required unless the MINI vehicle is currently experiencing this problem. Even though this is NOT a Recall, MINI USA will be sending VIN-specific customer notification letters in a phased release. Customer Notification Letter - VIN and Component-specific Warranty Extension Even though this is NOT a Recall, MINI USA will be sending VIN-specific customer notification letters in a phased release for the additional MY 2009 vehicles."

NHTSA · bollettino del costruttore10151222Anni modello 2009Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoMotoreNA

Bollettino

During Engine Oil Service a Small O-Ring Is Found in the Oil Filter Housing. No customer complaint has been received. During the scheduled engine oil service, the technician notices a black rubber o-ring lying on the bottom of the engine oil filter housing. The o-ring has been dislodged from the non-return valve inside the engine oil filter housing. No subsequent engine damage occurs from the dislodged o-ring. Engine oil filter housing (1) Rubber o-ring (2) The material dimensions of the rubber o-ring are not satisfactory, allowing it to become dislodged from its installation location.

NHTSA · bollettino del costruttore10150347Anni modello 2009Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoFreniNA

Bollettino

"Erroneous ""Service due"" Message Though Brake Lining Thickness Sufficient. The CBS data calculated for the remaining distance of the front and/or rear brake pads does not agree with the actual brake pad thickness. The yellow brake lining service due indicator illuminates even though the pad thickness is greater than the minimum wear limit (approximately 3.7 mm); the brake wear sensor has not yet been activated (from a thickness of approx. 4.2 mm). In some cases, the red warning message may already be active. The CBS front/rear brake display is based on a mathematical calculation. Various influences are incorporated into this calculation (for example, vehicle speed, brake pressure, and rotor temperature). Due to changing driving characteristics and/or unfavorable environmental conditions, the calculated remaining distance may differ from actual pad thickness."

NHTSA · bollettino del costruttore10150306Anni modello 2011Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoFreniNA

Bollettino

Brake Fluid Maintenance Service: 36-Month Interval. The coding in these vehicles has the CBS displaying the first brake fluid service as a 36-month interval from the date of production, instead of the appropriate 24-month interval.

NHTSA · bollettino del costruttore10150047Anni modello 2011–2012Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoFreniNA

Bollettino

Brake Fluid Maintenance Service: 36-Month Interval. The CBS displays the first brake fluid service as a 36-month interval from the date of production, instead of the appropriate 24-month interval.

NHTSA · bollettino del costruttore10150239Anni modello 2011–2012Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoFreniNA

Bollettino

"?SI M34 01 13 November 2013 BrakesTechnical Service This Service Information bulletin supersedes SI 34 01 13 dated October 2013. designates changes to this revision SUBJECT Erroneous ""Service due"" Message Though Brake Lining Thickness Sufficient. The CBS data calculated for the remaining distance of the front and/or rear brake pads does not agree with the actual brake pad thickness. The yellow brake lining service due indicator illuminates even though the pad thickness is greater than the minimum wear limit (approximately 3.7 mm); the brake wear sensor has not yet been activated (from a thickness of approx. 4.2 mm). In some cases, the red warning message may already be active. The CBS front/rear brake display is based on a mathematical calculation. Various influences are incorporated into this calculation (for example, vehicle speed, brake pressure, and rotor temperature). Due to changing driving characteristics and/or unfavorable environmental conditions, the calculated remaining distance may differ from actual pad thickness."

NHTSA · bollettino del costruttore10150205Anni modello 2011Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoMotoreNA

Bollettino

The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid.

NHTSA · bollettino del costruttore10150087Anni modello 2011Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoMotoreNA

Bollettino

Engine Oil Leak. The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid.

NHTSA · bollettino del costruttore10149500Anni modello 2009Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoMotoreNA

Bollettino

Service Action: Replace the Coolant Pump. Coolant is leaking from the coolant pump. CAUSE The coolant pump may develop cracks in the plastic housing. These cracks may result in a coolant leak.

NHTSA · bollettino del costruttore10149501Anni modello 2011Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoSospensioniNA

Bollettino

Service Action: Retrofit John Cooper Works Steering Wheel Gearshift Paddles. A number of these vehicles were inadvertently produced without the standard gearshift paddles. Vehicle option ordering error

NHTSA · bollettino del costruttore10149503Anni modello 2012Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoAltroNA

Bollettino

"White Wear Marks on Canvas Top. Wear marks appear on the convertible top on the left and/or right side C-pillar areas. A For vehicles produced to December 12, 2011 1. Replace the defective canvas convertible top. Refer to ISTA Repair Instruction 54 34 120, ""Replacing soft top fabric."" Note: The following repair steps must be performed before the new top is installed to prevent a repeat repair for wear marks. 2. With the defective canvas cover removed, the current main pillars must be replaced. Refer to ISTA Repair Instruction 54 34 996, ""Replacing left or right main pillar."" 3. The current locking mechanisms and bump stops must be replaced as well. Refer to ISTA Repair Instruction 54 34 196, ""Removing and installing / replacing both stowage locks."" The repair kit* needed is listed below. 7. Reinstall the removed parts in the reverse order of their removal. 8. Operate the top several times to quality check the repair."

