Lettura libera · account gratuito per contribuireErede di Anticars (2000)

Smart Fortwo

1998–2019 · 3 generazioni · 17 difetti documentati · 2 mercati
Generazioni

I bollettini tecnici (TSB) sono istruzioni di riparazione che i costruttori inviano ai concessionari su problemi noti. Non sono richiami di sicurezza, ma spesso confermano un difetto.

Anno modello
MercatoTuttiNA
Fortwo III · 2014–2019
BollettinoModeratoFreniNA

Bollettino

Reclamo Visita ripetuta in officina per vibrazione del veicolo durante la frenata da 60 MPH. NOTA: Sebbene il sintomo sia simile a una vibrazione di pneumatico o ruota, di solito è facilmente riconoscibile che si tratta di un problema diverso a seconda che si verifichi sempre o solo durante la frenata. Causa Sebbene la causa della vibrazione sia molto probabilmente un eccessivo runout laterale del disco o del mozzo/cuscinetto della ruota, è necessario verificare l'intero sistema per individuare altri possibili fattori contribuenti. 1. Danni precedenti da collisione. 2. Tempi di sosta del veicolo eccessivi senza rotazione dei componenti. 3. Runout laterale del mozzo/cuscinetto della ruota. 4. Superficie di accoppiamento della ruota serrata eccessivamente (non è stata seguita la procedura di coppia WIS). 5. Superfici di accoppiamento eccessivamente modificate (verniciate, rigate, piegate, ecc.). Rimedio Leggere l'intero foglio di lavoro allegato prima di eseguire l'intervento. Dopo l'esecuzione, controllare l'ultima pagina ed eseguire il lavoro di conseguenza. NOTA: questo documento non costituisce una preautorizzazione né riguarda in alcun modo la garanzia. È destinato esclusivamente a scopi diagnostici. In caso di dubbi su come procedere OPPURE se il foglio di lavoro è stato eseguito e il veicolo è tornato con lo stesso problema, eseguire nuovamente le misurazioni indicate nel foglio di lavoro e aprire un caso TIPS per il team Body, Chassis and Entertainment.

NHTSA · bollettino del costruttore11038186Anni modello 2017Tradotto automaticamente · originale: ingleseVedi dettagli →
Fortwo III · 2014–2019
BollettinoModeratoSospensioniNA

Bollettino

## Reclamo Rumori nell'area del piantone dello sterzo durante la sterzata. Vedere il file di esempio nell'area allegati: "MRSMSchleifgerusch_SCCMGrindingNoises. MOV". ## Causa In fase di analisi. ## Rimedio Verificare in quale area del piantone dello sterzo si verificano i rumori. I rumori si verificano di preferenza nella parte inferiore, nel vano piedi lato guidatore, oppure nell'area del modulo commutatore dello sterzo (MRSM/SCCM)? Se i rumori si verificano nell'area del MRSM/SCCM, seguire i punti seguenti: allentare le viti del MRSM/SCCM e del volante, riallineare il MRSM/SCCM e serrare nuovamente le viti (vedere WIS). A volte il MRSM/SCCM è sottoposto a tensione e si generano rumori. Se i rumori continuano, scambiare il MRSM/SCCM con quello di un veicolo senza alcun reclamo per rumori. Se i rumori si verificano con il MRSM/SCCM oggetto del reclamo installato nel veicolo senza reclamo (veicolo donatore), il MRSM/SCCM può essere sostituito. Se i rumori si verificano anche nel veicolo del cliente con il MRSM/SCCM del veicolo di riferimento, il MRSM/SCCM non è la causa e non deve essere sostituito. Note: durante il montaggio del MRSM/SCCM, assicurarsi che non si verifichi alcun danno! Se il rumore è dovuto al volante (vedere allegato "LenkradSchleifgerusch_SteeringWheelGrindingNoises.mp4"), utilizzare LI46.10P077313. Smontare e montare tutti i componenti solo in "posizione di marcia diritta" (vedere anche WIS). Fare riferimento a questo LI nella sezione "Note" della richiesta di garanzia!

