配線
ステアリング・コラムに装着しているクロック・スプリング(運転席エアバッグ、ホーン、オート・スピード・コントロール機能を作動させるためのリボン状電気配線)の組み付けに不適切なものがあるため、ステアリングの操作によりクロック・スプリングの配線に損傷が生じて断線することがある。そのため、最悪の場合、ホーン・スイッチを操作してもホーンが鳴らない、また、エアバッグ警告灯が点灯し、運転席エアバッグが作動する条件下で衝撃を受けても、運転席エアバッグが展開しないおそれがある。
🔔 無料アカウントを作成して Chrysler タウン&カントリー III のメール通知を受け取る
このファイルには、Chrysler タウン&カントリー IIIで知られている不具合を、コミュニティが出典付きでまとめています。閲覧は無料、投稿には無料アカウントが必要です。信頼できる投稿者が十分に確認した不具合にはシールが付きます。
ステアリング・コラムに装着しているクロック・スプリング(運転席エアバッグ、ホーン、オート・スピード・コントロール機能を作動させるためのリボン状電気配線)の組み付けに不適切なものがあるため、ステアリングの操作によりクロック・スプリングの配線に損傷が生じて断線することがある。そのため、最悪の場合、ホーン・スイッチを操作してもホーンが鳴らない、また、エアバッグ警告灯が点灯し、運転席エアバッグが作動する条件下で衝撃を受けても、運転席エアバッグが展開しないおそれがある。
On certain minivans, the driver's air bag may become disabled due to a failure of the clockspring, which is located in the hub of the steering wheel.
On certain mini vans, the clockspring assembly may have been wound incorrectly during the vehicle assembly process.
Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary. When testing batteries and charging systems, the correct battery tester and charger must be used. Dealers must follow service information for the proper procedures when testing the charging system and batteries. Also, the dealer must follow warranty policies and procedures for proper reimbursement for battery replacement. Refer to the appropriate regional warranty manual to obtain specific warranty reimbursement requirements. This may include specific data which must be recorded and/or specific documentation which may be required to be attached to the work order. In the event the warranty policies and procedures are not followed, warranty reimbursement could be declined or charged back.
Radiator If vehicle comes in for transmission fluid leaking from trans-oil cooler fittings on the radiator, please check the following before replacing the radiator/cooler:~ 1. Remove both of the transmission lines from the cooler?s top/bottom flared fittings on the radiator. ~ 2. Loosen the hex nut on the top flared fitting on the radiator tank.~ 3. Torque the top flared fitting to 235 +/- 15 Lb-In.~ 4. Torque hex nut to 100 +/- 10 Lb-In.~ 5. Repeat for bottom flared fitting.~ 6. Reinstall transmission line per normal installation procedures and ensure correct fluid level.~ ~ If vehicle is in need of a new radiator for another reason, check the new radiator for correct torque on the trans-oil cooler fitting per steps 2-5 above.~ ~ If radiator has a yellow mark by the trans-oil cooler fittings the torque does not have to be checked.
Customer satisfaction notification regarding fuel pump module. *tt
出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)、国土交通省(日本、公共データ利用規約1.0)、韓国国土交通部(car.go.kr)。