NHTSA · bollettino del costruttore10149505Anni modello 2009Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoFreniNA

Bollettino

Erroneous "Service due" Message Though Brake Lining Thickness Sufficient. The CBS data calculated for the remaining distance of the front and/or rear brake pads does not agree with the actual brake pad thickness. The yellow brake lining service due indicator illuminates even though the pad thickness is greater than the minimum wear limit (approximately 3.7 mm); the brake wear sensor has not yet been activated (from a thickness of approx. 4.2 mm). In some cases, the red warning message may already be active. The CBS front/rear brake display is based on a mathematical calculation. Various influences are incorporated into this calculation (for example, vehicle speed, brake pressure, and rotor temperature). Due to changing driving characteristics and/or unfavorable environmental conditions, the calculated remaining distance may differ from actual pad thickness.

NHTSA · bollettino del costruttore10149332Anni modello 2009Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoMotoreNA

Bollettino

Engine Oil Leak. The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid.

NHTSA · bollettino del costruttore10149323Anni modello 2011Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoFreniNA

Bollettino

ABS/DSC Control During Light Braking. When driving slowly over uneven road surfaces, there may sometimes be pre-mature ABS application relative to the driving situation with the brake lightly applied. Software in the Dynamic Stability Control unit (DSC)

NHTSA · bollettino del costruttore10149331Anni modello 2011Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoMotoreNA

Bollettino

N16 Engine: Oil Leak from Cylinder Head Sealing Plug. An oil leak can develop at a sealing plug located in the cylinder head, just below the vacuum pump. The sealing plug was not tightened sufficiently during production.

NHTSA · bollettino del costruttore10148441Anni modello 2009–2012Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoMotoreNA

Bollettino

N16 Engine: Oil Leak from Cylinder Head Sealing Plug. An oil leak can develop at a sealing plug located in the cylinder head, just below the vacuum pump. CAUSE The sealing plug was not tightened sufficiently during production.

NHTSA · bollettino del costruttore10148391Anni modello 2009–2012Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoElettronicaNA

Bollettino

N16: Fault 274D Mixture Adaptation Is Stored in the DME. Certain low speed, light-load driving conditions at lower outside temperatures could cause the Service Engine Soon lamp (MIL) to illuminate. The following fault would be stored in the DME: Fault 274D: Mixture adaptation, lower engine speed range (mixture too lean) CAUSE 1. Possible intake/exhaust leaks, or a faulty component as listed in the test plan 2. Unfavorable DME software

NHTSA · bollettino del costruttore10148346Anni modello 2009–2012Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoFreniNA

Bollettino

Erroneous "Service due" Message Although Brake Lining Thickness is Above Minimum Specification. The yellow "Service Due" warning message lights up in the instrument cluster, even though the brake pad thickness is more than 4.2mm (above the thickness at which the pad sensor intervenes). The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. Software calculation of the brake pad wear model in the DSC.

NHTSA · bollettino del costruttore10148349Anni modello 2009Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoMotoreNA

Bollettino

N16 and N18 Engine Oil Leak. The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid.

NHTSA · bollettino del costruttore10148293Anni modello 2009Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoElettronicaNA

Bollettino

Service Action: Bluetooth Software (KISU Data) Update. This Service Action is being released to improve customer satisfaction as we strive to be number 1 in the JD Power Initial Quality Survey (IQS). This new KISU software improves the Bluetooth functionality in our vehicles, and it helps to keep us up-to-date with technology innovation. Please implement the Bluetooth Software Update Service Action. This Service Action will be in effect until March 2015. Thank you for your continuous support. Improved KISU data (Customer Initiated Software Update) is now available for installation in these vehicles via the USB port. Improved functionality for COMBOX: z Detailed view of the text messages z Android device connection stability (linked contacts causing BT disconnection) Improved functionality for HU-H: z Reconnection strategy z 3rd Party App Metadata - Album art and song title Note: This Service Action is to be completed only at the dealer. You (dealers) will be receiving vehicles from the VDCs that will require this Service Action to be completed prior to customer delivery.

NHTSA · bollettino del costruttore10148212Anni modello 2009Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoElettronicaNA

Bollettino

"N16 and N18 Engine Oil Leak. The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid. DIAGNOSTIC Below is the procedure for identifying how far the engine oil has migrated inside the engine electrical harness, when this issue occurs, if at all. The procedure must be followed very carefully so that the proper repair is identified. 1. Disconnect the oil pump volume control solenoid valve electrical connection per Repair Instructions 11 41 519 ""Removing and installing or replacing the solenoid valve (engine oil pump)."" Inspect the electrical connector; if no engine oil is found inside the electrical connector, perform the oil pump volume control valve repair procedure. If engine oil is found inside the electrical connector, proceed to diagnostic procedure step 2. 2. Remove the cover from the DME and remove all three electrical connectors from the DME. Inspect the connectors for traces of engine oil. If no engine oil is found, perform the oil pump volume control valve repair procedure and replace the engine section of the wire harness. Refer to EPC for the additional part number. If engine oil is found in the DME connector, proceed to step 3. 3. If engine oil is found in the DME electrical connector, perform the oil pump volume control valve repair procedure, replace the engine section of the wire harness and replace the DME. Refer to EPC for the additional part numbers. Do not remove the engine oil pan. Do not replace the oil pump volume control valve. Do not replace engine oil pump. OIL PUMP VOLUME CONTROL VALVE REPAIR"

NHTSA · bollettino del costruttore10147956Anni modello 2009Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Meno recenti →

Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).