DL: On December 20, 2022, a settlement of claims for certain low pressure fuel pumps was approved by the federal court. The settlement includes Lexus?s agreement to provide a Customer Support Program for certain 2013-2020 model year (MY) vehicles originally equipped with low pressure fuel pumps repaired under Safety Recall 20LA01 or Special Service Campaign 21LC01. The purpose of this Customer Support Program letter is to help clarify how to administer this coverage in accordance with the settlement.
TSB: Some 2013 ? 2020 model year Lexus vehicles may exhibit a hard start and/or MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs): ?DTC P0171 and/or P0174 (System Too Lean Bank 1/Bank 2) ?DTC P0087 Fuel Rail / System Pressure ? Too Low Techstream data list analysis may reveal positive fuel trims including a no pressure condition verified by a manual fuel pressure gauge. Follow the Repair Procedure in this bulletin to address these conditions.
This is to advise of various price adjustments affecting Genuine Lexus Motor Oil and Long-Life Coolant, effective March 1, 2023. These products are ordered through the Lexus Complete Maintenance Care (LCMC) website.
DP: The subject vehicles may have been equipped with an engine containing an incorrectly manufactured Crankcase Case Vent. If the engine is equipped with an incorrectly manufactured Crankcase Case Vent, the vehicle may release crankcase emissions.
TT: Some IS250 and GS300 vehicles may exhibit one or more of the following conditions: ? MIL ?ON? DTC P0300, P0301, P0302, P0303, P0304, P0305, and/or P0306. ? Intermittently runs rough after coming to a stop with the engine at operating temperature. ? Intermittently runs rough with engine misfires present after a cold soak startup. NOTE: The recommendations in this document apply to an intermittent misfire concern. If a vehicle exhibits a steady misfire, the root cause is not related to the referenced service bulletins and the repair manual should be referenced for diagnosis.
TT: TMS has discovered the current engine active test ?Control the Injection Mode? is not operating as desired when controlling the direct injectors manually on 2GR-FKS or 8AR-FTS engines. When direct injection is started and then stopped using the active test, current ECU logic does not turn off the direct injectors and can cause DTCs P017200, P017500 and P0160300. In order to avoid this condition, technicians should raise engine RPM when changing from Direct Injection active test to Port Injection active test. Use the recommended procedure below to avoid this concern while testing injection mode of 2GR-FKS or 8AR-FTS equipped vehicles. NOTE: If the active test is used multiple times without using this procedure to raise engine RPM, it may be necessary to reset learning values for fuel trim and Air to Fuel ratio before returning vehicle to customer.
Some IS250 and GS300 vehicles may exhibit one or more of the following conditions: MIL "ON" DTC P0300, P0301, P0302, P0303, P0304, P0305, and or P0306. Intermittently runs rough after coming to a stop with the engine at operating temperature. intermittently runs rough with engine misfires present after a cold soak startup.
Some IS250 and GS300 vehicles may exhibit one or more of the following conditions: MIL ?ON? DTC P0300, P0301, P0302, P0303, P0304, P0305, and/or P0306 Intermittently runs rough after coming to a stop with the engine at operating temperature Intermittently runs rough with engine misfires present after a cold soak startup
Tech Tip: Some IS250 and GS300 vehicles may exhibit one or more of the following conditions: MIL "ON" DTC P0300, P0301, P0302, P0303, P0304, P0305, and/or P0306. Intermittently runs rough after coming to a stop with the engine at operating temperature. Intermittently runs rough with engine misfires present after a cold soak startup. NOTE: The recommendations in this document apply to an intermittent misfire concern. If a vehicle exhibits a steady misfire, the root cause is not related to the referenced service bulletins and the repair manual should be referenced for diagnosis.
"tt: Tms has discovered the current engine active test control the injection mode is not operating as desired when controlling the direct injectors manually on 2gr-fks or 8ar-fts engines. When direct injection is started and then stopped using the active test, current ecu logic does not turn off the direct injectors and can cause dtcs p017200, p017500 and p0160300. In order to avoid this condition, technicians should raise engine rpm when changing from direct injection active test to port injection active test. Use the recommended procedure below to avoid this concern while testing injection mode of 2gr-fks or 8ar-fts equipped vehicles. Note: If the active test is used multiple times without using this procedure to raise engine rpm, it may be necessary to reset learning values for fuel trim and air to fuel ratio before returning vehicle to customer."
"tt: Some is250 and gs300 vehicles may exhibit one or more of the following conditions: Mil on dtc p0300, p0301, p0302, p0303, p0304, p0305, and/or p0306. Intermittently runs rough after coming to a stop with the engine at operating temperature. Intermittently runs rough with engine misfires present after a cold soak startup. Note: The recommendations in this document apply to an intermittent misfire concern. If a vehicle exhibits a steady misfire, the root cause is not related to the referenced service bulletins and the repair manual should be referenced for diagnosis."
Lexus: Some vehicles may exhibit a mil on condition with one or more of the following diagnostic trouble codes (dtcs): P0300, p0301, p0302, p0303, p0304, p0305, and p0306-random misfire detected; cylinder 1-6 misfire detected. This condition is not not dependent on engine temperature or initial engine run time. *pe
出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)、国土交通省(日本、公共データ利用規約1.0)、韓国国土交通部(car.go.kr)。