On certain van and wagon vehicles equipped with 4-wheel antilock brake systems (abs), aftermarket batteries may leak electrolyte onto the abs control module connector, which can compromise sealing integrity of the connector.
Vehicle description: Vans and wagons not equipped with power front seats. In the presence of road salt, water, and possibly other debris, the power seat connector located beneath the driver's seat could develop a high resistive short circuit that cycles the circuit breaker.
Vehicle description: Pickup trucks. Sound deadener material inside the steering wheel could become detached from the cover and housing. Note: The ram pickup trucks were built at the warren assembly plant ("s" in the 11th vin position) from may 16, 2000 through october 23, 2000; st. Louis north assembly plant ("j" in the 11th vin position) from may 19, 2000 through october 23, 2000; lago alberto assembly plant ("m" in the 11th vin position) from may 23, 2000 through october 23, 2000; and saltillo assembly plant ("g" in the 11th vin position) from may 23, 2000 through october 23, 2000. Important: Vehicles that have already had the proper clockspring installed, according to warranty records, have been excluded from this recall. In addition, 1997-2000 model year vehicles that have had a suspect replacement clockspring installed, according to warranty records, have been added to this recall.
Vehicle description: Certain van, wagon, pickup trucks, passenger and sport utility vehicles, fail to comply with requirements of fmvss no. 209, "seat belt assemblies." the front seat belt retractor may not comply with the requirements of the standard.
Vehicle description: Pickup trucks equipped with gasoline engines and manual transmissions. The underbody hydraulic clutch line heat shield is too short, allowing the plastic clutch line material to be directly exposed to exhaust temperatures. It is possible to exceed the melting temperature of the clutch line material.
Vehicle description: Pickup trucks equipped with manual transmission, v10 engines and four-wheel-drive transfer cases. Under sustained maximum rated vehicle load, while driving up a steep grade in four-wheel-drive low range in hot ambient conditions, the local exhaust temperature proximate to the hydraulic clutch line can generate line temperatures that exceed the temperature limit of the clutch line material. If this condition occurs and the clutch is depressed, the line could rupture.
Vehicle description: Passenger vans and wagons equipped with compressed natural gas (cng). The fuel hose that connects the left and right fuel rails may shrink and leak fuel if exposed to high engine operating temperatures.
Vehicle description: Vans equipped with compressed natural gas (cng) fuel tanks. Incorrect fuel tank straps were installed on the small fuel tank. As a result, the fuel tank may not be securely attached to the vehicle.
On certain vehicles, the low pressure diesel fuel supply tube located in the engine compartment between the filter and the high pressure pump may fracture and leak, possibly resulting in an engine compartment fire. Correction: The steel low pressure diesel fuel supply tube will be replaced with a rubber isolated tube.
Vehicle description: Light duty pickup trucks equipped with 5.9l - 24 valve diesel engine. The low pressure diesel fuel supply tube located in the engine compartment between the filter and the high pressure pump can fracture.
On certain vehicles, an exhaust system heat shield attaching screw is too close to the underbody fuel line. Vibration and vehicle motion during normal vehicle operation may cause the fuel line to rub against the screw eventually resulting in fuel leakage. Correction: Heat shield attaching screw will be removed and replaced with a butyl rubber adhesive. Fuel tubes showing any signs of abrasion damage will be replaced.
Vehicle description: Light duty trucks equipped with either a 8.0l v-10 engine or a 5.9l v-8 heavy duty gasoline engine. An exhaust system heat shield attaching screw is too close to the underbody fuel line. The line can rub against the screw, possibly causing fuel leakage.
On certain vehicles, the fuel tank mounted rollover valve may allow liquid fuel to leak onto the ground under certain conditions. In the presence of an ignition source, a fire could occur. Correction: The fuel tank rollover valve will be replaced with a float type rollover valve.
Vehicle description: Light duty pickup trucks equipped with gasoline engines. The fuel tank mounted rollover valve can allow liquid fuel to leak onto the ground under certain vehicle operating conditions.
Vehicle description: Light duty trucks equipped with diesel engines. The exhaust pipe contacts or is in close proximity to the outer dash panel silencer pad.
On certain vehicles, the exhaust pipe may be in contact or close proximity to the outer dash panel silencer pad. It is possible that the pipe can generate sufficient heat to cause the pad material to smolder and may ignite adjacent materials resulting in a vehicle fire. Correction: The outer dash silencer pad adjacent to the exhaust pipe will be removed and replaced by a thermal heat shield on the exhaust pipe.
Under certain high load operating conditions, the transmission fluid temperature can exceed the melting point of the material used in the connector to retain the fluid line to the transmission.
On certain vehicles, the plastic pins and metal clip that retain the steering column lower shaft could break, causing the lower shaft to separate from the upper shaft. This would result in loss of steering control and a possible crash without prior warning. Correction: A restraining sleeve will be added to the intermediate shaft to limit the amount of axial steering column shaft movement possible in the event the plastic pins and metal clip are broken.
If the plastic pins and metal clip that retain the lower steering shaft in the upper shaft break, the lower steering shaft can separate from the upper shaft.
The fasteners which secure the generator cartridge fuse to the power distribution center may have an improper clamp load. Improper clamping can result in arcing at the connection.
On certain vehicles, the extra keys operator's key ring may become temporarily lodged in the airbag screw access holes on the steering wheel back cover, hampering steering wheel return. In some cases, the force used to return the wheel may also cause the vehicle ignition to be turned off. Correction: Plugs will be installed in the steering wheel back cover airbag screw access holes to prevent the potential for any key interference. *note: Chryler recall #642 supercedes this recall campaign, t.c. 95-108.
These vehicles do not comply with c.M.V.S.S. 301 - fuel system integrity. A routine rear impact compliance test resulted in fuel leakage during rollover stage in excess of that allowed by the standard. Correction: A rail reinforcement bracket will be installed to the undercarriage to prevent damage to the fuel tank filler nipple and hose.
出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)、国土交通省(日本、公共データ利用規約1.0)、韓国国土交通部(car.go.kr)。