閲覧無料 · 投稿は無料アカウントでAnticars(2000年)の後継

Mazda Mazda3

2003– · 4 世代 · 不具合63件 · 8市場
世代

技術サービス通報(TSB)は、既知の不具合についてメーカーが販売店に送る修理指示です。安全リコールではありませんが、不具合の裏付けになることがよくあります。

年式
Mazda3 IV · 2019–
技術通報中程度電装NA

技術通報

Some customers may experience the check engine light on with DTC P0126:00 (Thermostat stuck open) stored. This is due to improper PCM logic control. To eliminate the concern, the PCM control software has been modified. REPAIR PROCEDURE 1. Verify the customer concern. 2. Reprogram the ECU with the Mazda Modular Diagnostic System (M-MDS), using Mazda Diagnostic and Repair Software (MDARS). Refer to MDARS ECU Reprogramming Procedure. NOTE: Be sure to submit Diagnostic Information (ODR) data as it is a required item and will be checked during warranty claim submission. Instructions can be found under M-MDS -> MDARS (Uploading Diagnostic Information (ODR) Data). 3. Clear any other DTCs. 4. Verify the repair by starting the engine (READY ON) and confirming there is no CHECK ENGINE light ON or abnormal warning lights present.

NHTSA · メーカー通報11030600モデルイヤー 2026原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda3 IV · 2019–
技術通報中程度ブレーキNA

技術通報

Some customers may experience the following concerns: The liftgate or the trunk lid will not unlock even when the vehicle is parked and the ignition is off. If the engine is running (POWER ON) or the ignition is turned to on (READY ON), it will unlock. The auto close operation of the power liftgate is not performed (The liftgate can be closed manually). To eliminate this concern, the control software of the DSC HU/CM (or the electronically controlled brake unit) has been modified. Customers

NHTSA · メーカー通報11003356モデルイヤー 2024原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda3 IV · 2019–
技術通報中程度エンジンNA

技術通報

Please be advised that the valve stem seals assigned to the 2.5 Skyactiv Turbo engines in GEPC are incorrect. The Diesel Valve Stem seal SH09-10-1F5A, which is for Diesel engines, is currently listed for these models in GEPC. Please ensure that the proper valve stem seals are used for the 2.5 Skyactiv Turbo engines affected by SSPD5 have the correct valve seal part number PY8W-10-1F5 installed on PYT engines to avoid any potential issues.

NHTSA · メーカー通報11000679モデルイヤー 2021原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda3 IV · 2019–
技術通報中程度ブレーキNA

技術通報

Some customers may experience that the liftgate or the trunk lid will not unlock even when the vehicle is parked and the ignition is off. If the engine is running (POWER ON) or the ignition is turned to on (READY ON), it will unlock. To eliminate this concern, the control software of the DSC HU/CM (or the electronically controlled brake unit) has been modified.

NHTSA · メーカー通報10254184モデルイヤー 2024原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda3 IV · 2019–
技術通報中程度トランスミッションNA

技術通報

The A/T (Automatic Transmission) warning light is flashing in the instrument cluster at new car delivery, without any DTCs being present.

NHTSA · メーカー通報10246213モデルイヤー 2024原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda3 IV · 2019–
技術通報中程度サスペンションNA

技術通報

Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 7000C0A-NA04_12004 or later). Ver. 7000C0A-NA04_12004 and later fixes these software errors (bugs): * Album artwork may not appear when playing music using an USB connected iPhone. * When the gear position is shifted into P from R, the screen may not return to the previous condition before shifting into R position. * The screen freezes and goes to a white screen, then the system reboots. * The steering wheel switches and commander switches cannot control the audio system. * DTC U3000:49 is stored which may be accompanied with following symptoms: - No sound emitting from the speakers. - Audio source selection is unavailable. * The vehicle icon rotates when using the navigation with head-up mode. * Beep sounds every after couple of minutes. * Language setting may not be accepted correctly. * The audio track may not pause when pressing the mute button. * The system reboots. * The screen may turn black when trying to play a video file in the USB connected device.

NHTSA · メーカー通報10226900モデルイヤー 2021原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda3 III · 2013–2018
技術通報中程度ボディNA

技術通報

断続的なクランキング不良/始動不能 一部のお客様から、断続的にクランキングしない、またはエンジンが始動しないという症状が報告される場合があります。これは、インストゥルメントパネル配線ハーネスのコネクターC12の接続不良が原因である可能性があります。運転席側Aピラーにあるコンパス付きアクセサリーミラーのTハーネスコネクターが、正しく装着(ロック)されていない可能性があります。 お客様の症状を解決するには、インストゥルメントパネル配線ハーネスの上側および下側のC12コネクターを、しっかりと確実に接続してください。

NHTSA · メーカー通報10213452モデルイヤー 2016自動翻訳 · 原文:英語詳細を見る →
Mazda3 III · 2013–2018
技術通報中程度ブレーキNA