NHTSA · bollettino del costruttore11038183Anni modello 2019Tradotto automaticamente · originale: ingleseVedi dettagli →
Fortwo III · 2014–2019
BollettinoModeratoSospensioniNA

Bollettino

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

NHTSA · bollettino del costruttore11035005Anni modello 2017Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Fortwo III · 2014–2019
BollettinoModeratoCambioNA

Bollettino

Complaint There are several types of complaint about noises or poor windshield wiper wiping performance: A: Wiper blades squeaking, chattering, shuddering B: The windshield is not wiped completely (streaking) C: During the downward movement water is pulled back onto the windshield from the A-pillar (Figure 1) D: After windshield cleaning, water keeps spraying onto the windshield for several wipe cycles (Figure 2) A1: The windshield and wiper blades are contaminated with residues from car washing facilities, identifiable by the water beading. The resulting differences in the friction values between the wiper blades and the windshield can excite the wiper blades to vibrate. Note: It is mostly wax residue from the washer system, but also water-repellent nano-particle coating for paint and/or silicone-based washer fluid, that could cause this problem. A partially dry windshield also has different friction values, which can likewise result in squeaking of the wiper blades A2: The wiper blades are worn by mechanical damage (wiper lip damaged by ice or insect debris, or deformed by long periods of disuse). A3: Incorrect angle of incidence of the wiper arms to the windshield. Because of this, the rubber lip of the wiper blade may not flip over at the reversal point. Cause B: B1: Wax/ dirt residues on the windshield B2: Wiper blades deformed or worn B3: Downforce of wiper arm not OK (Figure 3) Cause C: Water is pulled back onto the windshield by the differential pressure created as the wiper arm moves downwards. Cause D: Washer water collects in the fastening of the wiper blade and is blown onto the windshield by the airstream over several wipe cycles. Note and supporting information: Wiper blades are wear parts which, even when "not used" for long periods (kept in park position), may become permanently deformed and damaged. Further stresses on the rubber wiper blade arise due to various environmental influences which progressively change the effectiveness of the rubber wiper blade and accelerate the aging process. Due to the natural aging process and wear, the wiper blades should be replaced twice a year, preferably in Spring and Fall (see operator's manual). Remedy Remedy A: A1: Cleaning entire windshield with A 000 986 40 71. A2: Checking water's flow behavior after windshield has been cleaned (see Video 1). If, after cleaning, there are still areas with water beading, then the cleaning process must be carried out again until a rejection reaction is no longer present. Note: On the vehicle in the video (Video 1), water still beads on the bottom left of the windshield. The windshield is still not properly clean, even though it appears to be clean. The windshield is only properly clean when there are no more areas on the windshield where water beads. A3: Replace wiper blades with genuine wiper blades. Important: Only exchange wiper blades if windshield no longer has water-repellent areas Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. Remedy B: B1: Clean windshield with intensive cleaner A 000 986 40 71. Important: Do not clean the wiper blades otherwise the graphite coating will be damaged. B2: Replace wiper blades with genuine wiper blades Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. B3: Check the wiper arm for excessive resistance in the bearing. Restore mobility or replace wiper arm if necessary. Remedy C: Problem inherent in design for which there is no technical remedy. Exception: X204 up to 02/2014. In these vehicles, it is possible to install the design configuration of vehicles as of 02/2014. This includes wiper arms (styled arms) with improved behavior in this respect. It is also necessary to replace the wiper blades because the styled arms feature a Top Lock connection (previously Side Lock).

NHTSA · bollettino del costruttore11032875Anni modello 2017Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Fortwo III · 2014–2019
BollettinoModeratoCarrozzeriaNA

Bollettino

Complaint Headlamp, front fog lamp leaky or fogged. Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system LI82.10-P-078302 Closed ventilation system LI82.10-P-078304

NHTSA · bollettino del costruttore11031580Anni modello 2017Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Fortwo III · 2014–2019
BollettinoModeratoSospensioniNA

Bollettino

Complaint Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts

NHTSA · bollettino del costruttore11019018Anni modello 2017Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Fortwo III · 2014–2019
BollettinoModeratoCarrozzeriaNA

Bollettino

Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged headlamp in the following way: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent, then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: External damage to the headlamp does not present a warranty or goodwill case. 1. Clear fogged/condensed LED headlamps and LED rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). 7. If the condensation has disappeared, nothing else has to be done. Note: If defrosting has been performed, you can skip the first step. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. All vents have to be sealed with sealing compound and the existing diaphragm with the stamp (picture 3 [3]). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged (picture 6). If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation. If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. If the pressure test is not passed, the headlamp is leaky. If the cause cannot be rectified, the headlamp must be replaced. Note: If the headlamp is replaced, no dry packs may be installed on the new replacement headlamp. AR82.10-P-5455WT was created for the pressure test. This AR can be used as a reference manual for all closed headlamps. In the event of an open headlamp system, the vent ducts must be sealed before the pressure test.

