シートベルト
対象車両:サンバイザーに設置されたエアバッグラベルを装備した一部の乗用車は、連邦自動車両安全基準第208号「乗員衝突保護」に適合していません。これらの車両は、メッセージ領域が30 cm未満であり、同基準の要件を満たしていません。
🔔 無料アカウントを作成して Buick センチュリー (すべての世代) のメール通知を受け取る
対象車両:サンバイザーに設置されたエアバッグラベルを装備した一部の乗用車は、連邦自動車両安全基準第208号「乗員衝突保護」に適合していません。これらの車両は、メッセージ領域が30 cm未満であり、同基準の要件を満たしていません。
Vehicle description: Passenger vehicles. Some of these vehicles exhibit a condition in which the driver side impact air bag inflator separates from the air bag module during deployment.
Vehicle description: Passenger vehicles. The clamp that secures the flexible fuel fill hose to the metal fill tube may be loose and could separate.
Some of these vehicles with the key in the "on" position, exhibit a condition in which the antilock brake system (abs) motor shorts to its case and grounds through a flexible brake fluid pipe.
Note: Vehicles located in ontario(4) and british columbia(1). These vehicles may have an under torqued right hand front spindle nut. If this nut were to fall off, the wheel could separate from the vehicle possibly resulting in a crash without prior warning. Correction: Vehicles will be inspected and if the right hand front spindle nut is under torqued, the wheel bearing assembly and nut will be replaced.
The right hand spindle nut was not properly tightened during assembly. This can cause premature wheel bearing failure and over time, the spindle can fracture.
The power door lock relay on these vehicles can short internally due to water intrusion. This condition may result in a vehicle fire. Correction: Power door lock relay and any corroded terminals will be replaced. In addition, the new relay will be relocated to an area where water intrusion is less likely
Water intrusion can cause a short circuit in the power door lock assembly.
The power seat or recliner wiring harness can be pinched or can chafe on the seat frame or spring support rod, wearing through the wire insulation and causing an electrical short.
The fuel feed hose could leak at the coupling on the engine end of the hose assembly. This condition could allow fuel to leak into the engine compartment and possibly result in an engine compartment fire. Correction: Fuel feed hose assembly will be inspected and replaced if necessary with a new hose assembly.
Fuel feed hose could leak at the coupling on the engine end of the hose assembly.
Front suspension lower control arm bracket could develop metal cracks.
オンタリオ州およびケベック州の一部の車両では、リアブレーキのバッキングプレートにあるパイロットホール(位置決め穴)が過度に拡大されている場合、ホイールシリンダーが回転するおそれがあります。その結果、リアブレーキのブレーキフルードが漏れ、リアブレーキの制動能力が失われる可能性があります。これにより制動距離が長くなり、衝突事故につながるおそれがあります。注:対象はオンタリオ州およびケベック州の車両のみです。
The generator "bat" terminal located on the rectifier end frame may contact the carburetor fuel inlet pipe. Consequence of defect: The "bat" stud may rub through the terminal boot and contact the fuel pipe which could result in an underhood fire and cause burn injuries to the occupant.
Excessive enlargement of the wheel cylinder pilot hole in the rear brake backing plate could allow the wheel cylinder to rotate and cause loss of brake fluid. Consequence of defect: A loss of brake fluid leads to loss of rear brake action, creating the potential for an accident. Front brakes would remain operational.
2.5リッターエンジン搭載車両の場合。スロットルボディ噴射燃料供給パイプの接続部で燃料漏れが発生する可能性があり、フード下火災の可能性があります。
燃料システムはスロットルボディ噴射燃料供給パイプの接続部で漏れる可能性があります。欠陥の結果:この漏れはフード下火災を引き起こし、乗員区画に広がり、乗員に火傷によるけど傷を負わせる可能性があります。
The axle retaining "c" clip in the differential may dislodge and allow the axle, wheel and brake drum to separate from the vehicle when subjected to side forces. Axle separation could result in loss of vehicle control and possible crash.
The brake proportioner valves may break and separate from the master cylinder during braking. This will result in a loss of brake fluid and a partial loss of braking action
The rear brake hoses were not fully seated into their fittings when the fittings were crimped onto the hose at the time of manufacture. Hose failure would cause loss of brake fluid and partial loss of braking action thereby increasing stopping distance.
Under certaain conditions, the hose clamps on the fuel tank filler pipe and fuel tank filler vent pipe could fracture. The fracture of these clamps could cause fuel leakage at any of the four pipe to hose connections. Leakage can occur during refueling, or while driving, if the fuel tank is above 3/4 full.
Under certain conditions the hose clamps on the fuel filler pipe and fuel tank filler vent pipe could fracture. This could cause seepage of fuel at any one of the four pipe to hose connections when the fuel tank is above 3/4 full creating the possibility of fire.
"tx" heavy duty wheels may have been manufactured with laminated steel. The wheel disc may fracture and the wheel and tire could partially or completely separate from the vehicle.
特定の乗用車は、連邦自動車安全基準第108号「ランプ、反射装置および関連装備」の要件に適合していない。これらの車両の一部は、頭上標識の照明要件を満たしていない。
定められた要件に適合していない車両が一部存在します。CMVSS 101 - 操作装置および表示装置の位置と識別に適合していません。これらの車両では、オイル圧が低い、または全くない状態になっても「オイル警告灯」が点灯しない状態が発生します。是正措置:販売店が新しいキャリブレーションソフトウェアで車両のPCMを再書き込み(リフラッシュ)します。
出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)、国土交通省(日本、公共データ利用規約1.0)、韓国国土交通部(car.go.kr)。