電気系統
一部の1996~1998年型のパッセンジャー車(カンザスシティ工場、クアウティトラン工場製)、および一部の1999年型のパッセンジャー車(オートモーティブ・アライアンス・インターナショナル工場製)では、ヒーターブロワー抵抗器のステンレス鋼製ブレードの粗い表面が、ワイヤーハーネスコネクターの銅製表面を傷つけることがあります。この損傷が長期間にわたって進むと、コネクター内の抵抗が増加し、その後の端子の応力緩和によって回路が断線(オープン回路)に至る可能性があります。
🔔 無料アカウントを作成して Ford コントゥア (すべての世代) のメール通知を受け取る
一部の1996~1998年型のパッセンジャー車(カンザスシティ工場、クアウティトラン工場製)、および一部の1999年型のパッセンジャー車(オートモーティブ・アライアンス・インターナショナル工場製)では、ヒーターブロワー抵抗器のステンレス鋼製ブレードの粗い表面が、ワイヤーハーネスコネクターの銅製表面を傷つけることがあります。この損傷が長期間にわたって進むと、コネクター内の抵抗が増加し、その後の端子の応力緩和によって回路が断線(オープン回路)に至る可能性があります。
Vehicle description: Bi-fuel vehicles. These vehicles may have a fuel tank filler pipe grommet that could have been damaged during the installation of the bi-fuel system. If the grommet is damaged, fuel could leak. Fuel leakage in the presence of an ignition source could result in a fire. Dealers will replace the fuel tank filler pipe grommet.
On certain vehicles, the fuel filler pipe vent hose may have less than the intended level of ozone resistance, which could result in the hose becoming brittle and cracking. A cracked hose could result in fuel leakage when the vehicle is being fueled. Fuel leakage in sufficient quantity in the presence of an ignition source could potentially result in a fire. Correction: Dealers will install a fuel filler vent hose containing the appropriate blend of PVC and nitrile rubber.
Vehicle description: Passenger vehicles. The fuel filler pipe vent hose may have less than the intended level of ozone resistance, which could result in the hose becoming brittle and cracking.
Vehicle description: Bi-fuel vehicles modified to run on either gasoline or compressed natural gas (cng). The natural gas fuel tanks have a solenoid shut-off valve that stops fuel flow from the fuel tank in the event of certain moderate to severe collisions. If the vehicle is in a collision and the natural gas fuel line is damaged, the system could leak natural gas.
The fuel tank filler pipe opening reinforcement, fabricated from two separately moulded pieces spin welded together, may eventually leak fuel at the weld joint. Fuel leakage in the presence of an ignition source, could potentially result in a fire. Correction: Fuel tank assemblies will be replaced with ones containing one piece moulded reinforcements.
The fuel tank filler pipe opening reinforcement, constructed from two separately molded pieces, can leak at the weld.
The passenger side supplemental restraint system (air bag) may have a cracked inflator body. If the vehicle is involved in a deployment level crash, the passenger side air bag may not inflate properly which could result in reduced occupant protection. In addition, the igniter plug could separate from the inflator, which could result in the release of hot gases and could ignite flammable material or potentially cause personal injury. Correction: Vehicles will be inspected and a new passenger side air bag module will be installed if necessary.
The fuel tank filler pipe opening reinforcement can leak at the weld.
The fuel filler opening reinforcement (an integral part of the fuel tank assembly) may leak fuel. In the presence of an ignition source, a fire could result. Correction: Fuel tank will be replaced on affected vehicles.
A metal shield on the outside of the plastic fuel filler pipe can develop a static electrical charge during refueling of the vehicle.
Vehicle description: Passenger vehicles built at the kansas city assembly plant and originally sold in or currently registered in the states of connecticut, delaware, illinois, indiana, iowa, maine, maryland, massachusetts, michigan, minnesota, missouri, new hampshire, new jersey, new york, ohio, pennsylvania, rhode island, vermont, west virginia, and wisconsin, and the district of columbia. The front coil springs may fracture as a result of corrosion in high corrosion environments. Depending on the location of the fracture, a broken spring could move past the spring seat and contact a front tire.
