The front sleeve bushings of the cooling fan motors are susceptible to excessive corrosion in areas of high road salt use. This may increase the rotational friction of the fan motor or result in seizure of the armature shaft to the bushing. Either condition may draw current in excess of that of a normally operating motor but less than required to operate the fuse link. This could overheat the motor wiring circuitry and possibly result in an underhood or instrument panel fire. Vehicles affected: Cars not equipped with factory air conditioning. Quebec and atlantic provinces only.
During a crash barrier test, the rubber hose connecting the fuel tank and the metal filler pipe vent tube was cut, resulting in fuel leakage. The involved vehicles fail to comply with federal motor vehicle safety standard no. 301, "fuel system integrity".
Metal fasteners used to secure the carpeting to the floor pan may have been milocated and may have penetrated the top of the fuel tank. This condition may allow fuel leakage.
On certain vehicles, metal fasteners that were used to secure the carpeting to the floor pan may have accidentally penetrated the top of the fuel tank. This would result in a slight fuel leak.
Vehicles equipped with air conditioning may have the main engine compartment wire assembly incorrectly routed above the air conditioning suction hose such that the wire assembly contacts the hood prop-up bracket attaching bolt. This condition may result in chafing of the wiring insulation possibly causing an electrical short circuit that may result in an engine compartment fire.
On certain vehicles, the right and left hand rear brake backing plate attachment bolts may not have been tightened to the correct specifications. Backing plate bolts may not be able to withstand the loads experienced during truck shipment. If the bolts loosen from the spindle during operation, backing plate movement may result in weakening or premature wear of one or both rear brake tubes. This could lead to loss of brake fluid.
These vehicles may not comply with C.M.V.S.S. 1103 - 排気ガス規制. The central fuel injector (CFI) may operate rich during certain operating conditions. 是正措置: 改良型CFIフューエルインジェクターを取り付け、アイドル回転数を調整します。
The forward screw which provides part of the attachment between the driver`s seat back assembly and the seat cushion frame could fracture and permit the driver's seat back to pivot rearward. Such a condition could adversely affect the driver's ability to control the vehicle and could result in a vehicle crash. Correction: New driver's seat cushion attachment screws will be installed on affected vehicles.
The rear seat belt retractors may allow twisted webbing to enter the retractor housing. Twisted webbing may wedge between the retractor spool and housing producing a jammed retractor condition which interfered with webbing retraction and withdrawal.
Rear seat belt retractors may allow twisted webbing to enter the retractor housing and jam the retractor. Consequence of defect: A jammed retractor would interfere with webbing retraction and withdrawal. This will discourage seat belt usage.
The throttle lever may not return to idle position due to misalignment of the air conditioner shut off switch to the throttle lever pin. Consequence of defect: A jammed throttle could result in a loss of accelerator control, without prior warning, and an accident.
Vehicles with 1.9l engine and air conditioning. A pin located on the throttle lever which actuates the air-conditioner shut-off switch may be subject to misalignment such that the switch could jam behind the actuating arm of the switch. If this were to occur, the throttle lever would be prevented from returning to the idle position and vehicle control could be adversely affected.
On vehicles with optional front seat recliners, the upper shoulder screw that attaches the driver's seat back frame to the recliner mechanism may be susceptible to fatigue fracture. If fatigue fracture of the recliner upper attachment screw were to occur on the driver's seat, the seat back could rotate rearward to a near horizontal position without warning potentially affecting the driver's control of the vehicle.
When severely loaded by a frontal impact, the seat belt webbing may contact the leading edge of the front seat-back stell reinforcement plates. This may cause the seat belt webbing to be abraded, cut or completely severed, thereby significantly increasing the risk of serious personal injuries.
出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)、国土交通省(日本、公共データ利用規約1.0)、韓国国土交通部(car.go.kr)。