Isuzu diesel engines available in the above affected vehicles meet the california air resource board's (carb) optional idling emissions standard of 30 grams per hour of oxides of nitrogen (nox) with no increase in the emission of other regulated pollutants. As a result these vehicles have been approved as "certified clean idle" and are "exempt" from the engine shutdown system (ess) requiremnet pursuant ot section 1956.8 of title 13, california code of regulations. As required by the ess regulation, for "certificed clean idle" vehicles, isuzu has introduced a tamper resistance "certified clean idle" label located on the driver's side door panel. It is important that this label remain, permanently, on the vehicle to identify it as "certified clean idle." carb requires this label as evidence that, at hte time of manufacture, the engine installed met the applicable emission standards. Should the label be found missing or damged during an inspection, a citation and penalties may be issued. If the vehicle is operated in california with a damaged or missing clean idle label, isuzu recommends vehicle operators follow the 5 minute ess requirement by manually turning off the engine. Following this ess requiremnet will keep the vehicle operation compliant until a replacement label can be installed. "clean air idle" labels are printed with a serial number and registered to an individual vin. As a result, a replacemnet label will also include a new serial number which must be registered to the vehicle's vin by the manufacturer. The below information is provided to assit in acquiring, replacing and registering a replacement label.
This Preliminary Information communication provides information to the technician with the axel setup information from American Axle Manufacturing. Technician should be advised that the maximum pinion shim to be used or stacked behind the pinion is 0.050?, and the minimum pinion shim is 0.020? for an 8.6 axle. The range for available pinion depth shims for the 10.5? axle is 0.006? to 0.024?. When setting the backlash it should be set between 0.003? to 0.005? on a new ring and pinion for any American Axle Manufacturing application. The ring and pinion can be reused or adjusted if the mileage is less than 500 miles, if not used for towing. Technician should be advised that a ?roller coaster? or ?hourglass? pattern on the bearings may be normal up to 10,000 miles and possibly longer. With a mis-machined housing you may get a heel pattern on both sides of the gear teeth at build up can generally be corrected with backlash adjustments. When setting up an 8.6? axle with a 5 cut gear set is to use a 0.035? pinion shim and set backlash to 0.004?. When using the newer 2 cut gear set also use a 0.035? pinion shim and still set backlash to 0.004?. To set the gear pattern use backlash to adjust the pattern heel to toe. Use the pinion shim to adjust the height of the pattern. The proper drive pinion bearing pre-load is from 15 - 30 inch pounds with new bearings. The total torque to turn after the differential case is installed should increase 5 - 10 inch pounds at the pinion. A new pinion nut must be used whenever the old one is removed. The axle shaft end play specification is 0.012? per side and the radial specification is 0.002? - 0.003?. Technician should be advised that synthetic lube can be used in all new American Axle Manufacturing axle assemblies. The new pinion seal for the 8.6? axle assembly is a two piece design.
Policies and procedures update for all commercial vehicles. This bulletin provides instructions with regard to the Isuzu Commercial Vehicle (CV) Warranty Parts Center on the topics of parts retention, parts preparation for shipping, and administration.
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that experience normal audio. This could be due to interference from transmitting sources outside of Sirius XM?s frequency range.
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that experience normal audio. This could be due to interference from transmitting sources outside of Sirius XM?s frequency range.
This informational bulletin provides Information Regarding Servicing Components Located Near SIR Components and how to properly disable the SIR system for repairs at or near
Service update for inventory and customer vehicles fuel sending unit port fracture-extended starts/sluggish acceleration/check engine light-expires with base warranty. *kb
出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)、国土交通省(日本、公共データ利用規約1.0)、韓国国土交通部(car.go.kr)。