Insufficient pressing of parts in the high pressure fuel pump can cause movement of the cylinder in the fuel pump through which the piston moves. This can create wear between the cylinder and the pump body, resulting in increased stress on valves and/or movement valve seat inside the pump body. This increased stress can cause a crack in the weld of the affected valves, which could lead to a fuel leak, increasing the risk of fire.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2025 Toyota Camry Hybrid, Lexus NX250, NX350, NX350 Hybrid, 2024-2025 Lexus RX350, RX350 Hybrid, and RX500 Hybrid vehicles. The second-row center seat belt webbing may be damaged. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 209, "Seat Belt Assemblies."
Issue: On a small number of vehicles, the bolts that secure the front brake caliper mounting bracket(s) and the wheel hub(s) to the steering knuckle(s) may not have been tightened properly. As a result, the caliper(s) could move and cause the brake hose(s) to become damaged. If this happens, brake fluid could leak and cause reduced braking. Additionally, the hub bolts could loosen and cause the front wheel(s) to separate from the vehicle. Safety Risks: Reduced braking can cause extended stopping distances and increase the risk of a crash. A wheel separation could cause a loss of control and increase the risk of a crash. A wheel that separates could also create a hazard for others. Corrective Actions: The company will notify owners in writing and advise you to take your vehicle to a dealership to inspect and, if necessary, tighten the front brake caliper bracket and wheel hub bolts. The dealer will replace any damaged components, as necessary.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2024 RAV4 and 2025 Lexus NX vehicles. Some of the bolts that secure the front brake caliper and the wheel hub bearing may be loose, which can result in a damaged caliper brake hose or possible wheel detachment.
Certaines soudures ont été manquées lors du soudage des panneaux de carrosserie aux amortisseurs avant gauche et droit. en conséquence, des fissures et des bris peuvent se produire sur d’autres soudages et/ou sur les panneaux de carrosserie autour des zones de montage de l’amortisseur avant. cela pourrait entraîner une séparation d’un amortisseur avant de la zone de montage, entraînant une perte de stabilité de conduite du véhicule, augmentant ainsi le risque d’accident.
Insufficient press-in mounting of certain components of the high-pressure fuel pump could lead to increased pressure on the valves within the pump. This may cause the weld seams of the affected valve(s) to crack, which could lead to a fuel leak. In the presence of a source of ignition, a fuel leak could lead to an increased risk of fire.
The DC-DC converter may be faulty, which can cause the current from the 12V battery to continue to flow, generating heat and increasing the risk of a vehicle fire.
The plug-in hybrid system of the subject vehicles includes a DC-DC converter that reduces the voltage of the electricity from the Hybrid Vehicle (HV) battery in order to charge the vehicle�s 12V battery. Contained within the DC-DC converter is a current rectifying module that is installed on the circuit board. Some of these modules may have been damaged during production by the supplier and could fail so creating a short circuit. This allows current from the 12V battery to continue to flow through the module and the module will generate heat. Under certain conditions if excessive heat is generated components within and outside the DC-DC converter could sustain thermal damage increasing the risk of a vehicle fire.
DC-DC 컨버터(전압 변환장치)의 내부 회로 설계 오류로 내부 부품이 손상되고 이로 인해 단락이 발생할 수 있으며, 이런 경우 경고등이 점등되고 12V 배터리에서 전류가 계속 흐르게 되어 과도한 열이 발생되므로 최악의 경우에는 화재에 이를 우려가 있음이 확인됨에 따른 리콜
Issue: On certain plug-in hybrid vehicles, the DC-DC converter located under the rear seat could fail. If this happens, the DC-DC converter and nearby parts could overheat. Safety Risk: A DC-DC converter that overheats can create the risk of a fire. Corrective Actions: Toyota will notify owners by mail and advise you to take your vehicle to a dealership to replace the DC-DC converter. To reduce the safety risk, Toyota recommends not to charge your vehicle while the air temperature is below or expected to drop below 5° C until the recall repairs have been completed.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2021-2022 RAV4 Prime and 2022 Lexus NX450h+ plug-in hybrid electric (PHEV) vehicles. The electric current rectifying module contained within the DC-DC converter may have been damaged during production, which can result in an electrical short-circuit.
There could be a fault with the pressure sensors for the airbag system. This could lead to the non-deployment of the side/curtain shield airbags and/or front airbags, increasing the risk of injury to the occupants in the event of a crash.
On certain vehicles, the airbag system pressure sensors and/or acceleration sensors used to detect vehicle impact may contain manufacturing defects. As a result, the airbag warning light may illuminate and the side/curtain shield airbags and/or front airbags may not deploy, increasing the risk of injury in the event of a crash. Correction: Dealers will inspect and replace the defective sensors as necessary. Note: This will not affect the front airbags of the Prius model.
On certain vehicles, the electrical power cords of some dealer installed block heaters may have been improperly manufactured, causing the wires to contact each other, resulting in a short circuit. A short circuit could lead to a fire which would increase the risk of injury and/or damage to property. Correction: For vehicles where the subject block heater was approved for installation, the dealer will replace the block heater assembly with a new one of an improved design. For vehicles where the subject block heater was not approved for installation, dealers will remove the block heater assembly. In the interim, until the remedy can be performed, dealers will cut the plug end from the block heater cord to disable the block heater's operation.
La programmation du logiciel de la caméra de reconnaissance avancée peut entraîner une défaillance de la mémoire lorsque l'allumage est éteint, ce qui peut empêcher le système de précollision de s'activer lors du prochain démarrage, de déclencher des voyants d'avertissement, de sonner des carillons et d'afficher des alertes sur le tableau de bord. ignorer ces avertissements peut augmenter le risque d'accidents et de blessures.
Issue: On certain vehicles, the brackets that secure the driver and front passenger seats may not have been welded properly. As a result, the seat(s) could move in a crash. Safety Risk: A seat that moves in a crash could increase the risk of injury. Corrective Actions: The company will notify owners by mail and advise you to take your vehicle to a dealership to inspect and, if necessary, repair the welds.
Issue: Under certain conditions, a software problem could cause the rearview camera image not to display when the transmission is shifted into reverse. Safety Risk: A rearview camera image that doesn't display could reduce a driver's ability to see behind the vehicle while backing up. This could increase the risk of a crash. Corrective Actions: Lexus will notify owners by mail and advise you to take your vehicle to a dealership to update the rearview camera software or replace the rearview camera, as necessary.
出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)、国土交通省(日本、公共データ利用規約1.0)、韓国国土交通部(car.go.kr)。