NHTSA · bollettino del costruttore11017500Anni modello 2017Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Fortwo III · 2014–2019
BollettinoModeratoCarrozzeriaNA

Bollettino

Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Remedy NOTE: If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for damage. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078896 The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions.

NHTSA · bollettino del costruttore11017496Anni modello 2017Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Fortwo III · 2014–2019
BollettinoModeratoMotoreNA

Bollettino

Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.

NHTSA · bollettino del costruttore11009122Anni modello 2017Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Fortwo III · 2014–2019
BollettinoModeratoCarrozzeriaNA

Bollettino

Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system

NHTSA · bollettino del costruttore11007974Anni modello 2017Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Fortwo III · 2014–2019
BollettinoModeratoCarrozzeriaNA

Bollettino

Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304

NHTSA · bollettino del costruttore11007753Anni modello 2017Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Fortwo III · 2014–2019
BollettinoModeratoCarrozzeriaNA

Bollettino

Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).

NHTSA · bollettino del costruttore11005294Anni modello 2017Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Fortwo III · 2014–2019
BollettinoModeratoSospensioniNA

Bollettino

Noises in the steering column area when steering. Under analysis. Check which area of the steering column the noises occur in. Do the noises tend to occur at the bottom in the driver footwell or do they tend to occur in the area of the steering column switch module (MRSM/SCCM)? If the noises occur in the area of the MRSM/SCCM, work through the following points: - Loosen screws of the MRSM/SCCM and steering wheel, re-align the MRSM/SCCM, and re-fasten the screws (see WIS). Sometimes there is stress at the MRSM/SCCM and noises occur. - If noises continue to occur, swap the MRSM/SCCM into a vehicle without any (noise) complaints. - If the noises occur with the MRSM/SCCM complained about when it is in the vehicle without a complaint (donor vehicle), the MRSM/SCCM can be replaced. - If noises also occur in the customer vehicle with the MRSM/SCCM from the reference vehicle, the MRSM/SCCM is not the cause and must not be replaced. Notes: - When installing the MRSM/SCCM, make sure that no damage occurs! - Only disassemble and mount all component parts in the "straight-ahead position" (see also WIS). - Please refer to this LI in the "Notes" section of the warranty claim!

NHTSA · bollettino del costruttore10249495Anni modello 2019Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Fortwo III · 2014–2019
BollettinoModeratoSospensioniNA

Bollettino

The steering wheel generates grinding noises between the steering wheel and steering column switch module during steering maneuvers See example file in the attachments area: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises.mp4 The plastic cover on the back of the steering wheel is not positioned correctly and may therefore rub against the steering column switch module Please use the following noise files for the damaged part analysis: 1. Grinding noise | pot. cause: steering wheel | see attachment: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises. mp4 2. Creaking/cracking noise | pot. cause: steering column switch module | see attachment: MRSM-Schleifgerusch_ SCCM-GrindingNoises.MOV If the noise is due to the steering column switch module, please use LI46.10-P-077314. Check for grinding areas on the steering wheel: Please check the covers on the rear for protrusion and, if necessary, remount. 1. Mask off openings on back of steering wheel with adhesive tape 1. Mark the back of the steering wheel with colored chalk (see Picture 1) 2. Mount steering wheel on steering column switch module and turn the steering wheel from left lock to right lock ten times. 3. The chalk will now have disappeared in the areas where there is rubbing (see Picture 2) Warning: Ensure that no cables and visible areas of the steering wheel are damaged. The abrasive excess material on the back of the steering wheel must be carefully removed with a Dremel tool. Tip: You will need to remove approx. 0.1 mm to 0.3 mm of material (example: Picture 3) Make sure that none of the ground-off material gets into the steering wheel. After removing the material, clean the entire back of the steering wheel with a 1% soap solution.

NHTSA · bollettino del costruttore10249482Anni modello 2019Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Fortwo III · 2014–2019
BollettinoModeratoSospensioniNA

Bollettino

Installation position of suspension springs at rear axle

NHTSA · bollettino del costruttore10136106Anni modello 2017Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Fortwo III · 2014–2019
BollettinoModeratoFreniNA

Bollettino

Brake pedal/carpet seal does not fit properly

NHTSA · bollettino del costruttore10136015Anni modello 2017Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Fortwo III · 2014–2019
BollettinoModeratoCambioNA

Bollettino

Slight oil leakage at single stage transmission

NHTSA · bollettino del costruttore10135830Anni modello 2014Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Fortwo III · 2014–2019
BollettinoModeratoSospensioniNA

Bollettino

Creaking, grating or grunting noise while steering audible in the steering gear area. The noise can be transferred through the steering gear into the interior. The noise occurs, in particular, at high temperatures, e.g. in the summer.

