Fuel system, gasoline:Storage:Tank assembly
A fuel tank leak could occur due to small creases on the tank underside cracking during pressure cycling which occurs during normal operation.
🔔 無料アカウントを作成して Buick スカイホーク (すべての世代) のメール通知を受け取る
A fuel tank leak could occur due to small creases on the tank underside cracking during pressure cycling which occurs during normal operation.
燃料供給ホースおよび/またはリターンホース/パイプのアッセンブリに亀裂が入ったり、分離したりする可能性があり、その結果、燃料がボンネット内のエリアに漏れる恐れがあります。
On vehicles with 2.0l engines, the fuel feed and return hose assemblies may have been manufactured with improperly crimped fittings.A hose assembly with this condition may crack or separate from the fittng, allowing fuel to leak in the underhood area. This could result in an underhood fire. Correction:Hose assemblies will be replaced.
The engine air cleaner plastic trim cover could fall off the air cleaner assembly and land on the exhaust manifold creating a fire hazard. Consequence of defect: If the car is being operated at the time that the plastic trim cover falls off, an engine compartment fire could occur without warning.
The brake proportioner valves may break and separate from the master cylinder during braking. This will result in a loss of brake fluid and a partial loss of braking action
Possible fuel leakage could occur at the throttle body injection fuel feed pipe connection on the involved vehicles.
Under certaain conditions, the hose clamps on the fuel tank filler pipe and fuel tank filler vent pipe could fracture. The fracture of these clamps could cause fuel leakage at any of the four pipe to hose connections. Leakage can occur during refueling, or while driving, if the fuel tank is above 3/4 full.
Under certain conditions the hose clamps on the fuel filler pipe and fuel tank filler vent pipe could fracture. This could cause seepage of fuel at any one of the four pipe to hose connections when the fuel tank is above 3/4 full creating the possibility of fire.
内部腐食によりパルスエアのチェックバルブアセンブリが損傷すると、排気ガスがプラスチック製の遮断バルブを溶かし、バルブの破片が吸気清浄機およびスロットルボディに引き込まれるおそれがあります。
(手動調整式の運転席を備えた車両では、金属製のフロアパン・アンカーバーが、左前側の外側シートアジャスター・スタッドの周辺で疲労し破損するおそれがあります。その結果、スタッドがアンカーバーから外れ、運転席が予告なく後方へ傾く可能性があり、運転操作の喪失や車両の衝突につながるおそれがあります。 是正措置:フロアパン・アンカーバーに補強ブラケットを取り付けます。)
The metal floor pan anchor bar could fatigue and break around the left front outer seat adjuster stud of the drivers seat, allowing the stud to separate from the floor pan anchor bar.
Parking brake lever mechanisms may not properly engage when applied as required by fmvss 105. Consequence of defect: Vehicle could unexpectedly roll away uncontrolled, which could result in a vehicle crash.
These vehicles do not comply with c.M.V.S.S.108 - lighting equipment. Buick skyhawk custom 2 and 4 door sedans and limited 4 door sedans.
Incorrect tail lamp lens were installed, lens do not conform to fmvss 108, lamp reflective device and associated equipment. Consequence of defect: In times of reduced visibility, an approaching vehicle may not be aware of this vehicle which could result in a vehicle crash without prior warning.
On certain vehicles, the front seat back locks may not lock under forward load conditions and are therefore not in compliance with CMVSS 207 - Seat Anchorages.
Some vehicles have bucket seat back locks that do not conform to federal motor vehicle safety standard 207, anchorage of seats. In event of a crash, the seat back lock may not function.
The brake proportioner valves may break and separate from the master cylinder. This would allow brake fluid to leak and would result in a partial loss of the brake system.
出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)、国土交通省(日本、公共データ利用規約1.0)、韓国国土交通部(car.go.kr)。