閲覧無料 · 投稿は無料アカウントでAnticars(2000年)の後継

Mini ハッチ

2001– · 5 世代 · 不具合50件 · 3市場
世代

技術サービス通報(TSB)は、既知の不具合についてメーカーが販売店に送る修理指示です。安全リコールではありませんが、不具合の裏付けになることがよくあります。

年式
ハッチ III · 2013–2024
技術通報中程度トランスミッションNA

技術通報

"B38, B46, and B48 Engines: Engine Noise, Drivability Complaints, and Various DME Faults. The vehicle exhibits one the following complaints: z Noise from the lower engine area, described as a high-pitched whine z Loss of power when idling z At a higher engine speed (above 3,000 rpm), a brief decrease in the engine speed can be felt. z Extended cranking before the engine will start z The customer notices an increased level of ""free play"" in the clutch pedal when changing gears. z The clutch pedal remains depressed, and will not return to the disengaged position. z Emergency operation is active, with one or more of the faults listed below. One or more of the following faults may be stored in the vehicle: z 160020 Crankshaft sensor, signal: implausible z 180001 Catalytic converter: efficiency too low z 200D0C Powertrain, safety function: bus signal rpm reduction implausible z 11A002 Fuel high pressure, plausibility: Pressure too low z 1F054D Powertrain, safety function: powertrain reduced power, DSC-signal implausible Note: If additional faults are found in the DME memory (e.g., misfire, camshaft sensor, knock sensor, etc.), then those faults will be the primary focus of the diagnosis using the test plans provided for those faults. ""FC 120408 Boost pressure control: Shut-down as a consecutive reaction"" is only a result of the component fault and is not the primary reason for the complaint or https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/286...1/4/2016 Page 2 of 2 illumination of the engine malfunction warning."

NHTSA · メーカー通報10147907モデルイヤー 2016原文(英語)で表示中 · 翻訳待ち詳細を見る →
ハッチ III · 2013–2024
技術通報中程度トランスミッションNA

技術通報

"B38, B46, and B48 Engines: Clutch Operation, Engine Noise, and Drivability Complaints. The vehicle exhibits one the following complaints: z The customer notices an increased level of ""free play"" in the clutch pedal when changing gears. z The clutch pedal remains depressed and will not return to the disengaged position. z Noise from the lower engine area described as a high-pitched whine z Loss of power when idling z At a higher engine speed (above 3,000 rpm), a brief decrease in the engine speed can be felt. z Extended cranking before the engine will start z Emergency operation is active with one or more of the faults listed below. One or more of the following faults may be stored in the vehicle: z 160020 Crankshaft sensor, signal: implausible z 180001 Catalytic converter: efficiency too low z 200D0C Powertrain, safety function: bus signal rpm reduction implausible z 11A002 Fuel high pressure, plausibility: Pressure too low z 1F054D Powertrain, safety function: powertrain reduced power, DSC-signal implausible Note: If additional faults are found in the DME memory (e.g., misfire, camshaft sensor, knock sensor, etc.), then those faults will be the primary focus of the diagnosis using the test plans provided for those faults. ""FC 120408 Boost pressure control: Shut-down as a consecutive reaction"" is only a result of the component fault and is not the primary reason for the complaint or illumination of the engine malfunction warning."

NHTSA · メーカー通報10147908モデルイヤー 2016原文(英語)で表示中 · 翻訳待ち詳細を見る →
ハッチ III · 2013–2024
技術通報中程度トランスミッションNA

技術通報

"?SI M12 04 15 Engine Electrical Systems June 2015 Technical Service This Service Information bulletin supersedes SI M12 04 15 dated March 2015. designates changes to this revision SUBJECT B38, B46, and B48 Engines: Engine Noise, Drivability Complaints, and Various DME Faults. The vehicle exhibits one the following complaints: ? Noise from the lower engine area, described as a high-pitched whine ? Loss of power when idling ? At a higher engine speed (above 3,000 rpm), a brief decrease in the engine speed can be felt. ? Extended cranking before the engine will start ? The customer notices an increased level of ""free play"" in the clutch pedal when changing gears. ? The clutch pedal remains depressed, and will not return to the disengaged position. ? Emergency operation is active, with one or more of the faults listed below. Faults stored in the vehicle: ? 160020 Crankshaft sensor, signal: implausible ? 180001 Catalytic converter: efficiency too low ? 200D0C Powertrain, safety function: bus signal rpm reduction implausible ? 11A002 Fuel high pressure, plausibility: Pressure too low ? 1F054D Powertrain, safety function: powertrain reduced power, DSC-signal implausible? 120408 Boost pressure control: Shut-down as a consecutive reaction"

