技術通報
Due to a manufacturing defect, the left charge air line can fail and cause an induction leak. In some casesthe Engine Malfunction warning may illuminate.
🔔 無料アカウントを作成して Mini ハッチ III のメール通知を受け取る
技術サービス通報(TSB)は、既知の不具合についてメーカーが販売店に送る修理指示です。安全リコールではありませんが、不具合の裏付けになることがよくあります。
Due to a manufacturing defect, the left charge air line can fail and cause an induction leak. In some casesthe Engine Malfunction warning may illuminate.
The left charge air line can fail and cause an induction leak. In some cases the Engine Malfunctionwarning may illuminate. Note: This Service Information is similar to M11 03 23; though this one pertains to vehicles already retailed.
B38 Engine: Mixture Faults Stored in DME and Cylinder Head Cover Leaking Engine Oil
During the vehicle's operational life, normal engine oil seepage or sweating, in addition to accumulated road dust, dirt and grime in the engine compartment can give an appearance that there is an active engine oil leak. This is further exaggerated by residual oil that remains on the engine assembly after maintenance services are performed, for example, oil filter changes, engine oil top-offs, etc. If this visual appearance of accumulated oil on the engine assembly is misinterpreted as an active engine oil leak, then unnecessary gasket repairs/replacements will result.
SERVICE ACTION - MOUNTING THE OIL FILLER CAP CORRECTLY: The oil filler cap may not be mounted correctly. The cap was not installed correctly during assembly.
SERVICE ACTION - MOUNTING THE OIL FILLER CAP CORRECTLY: The oil filler cap may not be mounted correctly. The cap was not installed correctly during assembly.
ENGINE STALLS AFTER STARTING OR WILL NOT START. The engine stalls right after starting (when stationary).
VANOS AND VANOS CENTRAL BOLT IDENTIFICATION. INFORMATION Replacing the VANOS gear central bolts or the VANOS gear will require a component inspection when the engine assembly has been previously replaced in one of the vehicles listed above. Ordering the parts via the model, production or VIN may provide the incorrect part numbers. The procedure below will help identify which VANOS parts are installed in the replacement engine. 11 36 7 608 788 Inlet adjustment unit Oulet adjustment unit Refer to the ETK and the repair instructions for one time use fastener and component information regarding additional screws, gaskets and seals.
SI M11 03 15 February 2016 Engine Technical Service This Service Information bulletin supersedes SI M11 03 15 dated April 2015. SUBJECT B38 Engine: Mixture Faults Stored in DME and Cylinder Head Cover Leaking Engine Oil.
SI M11 03 15 February 2016 Engine Technical Service This Service Information bulletin supersedes SI M11 03 15 dated April 2015. SUBJECT B38 Engine: Mixture Faults Stored in DME and Cylinder Head Cover Leaking Engine Oil.
SI M11 03 15 February 2016 Engine Technical Service This Service Information bulletin supersedes SI M11 03 15 dated April 2015. SUBJECT B38 Engine: Mixture Faults Stored in DME and Cylinder Head Cover Leaking Engine Oil.
SI M11 03 15 February 2016 Engine Technical Service This Service Information bulletin supersedes SI M11 03 15 dated April 2015. SUBJECT B38 Engine: Mixture Faults Stored in DME and Cylinder Head Cover Leaking Engine Oil.
SI M11 03 15 February 2016 Engine Technical Service This Service Information bulletin supersedes SI M11 03 15 dated April 2015. SUBJECT B38 Engine: Mixture Faults Stored in DME and Cylinder Head Cover Leaking Engine Oil.
SI M11 03 15 February 2016 Engine Technical Service This Service Information bulletin supersedes SI M11 03 15 dated April 2015. SUBJECT B38 Engine: Mixture Faults Stored in DME and Cylinder Head Cover Leaking Engine Oil.
"N14 and N18 Engine: High-pressure Pump Repair Instruction. INFORMATION The current version of ISTA/D Repair Instruction 13 51 017, ""Removing and installing or replacing high-pressure pump (N14, N18)"" has a procedure error. The current version of the Repair Instruction states to replace the highpressure supply hose on the N14 engine. The Repair Instruction also states not to replace the high-pressure supply hose on the N18 engine. The N18 portion of the Repair Instruction is incorrect. As an interim solution, follow the procedure outlined below until this portion of the Repair Instruction is corrected. https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/15601.2.M130113... 8/30/2013 Page 2 of 2 All vehicles equipped with the N18 engine and produced from 3/2012 and later. When the engine is fitted with a Bosch High-pressure Pump (1) the highpressure supply hose (2) MUST NOT be replaced when making repairs. The remaining portion of the Repair Instruction and tightning torques are correct. Refer to EPC for the applicable part numbers when making repairs. "
"N14 and N18 Engine: High-pressure Pump Repair Instruction. INFORMATION The current version of ISTA/D Repair Instruction 13 51 017, ""Removing and installing or replacing high-pressure pump (N14, N18)"" has a procedure error. The current version of the Repair Instruction states to replace the high-pressure supply hose on the N14 engine. The Repair Instruction also states not to replace the high-pressure supply hose on the N18 engine. The N18 portion of the Repair Instruction is incorrect. As an interim solution, follow the procedure outlined below until this portion of the Repair Instruction is corrected. https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/159...2/5/2014 Page 2 of 2 Bosch High-pressure Pump (1): All vehicles equipped with the N18 engine and produced from 3/2012 and later When the engine is fitted with a Bosch High-pressure Pump (1), the highpressure supply hose (2) MUST NOT be replaced when making repairs. The remaining portion of the Repair Instruction and tightening torques is correct. Refer to EPC for the applicable part numbers when making repairs."
ENGINE CRANKS, NO START AND/OR ENGINE COOLANT TEMPERATURE FAULTS: NOTE: The engine may also exhibit the same starting behavior as in Situation1.
JCW ENGINE TUNING KIT - ENGINE LOSS OF POWER IN STOP-AND-GO DRIVING: The engine may lose power if the vehicle is decelerated, in gear, to a near stop and then accelerated again.
Mini: The oil filter housing assembly is leaking engine oil and/or coolant. No model or years listed. *pe
ターボチャージャーの返品
During a vehicle inspection and/or while addressing a customer's concern, the engine stabilizer bar/link appears to be worn.
Mini parts logistics TEC 26 turbo charger return
Service action: B46 AND B48 ENGINES - CHECK AND REPLACE CRANKSHAFT GUIDE BEARING
B38, B46 and B48 Engines: Engine Replacement Procedures
Engine will not start (no crank). The engine will not crank or the engine loses power while driving, followed by a no crank situation.
出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)、国土交通省(日本、公共データ利用規約1.0)、韓国国土交通部(car.go.kr)。