視界:デフロスター/デフォッガー/HVACシステム:ヒーターコア
ヒーターコントロールバルブのステムは材料仕様を満たしていません。冷却水温度が高くなると、ステムから漏れが生じる可能性があります。
🔔 無料アカウントを作成して Hyundai エクセル (すべての世代) のメール通知を受け取る
ヒーターコントロールバルブのステムは材料仕様を満たしていません。冷却水温度が高くなると、ステムから漏れが生じる可能性があります。
The車両はFMVSS 301「燃料system integrity(燃料システムの完全性)」の側面移動バリア衝突試験の要件に適合しませんでした。燃料タンクからの燃料漏れが、許容される最大漏出量を超えていました。 Let me correct that: the translation should be fully in Japanese. 車両は、FMVSS 301「燃料システムの完全性」の側面移動バリア衝突試験の要件に適合しませんでした。燃料タンクからの燃料漏れが、許容される最大漏出量を超えていました。
Note: All 1988-89 excel vehicles sold in canada. The reed valve subassembly contained within the air control valve could fail due to corrosion allowing the hot exhaust gases to flow backward into the plastic secondary air filter case when the vehicle is being driven. These hot gases may melt the secondary air filter case and could result in an engine compartment fire. Correction: Reed valve subassembly will be replaced.
Vehicle may fail to conform to the brake fade and recovery portion of fmvss 105.
The fuel return tube clip may have been incorrectly installed allowing the fuel return hose to contact either the distributor high tension cable or the e.G.R. Valve. This could, over time, result in wear and eventual leakage at the fuel hose. The fuel leakage could result in an underhood fire. V.I.N. Range s.O.P. To kmhla31j1gu040086
In some vehicles, the manufacturer's protective internal coating of the electronic crank angle sensor does not meet specifications, which can cause an open circuit at high operating temperatures. This can cause the vehicle to stall.
マニュアルトランスミッションは、トランスミッションケース内のギアへの潤滑が不足すると、ロックアップすることがあります。これにより駆動輪が固着し、車両が突然停止する可能性があります。
Deterioration of the reed valve subassembly may lead to a malfunction within the secondary air supply portion of the emission control system. The screws which attach the reeds to the reed valve subassembly may rust, and if the rusting becomes severe, the screw heads will erode and allow the reeds to separate from the reed valve subassembly. Corrosion may also occur on the reed valve subassembly, deforming the reed seats and preventing the reeds from closing properly. Separation of the reeds from the reed valve subassembly or improper closing of the reeds allow hot exhaust gases to flow backward into the plastic secondary air filter case when the vehicle is being driven. These hot exhaust gases may melt the secondary plastic air filter case.
The lock washer located under the nut that secures the front hub to the driveshaft may crack due to improper heat treatment. This could result in wheel bearing freeplay and bearing damage with possible wheel lock-up or brake caliper knockback. Correction: Washer will be replaced note: All units have been corrected.
Lock washer located under the nut that secures the front hub to the drive shaft may have had improper heat treatment and could crack.
The possibility exists that under certain braking conditions, front brake fade may occur,thus reducing braking effectiveness. Correction: Improved semi-metallic brake pads will be installed.
The cotter pin that retains the brake clevis pin may have been omitted or incorrectly installed. If the cotter pin was omitted or if it were to fall out of the clevis pin,the vehicles' brakes would be subject to failure without warning.
A cotter pin in the brake pedal to brake master cylinder linkage assembly may be missing. This pin acts as a retainer for the brake master cylinder pushrod clevis pin. Consequence of defect: The clevis pin may slide out causing the master cylinder/brake pedal linkage to become disengaged. If this linkage becomes disengaged the service brakes cannot be applied, creating the risk of a crash without prior warning.
If cruise control main switch is in the on position when engine is started, system can be affected by a short duration voltage drop caused by optional hi-power (h340) radio.
出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)、国土交通省(日本、公共データ利用規約1.0)、韓国国土交通部(car.go.kr)。