0Replacement of Steering Gear Due to Accident Damage. INFORMATION The steering gear does NOT have to be replaced if: ? There is no visible damage to front axle parts such as spring struts, hubs or spindles, control arms or wishbones, thrust or tension rods or stabilizers performing a locating function, steering drop arms or Pitman arms, track rods or drag links, tie rods, front axle subframe, steering column, and attachment points for suspension components to body. ? There is no binding or increase in turning effort when operating the steering gear from lock to lock with engine off. ? The impact has not caused the wheel alignment to become not adjustable within specified tolerances using normal adjustment procedures. The steering gear MUST be replaced if: ? There is visible damage to the steering gear, including blackening or discoloration of the housing from fire damage. ? Electric steering gear (EPS) version: Examine the control unit with all plug connections for damage and hairline cracks. ? There is any permanent deformation or cracks on: ? Wheel rims in the event of a negative result from the wheel/axle alignment check ? Spring struts, steering stubs, wheel carriers ? Wishbones ? Struts, trailing links or the anti-roll bar with this function ? Body side screwing/attachment points for wheel guide control components ? Front axle support ? Pitman arms https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/21101.1.M320405....3/2/2015 Page 2 of 2 ? Tie rods ? Steering box fixtures ? Steering column The steering column MUST be replaced if visibly damaged, deformed or broken. If a recommended replacement with the criteria described above is refused by the customer or insurance company, this should be noted in the repair order and signed by the refusing party.
Rattling/knocking noise from the front axle at low speeds of less than 15 mph. The noises are induced by driving over rough road surface or by brake operation. The noises occur during straight ahead driving or cornering.
After replacement of the Integrated Braking system (IB)/Power Brake the total distance covered might belower than when handed over to the workshop for the repair.
Due to an implementation error in various OBD diagnostics in the vehicle's control units, in very rare cases itmay happen that stored fault memory codes (DTCs) and the MIL (warning light) are not automaticallydeleted even though the underlying malfunction has already been rectified. This does not comply with the statutory OBD specifications.
It was determined that your vehicle was fitted with a brake booster that potentially has a faulty hydraulic valve. This may result in a modified pedal feel and a sporadic red Check Control message. The brake booster should be replaced.
Several complaints are possible: Vehicle does not start Gear cannot be engaged Various Check Control Messages Malfunction indicator lamp (MIL) on Several Check Control messages are possible: It is possible to continue driving. High-voltage system. You can continue driving. Drivetrain. Restart not possible. Drivetrain fault. Call Roadside Assistance. Drivetrain failure. Information: Total error of vehicle. The following fault memory entries are stored in the CCU: D796D9 - Message (- 0x91) not up-to-date, receiver CCU, transmitter EME D796DC - No message (- 0x91), receiver CCU, transmitter EME D796D8 - No message (- 0x91), receiver CCU, transmitter EME Other fault codes below may be stored in the EGS BA09B8 Inverter, Voltage Sensor, 5V HV AUX: Out of range or open connection detected BA0A45 ECU internal: Internal error of the synchronous serial data bus. Additional fault memory entries are possible. Similar fault memory entries indicating a missing EMEmessage (Traction E-Machine Electronic) can also be stored in other control units.
Various external influences can cause premature aging of the tension strut hydro-mount elastomer; which can lead to cracks in the material, and leakage.
The right rear drive shaft may not have been manufactured correctly during production and may break. In the event of a fault, you will hear significant noises in the area of the rear axle and the driving performance will be noticeably reduced. At the same time, warning lights and Check Control messages will be shown on the Central Display.
The wheel bearing and the brake disc are not correctly aligned; are not concentric (circled). When applicable work is being performed, it is therefore difficult to remove the wheel bolts from, or fasten them into the wheel bearing hub.
The seat lumbar system Massage will not function if the module needs to be initialized. This can occur toeither the drivers and/or passenger side seat. Here is a list of possible faults: Seat pneumatics module front right SPNM _ VR 025908 - SPNMVR: Control unit is not coded 02590B - SPNMVR: Control unit is not encoded for the vehicle 806927 - SPNMVR: Installation location not taught in Seat pneumatics module front left SPNM _ VL 025308 - SPNMVL: Control unit is not coded 02530B - SPNMVL: Control unit is not encoded for the vehicle 8067A7 - SPNMVL: Installation location not taught in Seat Module Driver FAS SMFA 80301E - No seat adjustment because of engine start conditions Seat Module Passenger BFS SMBF 802C1E - No seat adjustment because of engine start conditions Seat Module Drivers Side Rear FAH SMFAH 802E1E - No seat adjustment because of engine start conditions Seat Module Passenger Side Rear BFH SMBFH 802A1E - No seat adjustment because of engine start conditions
After programming from the I-Levels between 24-03-505 and lower than 24-03-540 to I-Level 24-11-530 or higher, the following CCM may be displayed: CCM-2525: Brake system. Drive at moderate speed
The air line on the air suspension supply system may not be properly installed. In the event of a fault, residual pressure is maintained in the struts and corresponding check control message.
The air line on the air suspension supply system may not be properly installed. In the event of a fault, residual pressure is maintained in the struts and corresponding check control message.
After replacement of the Integrated Braking system (IB)/Power Brake the total distance covered might be lower than when handed over to the workshop for the repair.
BMW AG has decided on a service campaign for certain vehicles from the G0x, G12 and G20 series. Please have the starter motor checked and, if necessary, replaced in the vehicles concerned (according to the vehicle identification number selection) if possible before vehicle delivery. If vehicles have already been delivered, please have the measure carried out the next time the vehicles enter the workshop. A bolting fault on the long bolt screws can cause the magnets in the starter motor to twist. As a result, the power of the starter motor decreases. As a result, the engine does not start.
After replacement of the Integrated Braking system (IB)/Power Brake the total distance covered might be lower than when handed over to the workshop for the repair.
Only fuel nozzles with the recommended specified diameter for diesel engine passenger vehicles can beinserted into the filler neck. Most fuel stations have their diesel fuel pumps fitted with this recommendeddiameter fuel nozzle. However, if the vehicles filler-neck misfuelling protection system has been disabled, or the incorrectdiameter fuel nozzle has been installed on the diesel fuel pump, the vehicles diesel fuel system can becontaminated by filling the diesel engine vehicle with gasoline. If the diesel fuel system has been contaminated with gasoline, follow the repair guidelines below:
Due to an installation error, the crankshaft sensor connector may not have been properly locked. In very rare cases, the plug connection may become disconnected. If no signal is sent by the crankshaftsensor, the engine will switch to emergency operation and a Check Control message will occur.
出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)、国土交通省(日本、公共データ利用規約1.0)、韓国国土交通部(car.go.kr)。