閲覧無料 · 投稿は無料アカウントでAnticars(2000年)の後継

Audi R8

2006–2024 · 1 世代 · 不具合1件 · 3市場
世代
すべての世代R82006–20241231083

技術サービス通報(TSB)は、既知の不具合についてメーカーが販売店に送る修理指示です。安全リコールではありませんが、不具合の裏付けになることがよくあります。

年式
技術通報重大エンジンNA

技術通報

Supersedes Technical Service Bulletin Group 01 number 12-57 dated October 29, 2012. Noises/inconsistent engine operation after cold start during the catalyst heating phase. The customer may interpret this engine roughness as misfiring. To comply with the legal requirements on exhaust gas emissions according to the LEV-1 and LEV-2 standards, a high exhaust gas quality must be ensured. The necessary catalyst only operates at a temperature over 300C (572F). To achieve this, the catalyst is heated up. The catalyst heating phase is achieved by a late ignition angles and by introducing additional fresh air to the exhaust valves (secondary air system). Late ignition angles make sure that the exhaust gas from the cylinders has a higher temperature. This exhaust gas includes fuel that is un-burnt, and was deliberately injected into great quantities. The secondary air system adds fresh air to the exhaust gas as it leaves the cylinder and the extra fuel is burnt. As a result, the temperatures of the exhaust gas and of the catalyst increase quickly. The afterburning in the exhaust manifold before the catalyst changes the sound characteristic of the engine. This heating-up of the catalyst, including afterburning, is normal and has no effect on the service life of the engine. During this catalyst heating phase, the engine has increased idle speed, may have increased vibrations, and has a different sound characteristic. Depending on conditions, the time of the catalyst heating phase varies.

NHTSA · メーカー通報10123969モデルイヤー 2011–2012原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報重大エンジンNA

技術通報

Supersedes Technical Service Bulletin Group 01 number 12-51 dated July 18, 2012. Noises/inconsistent engine operation after cold start during the catalyst heating phase. The customer may interpret this engine roughness as misfiring. To comply with the legal requirements on exhaust gas emissions according to the LEV-1 and LEV-2 standards, a high exhaust gas quality must be ensured. The necessary catalyst only operates at a temperature over 300C (572F). To achieve this, the catalyst is heated up. The catalyst heating phase is achieved by a late ignition angles and by introducing additional fresh air to the exhaust valves (secondary air system). Late ignition angles make sure that the exhaust gas from the cylinders has a higher temperature. This exhaust gas includes fuel that is un-burnt, and was deliberately injected into great quantities. The secondary air system adds fresh air to the exhaust gas as it leaves the cylinder and the extra fuel is burnt. As a result, the temperature of the exhaust gas and of the catalyst increases quickly. The afterburning in the exhaust manifold before catalyst changes the sound characteristic of the engine. This heating-up of the catalyst, including afterburning, is normal and has no effect on the service life of the engine. During this catalyst heating phase the engine has increased idle speed, may have increased vibrations, and a different sound characteristic. Depending on conditions the time of the catalyst heating phase varies.

NHTSA · メーカー通報10122803モデルイヤー 2011–2012原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度エンジンNA

技術通報

This bulletin provides information for all gasoline engines when the MIL is on; DTC P240700 is stored - Fuel leak detection pump.

NHTSA · メーカー通報11039214モデルイヤー 2023原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度エンジンNA

技術通報

This bulletin provides information when the fuel tank cap seal is leaking; DTC P044200, P045600 and/ or P00EF00 in stored in the ECM.

NHTSA · メーカー通報11034668モデルイヤー 2023原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度エンジンNA

技術通報

This bulletin provides information regarding UV leak additive for finding oil leaks.

NHTSA · メーカー通報11028398モデルイヤー 2012原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度エンジンNA

技術通報

This bulletin provides information when the fuel tank cap seal is leaking; DTC P044200, P045600 and/ or P00EF00 in stored in the ECM.

NHTSA · メーカー通報11025354モデルイヤー 2023原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度エンジンNA

技術通報

This TSB provides information when the fuel tank cap seal is leaking, DTC P044200, P045600, and/or P00EF00 stored in ECM.

NHTSA · メーカー通報11022688モデルイヤー 2023原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度エンジンNA

技術通報

This bulleitn provides information regarding UV Leak additive for finding oil leaks.