技術通報

MultiModel (A/T ONLY) ACCESSORY ALUMINUM ALLOY BRAKE PEDAL APPLICATION

NHTSA · メーカー通報10213463モデルイヤー 2015原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda3 IV · 2019–
技術通報中程度ボディNA

技術通報

Some vehicles may have a LOW ENGINE OIL LEVEL warning message and a CHECK ENGINE light illuminated in the instrument cluster, along with DTC P250F:00 stored in memory. DTC P250F:00 - Engine oil level signal: engine oil level low. Upon inspecting the engine oil level, the level is found to be low and there doesnt appear to be any trace of oil leakage in the engine compartment. This concern usually occurs when the mileage reaches approximately 3,100 4,700 miles (5,000 - 7,500km) and may also occur again after replacing or topping off the engine oil. The root cause of this concern has not been identified yet, therefore a repair procedure will be announced at a later date. Since this issue has been reported after a valve stem seal modification, it is very likely that valve stem seal damage is causing oil to leak into the combustion chamber.

NHTSA · メーカー通報10203724モデルイヤー 2021原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda3 IV · 2019–
技術通報中程度ボディNA

技術通報

Some vehicles may have a LOW ENGINE OIL LEVEL warning message and a CHECK ENGINE light illuminated in the instrument cluster, along with DTC P250F:00 stored in memory. DTC P250F:00 - Engine oil level signal: engine oil level low. Upon inspecting the engine oil level, the level is found to be low and there doesn't appear to be any trace of oil leakage in the engine compartment. This concern usually occurs when the mileage reaches approximately 3,100 - 4,700 miles (5,000 - 7,500km) and may also occur again after replacing or topping off the engine oil. The root cause of this concern has not been identified yet, therefore a repair procedure will be announced at a later date. Since this issue has been reported after a valve stem seal modification, it is very likely that valve stem seal damage is causing oil to leak into the combustion chamber.

NHTSA · メーカー通報10202685モデルイヤー 2021原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda3 IV · 2019–
技術通報中程度電装NA

技術通報

Connected vehicle remote functions inoperative and/or engine no start due to low battery voltage. NOTE: SA-045/21 HAS BEEN SUPERCEDED TO SSPC7.

NHTSA · メーカー通報10200938モデルイヤー 2021原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda3 IV · 2019–
技術通報中程度電装NA

技術通報

Connected vehicle remote functions inoperative and/or engine no start due to low battery voltage. Some customers may experience the following symptoms: Connected Vehicle Remote Functions inoperative after SSPC6 repair. Connected Vehicle Remote Functions inoperative on vehicles built March 20, 2021 and later.

NHTSA · メーカー通報10200937モデルイヤー 2021原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda3 IV · 2019–
技術通報中程度電装NA

技術通報

Connected vehicle remote functions inoperative and/or engine no start due to low battery voltage. Some customers may experience the following symptoms: Connected Vehicle Remote Functions inoperative after SSPC6 repair. Connected Vehicle Remote Functions inoperative on vehicles built July 1, 2021 and later.

NHTSA · メーカー通報10200935モデルイヤー 2021原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda3 IV · 2019–
技術通報中程度電装NA

技術通報

Connected vehicle remote functions inoperative and/or engine no start due to low battery voltage. Some customers may experience the following symptoms: Connected Vehicle Remote Functions inoperative after SSPC6 repair. Connected Vehicle Remote Functions inoperative on vehicles built July 1, 2021 and later.

NHTSA · メーカー通報10200934モデルイヤー 2021原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda3 IV · 2019–
技術通報中程度電装NA

技術通報

Some customers may experience the following symptoms: Connected Vehicle Remote Functions inoperative after SSPC6 repair. Connected Vehicle Remote Functions inoperative on vehicles built July 1, 2021 and later. Engine no start due to low battery voltage.

NHTSA · メーカー通報10199636モデルイヤー 2021原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda3 IV · 2019–
技術通報中程度ブレーキNA

技術通報

Some customers may experience an instrument cluster warning message "Safety and Driver Support Systems Partially Disabled" and DTC U0401:68 [VEHICLE CONTROL MODULE (US)] (Error signal received from PCM, DSC HU/CM, instrument cluster, or body control module (BCM)) stored. This may be caused by the customer riding the brake pedal.

NHTSA · メーカー通報10194774モデルイヤー 2019原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda3 IV · 2019–
技術通報中程度ブレーキNA

技術通報

Some vehicles may have a "Low Battery Risk. Start Vehicle to Charge 12V Battery" warning message in the instrument cluster and a 30 second alarm sound. This may be caused by the customer doing any one of the following several times without starting the engine for an extended period of time: Open any door(s), Unlock doors, Open liftgate, Depress brake pedal, Push start/stop button. No dealer visit is required. The warning message can be cleared by starting the engine and idling or driving for 5 minutes or longer.

