Steering:Gear box (other than rack and pinion)
The steering intermediate shaft could have been improperly assembled causing the shaft lower coupling to loosen and rotate on the steering gear input shaft.
🔔 Crea un account gratuito per ricevere avvisi via e-mail su Pontiac Firebird (tutte le generazioni)
The steering intermediate shaft could have been improperly assembled causing the shaft lower coupling to loosen and rotate on the steering gear input shaft.
These vehicles may have been built with an improperly assembled steering intermediate shaft. This condition could cause the intermediate shaft lower coupling to loosen and rotate on the steering gear input shaft. If this were to occur while the vehicle was in motion, a loss of steering control could result and a crash could occur without prior warning. Correction: Steering shaft will be inspected and lower coupling will be replaced if required.
Il giunto saldato del collo di riempimento del carburante può sviluppare crepe o perdite da fori di spillo, il che non è conforme alla FMVSS n. 301, "fuel system integrity". Le crepe e i fori possono consentire la fuoriuscita di vapori e di carburante.
Questi veicoli potrebbero presentare crepe o "fori di spillo" nel punto di saldatura del collo di riempimento del serbatoio del carburante. Ciò potrebbe causare odore di carburante o perdite di carburante. In presenza di una fonte di accensione, la perdita di carburante dovuta a questa condizione potrebbe provocare un incendio del veicolo. Correzione: i serbatoi del carburante dei veicoli interessati saranno ispezionati per verificare la presenza di perdite e sostituiti se necessario.
Note: Vehicle located in ontario. The fuel line could develop a hole due to contact with the hot air (air injection reaction) check valve. This could result in fuel leakage and an engine compartment fire. Correction: Fuel line bundle will be inspected for heat damage and replaced if necessary. Fuel line bundle will also be rerouted.
The fuel lines on these vehicles may have been misrouted and may contact the "air" check valve. The high temperatures from the "air" check valve could allow it to melt through and damage a fuel line.
Fuel feed hoses may pull out of the crimped coupling at the engine end of the hose assembly.
Fuel return hoses may break at either crimped coupling.
Note: Vehicles equipped with 5.0 litre and 5.7 litre engines. Vehicles may have fuel return hoses which could break at either or both crimped couplings. If a coupling were to separate, fuel leakage and a possible engine compartment fire could result. Correction: A properly crimped fuel return hose will be installed on all involved vehicles.
Note: Vehicles equipped with 2.8.L v6 engines. The fuel feed hoses may pull out of the crimped coupling at the engine end of the hose assembly. This could result in fuel leakage and an engine compartment fire. Correction: A redesigned fuel feed hose will be installed on all involved vehicles.
The hub area of the wheels may not be structurally sound and thus subject to fracture. Consequence of defect: The wheels could separate from the car causing a loss of control. This could result in an accident without prior warning.
Due to undersized grinding at the time of manufacture, the rear brake centre flex hoses could separate from the end fittings when subjected to the pull force required by cmvss 106-74. Tensile strangth test. Such a separation would result in loss of brake fluid and a partial loss of braking action. Should this happen while the vehicle is in motion, at a time when minimum stopping distances are required, a vehicle crash could occur without prior warning.
The involved vehicles do not conform to federal motor vehicle safety standard no. 210, "seat belt assembly anchorages". The non-compliance exists because the rear seat belt anchorages may pull through the underbody of the vehicle if enough force is applied.
Fuel tank ventilator valve in the fuel system may produce a loud and persistent "whistle" during venting of the tank. If the fuel filler cap is removed while this condition exists and the tank is more than 3/4 full, gasoline may be forced out of the filler neck onto bystanders.
On certain vehicles, the seat belt retractors in the rear seating positions contain first lock positions which will not lock when used by smaller passengers. This fails to comply with the requirements of federal motor vehicle safety standard no. 208, "occupant crash protection". Wait, I need to actually translate this into Italian. Here is the translation: Su alcuni veicoli, i meccanismi di avvolgimento delle cinture di sicurezza nei posti posteriori presentano posizioni di primo blocco che non si bloccano quando utilizzati da passeggeri di bassa statura. Ciò non è conforme ai requisiti della norma federale di sicurezza dei veicoli a motore n. 208, "Protezione dei passeggeri in caso di collisione".
**Descrizione del veicolo:** Alcuni veicoli passeggeri non sono conformi ai requisiti della FMVSS n. 208, "Protezione dei occupanti in caso di collisione", e della n. 214, "Protezione in caso di urto laterale". Questi veicoli possono presentare saldature vicino alla cerniera inferiore della portiera del conducente che non rispettano le specifiche.
Veicoli passeggeri equipaggiati con cambio manuale. Il cilindro master della frizione potrebbe essere stato costruito con un anello di ritenuta non corretto.
Nota: Veicoli equipaggiati con motori da 5,7 litri. La valvola di ricircolo dei gas di scarico (EGR) potrebbe guastarsi a causa di corrosione interna. Ciò potrebbe comportare che il veicolo non soddisfi i requisiti di emissione applicabili. Correzione: I concessionari ispezioneranno la valvola EGR per numero di parte e la sostituiranno, se necessario, con una valvola EGR di nuovo design.
Note: Convertible vehicles. These vehicles do not comply with c.M.V.S.S. 209 - seat belt assemblies. The front seat belt retractors may lock-up on slopes less severe than the requirement of the standard. As a result, occupants may not be able to extract and fasten their seat belts until the vehicle is moved to a more level surface. Correction: Dealers will inspect for proper front seat belt retractor position and those found to be improperly positioned will be reinstalled correctly.
These vehicles were manufactured with seat belt retractors out of design position which can cause the retractor to lock-up on slopes less severe than the fmvss requirement. This does not comply with fmvss no. 209, "seat belt assemblies."
Nota: veicoli equipaggiati con cambi automatici 4L60. Il rivestimento del cavo di comando del cambio può staccarsi e impedire l'inserimento della marcia nella posizione corretta; ad esempio, la leva del cambio può trovarsi in posizione P (parcheggio) quando il cambio è in realtà in D (marcia avanti) o R (retromarcia). Questa condizione può causare movimenti imprevisti del veicolo e potrebbe provocare un incidente stradale senza preavviso. Correzione: sui veicoli interessati verrà installata una leva di comando del cambio rivista.
The automatic transmission shift control cable can separate.
These vehicles may not comply with c.M.V.S.S. 209 - seat belt assemblies. - seat belt latch plates may not engage or may do so only after wiggling and/or forcing the latch plate. Correction: Vehicles will be inspected and suspect retractor side safety belt assemblies (which include latch plates) will be replaced if necessary.
The metal latchplates may not engage the buckle assemblies, causing a "no latch" condition. Movement of the seat occupant in this condition could cause latchplate release from the buckle.
On certain vehicles, the parking brake system may contain a non-functional parking brake adjuster. This may result in a gradual loss of parking brake effectiveness as the rear disc pads wear. As a result, the parking brake may not hold the vehicle on a steep incline. If the vehicle is parked with the transmission in neutral or a forward gear, the vehicle may roll away and result in personal injury or property damage. Correction: A new parking brake adjuster will be installed.
Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).