NHTSA · メーカー通報10147739モデルイヤー 2016原文(英語)で表示中 · 翻訳待ち詳細を見る →
ハッチ III · 2013–2024
技術通報中程度トランスミッションNA

技術通報

"B38, B46 and B48 Engines: Drivability Complaints with Crankshaft Sensor Fault. The vehicle exhibits one of the following complaints: ? Loss of power when idling ? At a higher engine speed (above 3,000 rpm), a brief decrease in the engine speed can be felt. ? Extended cranking before the engine will start ? The customer notices an increased level of ""free play"" in the clutch pedal when changing gears. ? The clutch pedal remains depressed and will not return to the disengaged position. ? Emergency operation is active with one or more of the faults listed below. Faults stored in the vehicle: ? 160020 Crankshaft sensor, signal: implausible ? 180001 Catalytic converter: efficiency too low ? 200D0C Powertrain, safety function: bus signal rpm reduction implausible ? 11A002 Fuel high pressure, plausibility: Pressure too low ? 1F054D Powertrain, safety function: powertrain reduced power, DSC-signal implausible? 120408 Boost pressure control: Shut-down as a consecutive reaction"

NHTSA · メーカー通報10147698モデルイヤー 2016原文(英語)で表示中 · 翻訳待ち詳細を見る →
ハッチ III · 2013–2024
技術通報中程度トランスミッションNA

技術通報

"B38, B46, and B48 Engines: Clutch Operation, Engine Noise, and Drivability Complaints. The vehicle exhibits one the following complaints: ? The customer notices an increased level of ""free play"" in the clutch pedal when changing gears. ? The clutch pedal remains depressed and will not return to the disengaged position. ? Noise from the lower engine area described as a high-pitched whine ? Loss of power when idling ? At a higher engine speed (above 3,000 rpm), a brief decrease in the engine speed can be felt. ? Extended cranking before the engine will start ? Emergency operation is active with one or more of the faults listed below. Faults stored in the vehicle: ? 160020 Crankshaft sensor, signal: implausible ? 180001 Catalytic converter: efficiency too low ? 200D0C Powertrain, safety function: bus signal rpm reduction implausible ? 11A002 Fuel high pressure, plausibility: Pressure too low ? 1F054D Powertrain, safety function: powertrain reduced power, DSC-signal implausible? 120408 Boost pressure control: Shut-down as a consecutive reaction."

NHTSA · メーカー通報10147224モデルイヤー 2016原文(英語)で表示中 · 翻訳待ち詳細を見る →
ハッチ III · 2013–2024
技術通報中程度トランスミッションNA

技術通報

F54 ALL4: FAULT CODE 440317 STORED IN THE LMV. The following Check Control Message (CCM) is displayed in the instrument cluster: CCM 350: Driving stabilization. Drive at a moderate speed. The following entry is present in the fault memory of the LMV: 440317 - Pump motor: General multiple fault. Further fault memory entries can occur in combination: DSC: 48068C - Transfer box - clutch closed down temporarily, possible overheating. 48078A - All-wheel drive clutch - clutch position open, only front-wheel drive. LMV: 440304 - Pump motor: Current too low Unfavorable software of the longitudinal torque distribution module (LMV).

NHTSA · メーカー通報10146975モデルイヤー 2016–2017原文(英語)で表示中 · 翻訳待ち詳細を見る →
ハッチ III · 2013–2024
技術通報中程度トランスミッションNA

技術通報

Mini: Due to faulty installation of crankshaft sensor, catalytic converter, powertrain, fuel high pressure, and boost pressure control, customer complaints of noise from lower engine, loss of power, decrease in engine speed and depressed clutch pedal. *ma

NHTSA · メーカー通報10059110モデルイヤー 2016原文(英語)で表示中 · 翻訳待ち詳細を見る →
ハッチ II · 2006–2013
技術通報中程度トランスミッションNA

技術通報

Bmw(mini): Transmission - various egs faults caused by wiring harness damage. Difficult to engage the d or r gears from park position; gear shifts are extremely harsh during drive; intermittently the transmission warning light may be displayed. *pe

NHTSA · メーカー通報10026570モデルイヤー 2008原文(英語)で表示中 · 翻訳待ち詳細を見る →
ハッチ III · 2013–2024
技術通報軽微トランスミッションNA

技術通報

A Check Control message displays for Transmission oil service required (ID 2120). This warning can be triggered: From 60,000 miles (95,000 km) to 78,000 miles (125,000 km) After six years: The time interval of six years starts from the production date of the vehicle, not on the day of the first registration or the completion of the pre-delivery check (PDI). If the vehicle is driven more than approx. 1900 miles (3,000 km) after the first CCM, then a second message will be display for Transmission fault! (ID 368).