NHTSA · メーカー通報10186807モデルイヤー 2021原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda3 IV · 2019–
技術通報中程度ブレーキNA

技術通報

INSTRUMENT CLUSTER WARNING MESSAGE "SAFETY AND DRIVER SUPPORT SYSTEMS PARTIALLY DISABLED" AND DTC U0401:68 IS STORED:Some customers may experience an instrument cluster warning message "Safety and Driver Support Systems Partially Disabled" and DTC U0401:68 [VEHICLE CONTROL MODULE (US)] (Error signal received from PCM, DSC HU/CM, instrument cluster, or body control module (BCM)) stored. This may be caused by the customer riding the brake pedal.

NHTSA · メーカー通報10170828モデルイヤー 2019原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda3 IV · 2019–
技術通報中程度ブレーキNA

技術通報

WARNING MESSAGE SAFETY AND DRIVER SUPPORT SYSTEMS PARTIALLY DISABLED WITH DTC U2511:68: Some customer's may compain about warning message "Safety And Driver Support Systems Partially Disabled" with the following DTC's stored: U2511:68 DSC - Error signal received from electrical supply unit (ESU) U2511:68 VCM - Brake light control signal error. REPAIR PROCEDURE: U2511:68 DSC - Error signal received from electrical supply unit (ESU) Go to DTC U2511:68 [DSC HU/CM] U2511:68 VCM - Brake light control signal error Information is currently missing from Workshop Manual. MGSS will be updated soon. See service information below:

NHTSA · メーカー通報10170826モデルイヤー 2019原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda3 III · 2013–2018
技術通報中程度電装NA

技術通報

If you experience issues with the current version of ID's such as missing tools or modules not showing after completing a network test, be advised that we are aware of these issues and are working to resolve them. As a counter measure, it is advised that you un-install ids and re-install version 103.00 and "do not update" until further notice.

NHTSA · メーカー通報10185813モデルイヤー 2017原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda3 III · 2013–2018
技術通報中程度サスペンションNA

技術通報

On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing new lug nuts or the accessory Wheel Lock Set, make sure to use the appropriate part number for the vehicle you are working on. NOTE: The Mazda3 produced in Mexico is not affected. Use the GEPC or the Mazda Accessory web site [MXConnect (dealers.mazdausa.com)] to look up the correct part number for the vehicle you are working on.

NHTSA · メーカー通報10168119モデルイヤー 2018原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda3 IV · 2019–
技術通報中程度電装NA

技術通報

Some vehicles may exhibit DTC B14F0:76 [VCM] (Forward sensing camera (FSC) deviation) stored in memory and the i-ACTIVSENSE warning light (amber) on after BCM replacement. This is caused by the learning value of the forward sensing camera (FSC) aiming being initialized after BCM replacement due to a software malfunction of the FSC. To correct this concern, the FSC software will be modified to not initialize the value of the FSC aiming after BCM replacement.

NHTSA · メーカー通報10166849モデルイヤー 2019原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda3 IV · 2019–
技術通報中程度電装NA

技術通報

If a customer comes in with the following concerns, contact Hotline for assistance. OIL PRESSURE WARNING light and/or the CHECK ENGINE light ON, DTC P055F and/or P0524 stored, No drivability concern or engine mechanical noise, Outside the VIN range in TSB 01-020/18.

NHTSA · メーカー通報10165353モデルイヤー 2019原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda3 IV · 2019–
技術通報中程度ブレーキNA

技術通報

Some customer may experience all of the following when turning the ignition ON under hot weather conditions such as parking under the hot sun for some period of time: i-ACTIVSENSE warning light ON (1), Smart Brake Support (SBS) indicator light ON (2), "Excessive Camera Temp. Drive Safely" or "Safety and Driver Support Systems Temporarily Disabled" warning messages, DTC B14F9:00 stored in memory. DTC B14F9:00 cannot be found on MGSS, therefore repair cannot be performed.

NHTSA · メーカー通報10164053モデルイヤー 2019原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda3 IV · 2019–
技術通報中程度電装NA

技術通報

Some vehicles may exhibit DTC U2120:00 and/or U2500:82 stored in memory and the i-ACTIVSENSE warning light (amber) ON when turning ON the ignition after any electronic control unit (ECU) is reprogramed or configured using MDARS. NOTE: ECU stands for general units (cameras and modules), all of which can be reprogrammed. This is caused by a software malfunction of the forward sensing camera (FSC). To correct this issue, the FSC software will be modified.

NHTSA · メーカー通報10164075モデルイヤー 2019原文(英語)で表示中 · 翻訳待ち詳細を見る →
古いもの →

出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)、国土交通省(日本、公共データ利用規約1.0)、韓国国土交通部(car.go.kr)。