On certain passenger vehicles equipped with 3800 V6 (L36) engines and certain Delphi fuel pressure regulators, the regulators have a much higher than usual rate of fuel leaks. A leak can allow fuel to enter the intake manifold through a vacuum line. If the engine does not start when cranked, the fuel from the leaking regulator and a mistimed spark can cause a backfire.
These vehicles may exhibit a backfire during engine starting that can cause breakage of the upper intake manifold. This can cause a no-start condition and possibly an engine compartment fire. Also, if a person was in the vicinity of the intake manifold when the hood was open, and this backfire condition occurred, it could result in personal injury. Correction: The pcm (powertrain control module) will be reflashed with new programming software.
The upper transaxle oil cooler hose could pull out of the crimped coupling at the transaxle end of the line assembly. If this coupling were to separate, transaxle oil would spill into the engine compartment and, in the presence of an ignition source, a fire could occur. Correction: Dealers will install a new upper transaxle oil cooler line on all involved vehicles.
The brake hydraulic unit mounting bolts on these vehicles may have been undertorqued. This condition could cause increased brake pedal travel and/or poor pedal feel if the attachment loosens. In addition, this condition could eventually lead to separation of the brake hydraulic unit from its mounting brackets resulting in brake loss and a possible vehicle crash. Correction: Hydraulic unit mounting bolts will be replaced on involved vehicles.
Under a high resistance load, the in-line fuseable link located in the area of the plastic windshield washer bottle bracket, may melt down and ignite the bracket. This could result in an engine compartment fire without prior warning. Correction: Windshield washer bottle bracket will be replaced on affected vehicles.
Vehicles may have been assembled with a rubber fuel return hose which could allow a slow fuel leak while the engine is running. Under certain conditions this could result in a fire which could spread to the passenger compartment and cause burn unjuries to occupants.
The power brake vacuum hoses may fail to conform to federal motor vehicle safety standard no. 106, "brake hoses". The material used in the hoses will not perform according to specifications. The purpose of this regulation is stated as, "to reduce death and injuries occurring as a result of brake system failure from pressure or vacuum loss due to hose assembly rupture".
Vehicle description: Passenger vehicles. These vehicles do not conform to the requirements of fmvss no. 108, "lamps, reflective devices, and associated equipment." the head lamp adjustment device horizontal adjuster may not move the head lamp reflector when the shaft is rotated in a normal manner during aiming.
On certain vehicles, the inner tie rod nuts may be loose, which could result in separation of a tie rod. Separation of a tie rod could cause unexpected steering input in some maneuvers and could cause a crash without prior warning. Correction: Dealers will check the torque of the inner tie rod nuts and if necessary, adjust the vehicle toe-in and tighten the inner tie rod nuts to the specified torque.
Certain vehicles do not comply with the requirements of CMVSS 102 - Transmission Shift Control Sequence. A retaining clip which secures the manual valve to the linkage of the transmission detent lever, may become loose and allow the link to become disconnected from the manual valve. If the link disconnects, the driver's indicated 'PRNDL' state may differ from the hydraulic state of the transmission. This does not affect the 'PARK' position, but if a driver selects 'DRIVE' and the transmission is actually in 'REVERSE', a crash could occur without warning. Correction: Dealers will replace the manual valve/link assembly with a replacement manual valve/link kit, featuring a spring-type fastener.
Vehicle description: Passenger vehicles equipped with 4t65e automatic transmissions. These vehicles fail to conform to the requirements of fmvss no. 102, "transmission shift lever sequence." a retaining clip, which secures the manual valve to the linkage of the transmission detent lever, can become loose under a combination of possible driver shifting maneuvers and allow the link to become disconnected from the manual valve.
These vehicles do not comply with c.M.V.S.S. 1101 - emission device. Improper calibration of the powertrain control module (pcm) can result in uncontrolled spark knock, setting an mil (malfunction indicator lamp), misfire, rough idle, audible knock and/or possible engine damage. Correction: Vehicle pcm will be reflashed with new calibration softwear.
Certain vehicles may not comply with CMVSS 209 - Seatbelt Assemblies. Vehicles may have been assembled with one or more incorrect seat belt and/or seat belt buckle ends. If an incorrect part is used, the belt may not latch properly, increasing the risk of injury to the occupant should a vehicle crash occur. Correction: Vehicles will be inspected and incorrect parts replaced.
These vehicles were assembled with one or more incorrect safety belt and/or safety belt buckle ends. This does not conform with the requirements of fmvss no. 209, "seat belt assemblies."
Vehicle description: Passenger vehicles manufactured from august 1991 through july 1995. The transmission oil cooler line can separate when the vehicle is operated in low temperatures in combination with high transmission loads.
出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)、国土交通省(日本、公共データ利用規約1.0)、韓国国土交通部(car.go.kr)。