Vehicle description: Passenger vehicles built with an incorrect power brake booster and master cylinder assembly.
車両概要:2.0Lおよび2.5Lエンジンを搭載した1995年式乗用車、ならびに2.5Lエンジンを搭載した1996年式車両。 エンジン冷却ファンモーターのベアリングが固着し、モーターのストール(停止)に至るまで進行すると、モーターのトルクが増加し、通常より高いモーター電流と、それに伴うモーター温度の上昇を招くおそれがあります。
**車両の説明:** trw製シートベルトバックル組立品を装着した乗用車、小型トラック、スポーツ用多目的車(SUV)、およびミニバン。これらのシートベルト組立品のバックルベースは適切に熱処理されておらず、そのため連邦自動車安全基準第209号「シートベルト組立品」の荷重支持要件に適合しません。
車両の説明: アンチロックブレーキシステム(abs)non装備の乗用車。路面の融雪や防塵に塩化物系化合物を使用している地域で運転すると、後輪ブレーキの圧力感知式減圧弁(pcrv)が腐食し、作動不良を起こす場合があります。
Vehicle description: Passenger vehicles. The air bag sensor wiring pigtail insulation can become brittle and crack over time due to accumulation of water in the pigtail protective convolute in combination with high underhood temperatures related to the routing of the wiring pigtail near the radiator. This can result in environmental stress cracking of the insulation.
Vehicle description: Passenger vehicles. The accelerator cable may have been manufactured with a burr on or near the end of the cable sleeve interior. This burr could fray the core wire resulting in the accelerator not returning to idle when the accelerator is released.
Vehicle description: Passenger vehicles. The terminals at the headlight switch and wiring harness connector can experience heat damage as a result of overheating.
Vehicle description: Passenger vehicles built with automatic transmissions which utilize a park/lock solenoid. It is possible to rotate the ignition key to the lock position and remove the key without the shift lever and transmission being in park. These vehicles do not comply with the requirements of fmvss no. 114, "theft protection."
Certain vehicles do not comply with CMVSS 205 - glazing materials. The windshields on were produced without the "AS1" mark as required by American National Standards Institute (ANSI) Z26.1. These windshields fully meet all of the requirements of Standard 205. Correction: Since the absence of the AS1 mark is highly unlikely to produce any risk of injury, no corrective action will be taken.
Certain vehicles may not comply with CMVSS 1105 - evaporative emissions. The rear fuel lines may allow fuel to seep and evaporate at the metal line to nylon tube joint at the rear of the vehicle near the fuel filter. This may cause evaporative emissions in excess of the standard. Correction: Vehicle will be inspected for signs of fuel escaping a joint between a nylon tube and a metal fuel line. If wetness or fuel odor are detected a reinforcement kit will be installed.
On certain vehicles, the floor shift automatic transmission control may be damaged if subjected to certain vehicle interior cleaning products. If exposed to these products, the transmission gear position indicator may deteriorate and not correctly indicate the actual gear position. If this occurs, the shifter will continue to operate normally, but there is the potential for incorrect gear selection. Correction: Automatic transmission floor shift control will be replaced.
Vehicle description: Passenger vehicles. The floor shift automatic transmission control can be damaged if subjected to certain interior cleaning products. The gear position indicator can deteriorate and not correctly indicate the actual gear position.
Note: Vehicles equipped with 2.5 litre engines. These vehicles may not comply with c.M.V.S.S. 1103 - exhaust emissions. Premature failure of the catalyst substrate material in the catalyst and exhaust manifold assemblies (light-off catalysts) can result in restricted exhaust gas flow, loss of power and exhaust emission levels in excess of those specified in the standard. Correction: Left and right hand light-off catalysts will be replaced. Underbody catalyst will be inspected and replaced if necessary.
出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)、国土交通省(日本、公共データ利用規約1.0)、韓国国土交通部(car.go.kr)。