Engine: problems reported by owners
93 owners in the United States reported problems with the engine of this car to NHTSA (model years 2016–2023), typically at around 23,000 miles. Reported consequences: 10 fires, 1 injury.
🔔 無料アカウントを作成して Mercedes-Benz Eクラス V213 のメール通知を受け取る
このファイルには、Mercedes-Benz Eクラス V213で知られている不具合を、コミュニティが出典付きでまとめています。閲覧は無料、投稿には無料アカウントが必要です。信頼できる投稿者が十分に確認した不具合にはシールが付きます。
93 owners in the United States reported problems with the engine of this car to NHTSA (model years 2016–2023), typically at around 23,000 miles. Reported consequences: 10 fires, 1 injury.
84 owners in the United States reported problems with the electrical system of this car to NHTSA (model years 2016–2023), typically at around 18,000 miles. Reported consequences: 6 fires, 3 injuries.
57 owners in the United States reported problems with the airbags of this car to NHTSA (model years 2016–2019), typically at around 10,000 miles. Reported consequences: 7 crashes, 6 injuries.
공급업체의 생산 공정의 편차로 인해 시간이 지남에 따라 드라이브 샤프트의 유니버셜 조인트가 마모될 수 있으며, 이로 인해 유니버셜 조인트에서 윤활유 손실이 발생하여 유니버셜 조인트가 파손될 수 있음. 그 결과로 트랜스퍼 케이스와 전륜 구동 장치 간의 연결이 끊어져 추진력을 잃을 수 있고 충돌 위험이 증가할 수 있음이 확인됨에 따른 리콜 <대상차량별 생산일자> S 450 4MATIC: 2018.01.25~2019.11.14 S 560 4MATIC: 2019.08.30~2019.09.12 CLS 400 d 4MATIC: 2019.02.25~2019.04.11 S 350 d 4MATIC: 2019.04.09 E 450 4MATIC: 2019.02.05 S 400 d 4MATIC: 2017.12.11
Mercedes-Benz AG has determined that on certain 4MATIC E-Class (213 platform) S-Class Coupé (217 platform) S-Class (222 platform) E-Class Coupe/Convertible (238 platform) GLC (253 platform) and CLS (257 platform) vehicles increased wear of the universal joint on the drive shaft might occur.
De drie aluminium schroeven waarmee de power-pack aan de stuurinrichting is bevestigd, kunnen door blootstelling aan water en strooizout roesten.
Complaint Diverse functional limitations in the vehicle in combination with various warning and fault messages in the instrument cluster display. Cause Communication timeouts mean that communication errors may occur in the onboard electrical system, which can result in various fault messages being displayed in the instrument cluster. This could be down to delayed feedback from the drivetrain control unit (N127) (CPC) to other control units networked to the CAN bus. Information: Only valid for vehicles through production period 10/2025. Not valid for vehicles with control unit CDCC (N125, central controller charging and driving) It may not be possible to attribute any communication errors stored in the control units on the CAN bus to a specific cause In rare instances, there may be a brief activation of the yellow warning lamp for engine diagnosis or there may be a sporadic delay with the start enable. There may not be any specific fault codes present that indicate a specific component. Example image: Fault messages in instrument cluster: The reason for this could be down to delayed feedback from the control unit CPC3 to other control units networked on the CAN bus. Remedy Do not replace any components!!! ******************************************************************************************************* 1. Connect charger (see AR54.10P1127WT). Note: An adequate voltage from the onboard electrical system battery must be guaranteed for the entire duration of the work procedure. Otherwise, the control units could be damaged if an undervoltage occurs. Information: Observe the operating instructions of the charger. Information: Use the charger to ensure an adequate voltage (at least 12.5 V) from the onboard electrical system battery. 2. Connect diagnostic system (see AD00.00P200006FR). Note: Always use the latest XENTRY Diagnostics software release. Information: Strict compliance with the operation steps in XENTRY Diagnostics is absolutely essential. 3. Select control unit N127 (CPC) via the direct link using XENTRY Diagnosis. Information: To do so, select the following menu items: Control units view Drive systems N127 "Drivetrain" control unit (CPC) 4. Update software for control unit N127 (CPC) (see AR54.21P001401Y). Info: To do so, select the following menu items: Adaptations Control unit update Update control unit software. Information: You are then automatically guided through the steps "Update of control unit software" and "SCN coding". Always observe the following operation steps at all times 5. Disconnect diagnostic device from vehicle (see AD00.00P200006FR). 6. Disconnect charger from vehicle (see AR54.10P1127WT).
**苦情**: ドア内のスピーカー付近からカチャカチャという異音がする。 **原因**: 調査中。 **対策**: 原因を絞り込むため、まずドアトリムを取り外してください。ドアトリムを取り外しても異音が続く場合は、スピーカーに向けて診断を続けてください。必要に応じて、わかりやすい動画を添付してTIPSケースを作成してください。 **注意**: 保証請求の際はこの文書を参照してください。診断完了後、問題の原因となっている部品に応じてダメージコードを選択してください。ドアトリムを取り外すと異音が止まる場合は、LI72.10P067691に従って対応してください。 **情報**: 今回のケースでは、保証請求にスピーカーのダメージコードを使用しないでください。
Complaint Slight creaking noises when steering. Cause Noises may come from one or more sleeves of the horn contact plate. Remedy Remove the horn contact plate and check the sleeves for noise; see attached video. If necessary, apply lubricant to the sleeves.
出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)、国土交通省(日本、公共データ利用規約1.0)、韓国国土交通部(car.go.kr)。