NHTSA · bollettino del costruttore10167004Anni modello 2017Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Fortwo III · 2014–2019
BollettinoModeratoSospensioniNA

Bollettino

Creaking, grating or grunting noise when steering

NHTSA · bollettino del costruttore10135956Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Fortwo III · 2014–2019
BollettinoModeratoAbitacoloNA

Bollettino

The airbag indicator lamp in the instrument cluster remains on.

NHTSA · bollettino del costruttore10135947Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Fortwo III · 2014–2019
BollettinoLieveCarrozzeriaNA

Bollettino

Denuncia Rumore metallico proveniente dalla zona degli altoparlanti nelle portiere. Causa In fase di analisi. Rimedio Per restringere la causa, rimuovere innanzitutto il rivestimento della portiera. Se il rumore continua a verificarsi anche con il rivestimento della portiera rimosso, proseguire la diagnosi concentrandosi sull'altoparlante e, se necessario, aprire un caso TIPS con un video informativo come allegato. Nota: fare riferimento a questo documento nella richiesta di garanzia e, una volta completata la diagnosi, selezionare il codice di danno in base al componente che causa il problema. Se il rumore si interrompe quando il rivestimento della portiera viene rimosso, procedere in conformità con LI72.10P067691. Informazioni In questo caso, non utilizzare un codice di danno per gli altoparlanti nella richiesta di garanzia!

NHTSA · bollettino del costruttore11038217Anni modello 2017Tradotto automaticamente · originale: ingleseVedi dettagli →
Fortwo III · 2014–2019
BollettinoLieveCarrozzeriaNA

Bollettino

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

NHTSA · bollettino del costruttore11036101Anni modello 2017Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Fortwo III · 2014–2019
BollettinoLieveElettronicaNA

Bollettino

Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) vehicles listed below, an activation of the Malfunction Indicator Lamp (MIL) may occur due to sporadic jamming of the fuel tank ventilation valve. As a result, we have decided to extend the warranty on the fuel tank ventilation valve from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 10 years/120,000 miles. This extended warranty applies to the aforementioned condition that necessitates the servicing and/or replacement of the fuel tank ventilation valve under the standard warranty terms and conditions. The extended warranty is applicable to the following vehicles:

NHTSA · bollettino del costruttore11031818Anni modello 2017Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Fortwo III · 2014–2019
BollettinoLieveElettronicaNA

Bollettino

In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (MBUSA) hereby notifies you of additional benefits regarding your vehicle ownership. What is the concern? MBUSA has determined that on certain Model Year 2016-2017 Smart fortwo (453 platform) vehicles, the secondary air injection system combination valve may not close completely under certain climate conditions due to condensation in the exhaust system. An open combination valve could lead to an activation of a Malfunction Indicator Lamp (MIL), which could cause the vehicle to fail a state smog inspection. What is the outcome? MBUSA is extending the coverage for the combination valve of the secondary air injection system from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years / 150,000 miles (whichever occurs first), which applies to the vehicle regardless of ownership. Any repairs under this warranty extension must be performed by an authorized Mercedes-Benz dealership. Your preferred authorized Mercedes-Benz dealer will perform a diagnosis to determine if the secondary air injection system combination valve is malfunctioning. If diagnosis confirms that your vehicle has the issue, the repair will be performed at no cost to you. This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet.

NHTSA · bollettino del costruttore11031814Anni modello 2016–2017Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Fortwo III · 2014–2019
BollettinoLieveCarrozzeriaNA

Bollettino

In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA (MBUSA) is extending the coverage for the change-over valve on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 10 years / 120,000 miles (whichever occurs first), and applies to the vehicle regardless of ownership. Why the warranty extension? On certain Model Year 2016-2017 smart vehicles, the change-over valve which is responsible for the operation of the heating shut-off valve within the coolant circuit, could corrode internally due to water intrusion. The internal corrosion might then prevent proper operation of the heating shut-off valve. Any repairs under this warranty extension must be performed by an authorized Mercedes-Benz smart dealership. If your preferred authorized Mercedes-Benz smart dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be performed at no cost to you. This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet.

NHTSA · bollettino del costruttore11031811Anni modello 2016–2017Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Meno recenti →

Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).