HVAC refrigerant leakage suspected or reports of a damp/musty smell within the cabin - Diagnosis guidelines. Condition HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin. - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs particularly TPI 2062622/- - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident.
HVAC refrigerant leakage suspected Or reports of a damp/musty smell within the cabin - Diagnosis guidelines. Customer statement / workshop findings: HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin Note: For this scenario please see the pre requisites below - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs particularly TPI 2062622/- - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident. In the event that HVAC cleaning products are required, these MUST be sourced locally. Before using the cleaner the operative must inform the customer of the product which will be used, a neutral fragrance cleaner should be used as the customer may not like the smell of the cleaner should a fragranced product be used Please ensure all supporting information is included within the DISS query when requesting permission to clean the HVAC system including clear photographs and/or videos showing the reported issue, should the required information not be supplied the warranty claim could be cancelled.
HVAC refrigerant leakage suspected Or reports of a damp/musty smell within the cabin - Diagnosis guidelines. Customer statement / workshop findings: HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin Note: For this scenario please see the pre requisites below - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs particularly TPI 2062622/- - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident.
PSIS 750600B0001 Wiring modification for seat belt pre-tensioner buckle switches. Customer statement / workshop findings: This PSIS has been issued to inform parts and service personnel of a wiring modification to the buckle switches on the seat belt pre-tensioners. If a vehicle enters the workshop with an owner complaint of airbag warning light illumination and codes are stored for; Drivers seat belt buckle switch resistance undefined intermittent Passenger seat belt buckle switch resistance undefined intermittent Then the following modification to the wiring should be carried out. Technical background: Heritage PSIS (Product Support Information Sheet). Reference attached PDF for details
PSIS 750600B0001 Wiring modification for seat belt pre-tensioner buckle switches. Condition This PSIS has been issued to inform parts and service personnel of a wiring modification to the buckle switches on the seat belt pre-tensioners. If a vehicle enters the workshop with an owner complaint of airbag warning light illumination and codes are stored for; Drivers seat belt buckle switch resistance undefined intermittent Passenger seat belt buckle switch resistance undefined intermittent Then the following modification to the wiring should be carried out. Technical Background Heritage PSIS (Product Support Information Sheet). Reference attached PDF for details
Brake noise identification. Customer statement / workshop findings: Noise complaint from the braking system. Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Technical background Brake noises can be attributed to many causes. Eight of the most common causes are: - Brake discs or pads are close to their wear limit. - New brake pads and/or discs have not been properly bedded in after installation. - Aftermarket pads or discs are installed. - There is debris such as small stones, grit, road salt or sand between the brake disc and pad. - Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time (Figure 1).
Poor Engine Running Complaints (Misfires) Petrol Engines Only. Customer statement / workshop findings: Poor engine running, reduced power, engine warning lamp illuminated. Technical background: Technical Product Information (TPI) to assist Retailers when diagnosing poor engine running or misfire. Measure: The following TPI should be carried out sequentially to ensure the root cause and analysis of the concern are identified without unnecessary work or repetitive actions taking place.
Electrical switch replacement guidelines. Customer statement/workshop findings: Electrical switch suspected as defective This TPI is not applicable to suspected faulty control units or any component related to the passive restraint system in particular the airbag system Technical background: Prior to replacing an electrical switch refer to the Measure section of this TPI
Brake noise identification. Customer statement: Noise complaint from the braking system. Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Technical Background: Brake noises can be attributed to many causes. Eight of the most common causes are: 1. Brake discs or pads are close to their wear limit. 2. New brake pads and/or discs have not been properly bedded in after installation. 3. Aftermarket pads or discs are installed. 4. There is debris such as small stones, grit, road salt or sand between the brake disc and pad. 5. Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time (Figure 1).
Electrical switch replacement guidelines Customer statement / workshop findings: Electrical switch suspected as defective This TPI is not applicable to suspected faulty control units or any component related to the passive restraint system in particular the airbag system Technical background: Prior to replacing an electrical switch refer to the Measure section of this TPI
Telephone Functionality Complaint - Minimum Standards Required For Analysis Of Concerns. Customer statement / workshop findings: The feedback method within this TPI is required should a complaint of telephone functionality and/or quality be reported. Technical background: The minimum standards check list document within the Measure section is required to capture an accurate description of customer telephone issues.
All Vehicle Variants - Spurious DTC List. Customer statement / workshop findings: Customers will not be aware of any fault codes Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle Technical background: The operative should refer to the Bentley Hub referencing TPI 2053177/- The document (loaded onto the Hub) contains all of the current known Spurious DTCs for all vehicle variants Should a particular TPI be listed as Archived, the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions within TPI 2053177/- regarding the DTC description and actions which should be conducted (if any).
Speaker Replacement - Diagnostic Checks Technical Background: -There have been instances where door speakers have been changed under warranty for the complaint of sound distortion, yet when tested by ourselves and the supplier, no fault could be found with the returned unit.
Telephone Functionality Complaint- Minimum Standards Required For Analysis of Concerns Customer Statement: -The feedback method within this TPI is required should a complaint of telephone functionality and/or quality be reported.
Speaker Replacement - Diagnostic checks. Customer statement / workshop findings: Audio output from speakers is distorted Technical background: There have been instances where door speakers have been changed under warranty for the complaint of sound distortion, yet when tested by ourselves and the supplier, no fault could be found with the returned unit. Production change: All speakers are subjected to a dynamic test and the individual results recorded for future reference
Telephone Functionality Complaint - Minimum Standards Required For Analysis Of Concerns. Customer statement / workshop findings: The feedback method within this TPI is required should a complaint of telephone functionality and/or quality be reported. Technical background: The minimum standards check list document within the Measure section is required to capture an accurate description of customer telephone issues.
Bentley: Fuel filler caps. There are the standard fitted black plastic fuel filler cap for mulsanne/arnage and the jewel fuel filler cap fitted for continental. Black plastic fuel filler cap not to be placed on continental and jewel fuel filler cap not to be placed on mulsanne/arnage. This will reduce fuel tanks capability to breath and vent correctly. No model years were listed. *pe
出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)、国土交通省(日本、公共データ利用規約1.0)、韓国国土交通部(car.go.kr)。