NHTSA · メーカー通報11022633モデルイヤー 2012原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度エンジンNA

技術通報

この保留サービスソリューション(PSS)では、MILが点灯している場合に、技術者がPSSデータベースに記録を登録することを求めています。対象は、Evalリーク検知ポンプ回路、DTC240700です。

NHTSA · メーカー通報11009316モデルイヤー 2023自動翻訳 · 原文:英語詳細を見る →
技術通報中程度エンジンNA

技術通報

This Pending Service Solution (PSS) requests that technicians enter a PSS record in instances where DTC P240700 Evap leak detection pump circuit is stored.

NHTSA · メーカー通報11005851モデルイヤー 2023原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度エンジンNA

技術通報

This Pending Service Solution (PSS) requests that technicians enter a PSS record in instances where DTC P240700 Evap leak detection pump circuit is stored.

NHTSA · メーカー通報11002215モデルイヤー 2023原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度エンジンNA

技術通報

This Pending Service Solution (PSS) requests that technicians enter a PSS record in instances where DTC P240700 Evap leak detection pump circuit is stored.

NHTSA · メーカー通報11002115モデルイヤー 2023原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度エンジンNA

技術通報

This Pending Service Solution (PSS) requests that technicians enter a record in the PSS Database in instances where the MIL is on and DTC P240700 is stored; Evap leak detection pump circuit.

NHTSA · メーカー通報10253248モデルイヤー 2023原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度エンジンNA

技術通報

This bulletin contains instructions for an oil leak that is due to excessive sealant used in a previous repair.

NHTSA · メーカー通報10153121モデルイヤー 2012原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度エンジンNA

技術通報

リフト上点検セクション: 取り外し 「ELSAで冷却水リザーバーキャップの圧力試験を実施する -> VIN番号を入力 -> 修理マニュアル Engine -> 4-Cylinder Direct Injection 1.8L; 2.0L 4V TFSI Engine (Generation III) -> 19 Cooling System -> Coolant System/Coolant -> Cooling System, Checking for Leaks -> Pressure Relief Valve in Cap, Checking」。文書「Cooling System, Checking for Leaks」では、手順「Pressure Relief Valve in Cap, Checking」のみを実施すること。

NHTSA · メーカー通報10120803モデルイヤー 2017自動翻訳 · 原文:英語詳細を見る →
技術通報中程度エンジンNA

技術通報

Supersedes Technical Service Bulletin Group 10 number 13-10 dated September 5, 2013. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these metal debris pieces are not removed prior to the installation and operation of the replacement engine, they could be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.

NHTSA · メーカー通報10119945モデルイヤー 2012原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度エンジンNA

技術通報

Supersedes Technical Service Bulletin Group 24 number 12-27 dated April 23, 2012. MIL is illuminated. Irregular engine performance. R8 Intake Air Hose leaking.

NHTSA · メーカー通報10124951モデルイヤー 2011–2012原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度エンジンNA

技術通報

A small amount of dry or crusted coolant is seen on the coolant pump housing. The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. The dry coolant marks are normal.

NHTSA · メーカー通報10124868モデルイヤー 2012原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度エンジンNA

技術通報

Supersedes Technical Service Bulletin Group 10 number 10-02 dated September 14, 2010. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the vehicle's engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these pieces are not removed prior to the installation and operation of the replacement engine, the pieces may be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.

NHTSA · メーカー通報10121324モデルイヤー 2012原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報軽微エンジンNA

技術通報

This bulletin provides a statement regarding the bottleneck of supply for VW approved oil types VW 504.00 and VW 507.00.

NHTSA · メーカー通報11035854モデルイヤー 2012原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報軽微エンジンNA

技術通報

This bulletin provides information when DTC B105A1A, B103E25 is stored in 0017; fuel tank level implausible.

NHTSA · メーカー通報11035829モデルイヤー 2023原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報軽微エンジンNA

技術通報

This bulletin provides information when DTC B105A1A, B103E25 is stored in 0017; fuel tank level implausible.

NHTSA · メーカー通報11035828モデルイヤー 2023原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報軽微エンジンNA

技術通報

This bulletin provides informaiton when the engine is not running smoothly, misfiring.

NHTSA · メーカー通報11034728モデルイヤー 2012原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報軽微エンジンNA

技術通報

This bulletin provides information when there is increased oil consumption; >0.5ltr/1000 km.

NHTSA · メーカー通報11034657モデルイヤー 2023原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報軽微エンジンNA

技術通報

This bulletin provides information when there is increased oil consumption; >0.5ltr/1000 km.

NHTSA · メーカー通報11027356モデルイヤー 2023原文(英語)で表示中 · 翻訳待ち詳細を見る →
古いもの →

出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)、国土交通省(日本、公共データ利用規約1.0)、韓国国土交通部(car.go.kr)。