On certain passenger vehicles, the camshaft position sensor may melt resulting in a burning smell and visible smoke, which may subsequently lead to the melting of the camshaft cover and the camshaft position sensor wire harness.
On certain passenger vehicles, the camshaft position sensor may melt resulting in a burning smell and visible smoke, which may subsequently lead to the melting of the camshaft cover and the camshaft position sensor wire harness.
Certain passenger vehicles fail to conform to the requirements of CMVSS no. 201, "occupant protection in interior impact." In the event of a crash in which the air bags do not deploy, there is a possibility of increased head injury to the front seat passenger should contact with the passenger side air bag cover occur. Correction: Dealers will install new energy absorbing air bag mounting brackets.
Vehicle description: Passenger vehicles equipped with alloy wheels and sold in puerto rico. These wheels were manufactured without the steel bushing inserts around the wheel bolt openings, allowing friction between the wheel bolt seats and the wheel bolts. This can result in the bolts loosening during hard braking.
Vehicle description: Passenger vehicles equipped with alloy wheels. These wheels were manufactured without the steel bushing inserts around the wheel bolt openings, allowing friction between the wheel bolt seats and the wheel bolts. This can result in the bolts loosening during hard braking.
The Camshaft position sensor may overheat causing the engine management warning light to illuminate and in the worst case a localised thermal incident may occur
Certain passenger vehicles fail to conform to the requirements of federal motor vehicle safety standard no. 201, "occupant protection in interior impact."
Certain passenger vehicles fail to conform to the requirements of federal motor vehicle safety standard no. 201, "occupant protection in interior impact."
On certain vehicles, the ECM wiring harness which is located in the passenger footwell area may chafe against a caulked body seam due to movement of the passenger's feet and result in a short circuit to ground. There is a possibility that engine driveablity may be affected and/or the engine may stall. Correction: Extra protection will be applied to the wiring harness and an additional tie strap will be installed to reroute the ECM harness away from the body seam.
Vehicle description: Passenger vehicles. A wiring harness, located beneath the carpet in the front passenger floor area, can become damaged by passenger traffic as the wire harness is rubbed against a body seam in the floor panel.
Vehicle description: Passenger vehicles. A wiring harness, located beneath the carpet in the front passenger floor area, can become damaged by passenger traffic as the wire harness is rubbed against a body seam in the floor panel.
On certain vehicles, insufficient wheel bolt torque could result in wheel separation and a possible crash without prior warning. Correction: Wheel bolt torque will be increased to 120nm (88lb/ft).
Vehicle description: Passenger vehicles. These vehicles do not comply with the requirements of fmvss no. 214, "side door strength." incorrect position of the side impact pad to the rear, instead of the middle, of the door assembly.
On certain vehicles, a pad located on the left hand and right hand door side impact beam was incorrectly positioned during vehicle manufacturing. The positioning of this pad is integral to the vehicle complying with the requirements of CMVSS 214 - Side Door Strength. Correction: All vehicles have had both left and right door pads re-positioned and secured in their intended position.
Vehicle description: Passenger vehicles. These vehicles do not comply with the requirements of fmvss no. 214, "side door strength." incorrect position of the side impact pad to the rear, instead of the middle, of the door assembly.
Vehicle description: Passenger vehicles. These vehicles do not comply with the requirements of fmvss no. 214, "side door strength." incorrect position of the side impact pad to the rear, instead of the middle, of the door assembly.
Vehicle description: 3 and 4-door passenger sedans. The steering wheel center bushing connecting the steering wheel hub to the steering column can slip.
出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)、国土交通省(日本、公共データ利用規約1.0)、韓国国土交通部(car.go.kr)。