NHTSA · メーカー通報11032775モデルイヤー 2024原文(英語)で表示中 · 翻訳待ち詳細を見る →
ハッチ III · 2013–2024
技術通報軽微トランスミッションNA

技術通報

The upper crankshaft guide bearing may wear out prematurely. The wear on the guide bearing can cause the clutch pedal to malfunction during shifting.

NHTSA · メーカー通報10216759モデルイヤー 2014原文(英語)で表示中 · 翻訳待ち詳細を見る →
ハッチ III · 2013–2024
技術通報軽微トランスミッションNA

技術通報

The upper crankshaft guide bearing may wear out prematurely. The wear on the guide bearing can cause the clutch pedal to malfunction during shifting.

NHTSA · メーカー通報10216760モデルイヤー 2014原文(英語)で表示中 · 翻訳待ち詳細を見る →
ハッチ III · 2013–2024
技術通報軽微トランスミッションNA

技術通報

When the vehicle is on a lift and wheels are manually spun, a clanking noise is heard from the transmission area.

NHTSA · メーカー通報10206695モデルイヤー 2021原文(英語)で表示中 · 翻訳待ち詳細を見る →
ハッチ III · 2013–2024
技術通報軽微トランスミッションNA

技術通報

EGS FAULTS STORED AFTER AISIN TRANSMISSION REPLACEMENT. Due to hardware changes in the AISIN GA6F21AW or GA8F22AW transmissions.

NHTSA · メーカー通報10163062モデルイヤー 2016原文(英語)で表示中 · 翻訳待ち詳細を見る →
ハッチ III · 2013–2024
技術通報軽微トランスミッションNA

技術通報

The manual transmission gear shift knob easily comes off the shift rod with minimal upward force. The retaining tabs on the shifter knob do not hold securely to the shifter rod.

NHTSA · メーカー通報10152334モデルイヤー 2016原文(英語)で表示中 · 翻訳待ち詳細を見る →
ハッチ III · 2013–2024
技術通報軽微トランスミッションNA

技術通報

"The upper crankshaft guide bearing may wear out prematurely. The wear on the guide bearing can cause the clutch pedal to malfunction during shifting. The Engine Malfunction Warning may be illuminated and a fault will be stored in the DME memory for the crankshaft sensor. Noise may be heard from the lower engine and transmission bell housing area and engine damage can occur in rare occasions. This Service Action involves ""396"" F55 and F56 vehicles produced from January 2014 to February 2015. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader. UN"

NHTSA · メーカー通報10151287モデルイヤー 2015–2016原文(英語)で表示中 · 翻訳待ち詳細を見る →
ハッチ III · 2013–2024
技術通報軽微トランスミッションNA

技術通報

"SI M11 02 16 February 2016 Engine Technical Service This Service Information bulletin supersedes SI M11 02 16 dated February 2016.. The upper crankshaft guide bearing may wear out prematurely. The wear on the guide bearing can cause the clutch pedal to malfunction during shifting. The Engine Malfunction Warning may be illuminated and a fault will be stored in the DME memory for the crankshaft sensor. Noise may be heard from the lower engine and transmission bell housing area and engine damage can occur in rare occasions. This Service Action involves ""382"" F55 and F56 vehicles produced from February 2014 to December 2014. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader. UN"

NHTSA · メーカー通報10151150モデルイヤー 2015–2016原文(英語)で表示中 · 翻訳待ち詳細を見る →
ハッチ III · 2013–2024
技術通報軽微トランスミッションNA

技術通報

?SUBJECT Service Action: Program Control Units (DME) . A Check Control Message could intermittently be displayed indicating a Start/Stop Function failure. Vehicle may not restart after stopping. The following fault is stored in the DME: Fault 20BA20: clutch switch, signal: missing In addition the BDC may have the following fault stored: Fault 804084: clutch switch, plausibility fault compared to CAN signal This can occur if for example 14 gears changes are made, but the upper clutch position switch is only activated 10 times. This difference could occur when the clutch pedal is not being fully released between gear shifts or by resting a foot on the pedal so the upper switch position is not recognized.

NHTSA · メーカー通報10151046モデルイヤー 2016原文(英語)で表示中 · 翻訳待ち詳細を見る →
ハッチ III · 2013–2024
技術通報軽微トランスミッションNA

技術通報

Clutch Is Slipping or Grabbing. The customer states that the clutch is slipping or grabbing.

NHTSA · メーカー通報10150145モデルイヤー 2013原文(英語)で表示中 · 翻訳待ち詳細を見る →
ハッチ III · 2013–2024
技術通報軽微トランスミッションNA

技術通報

B38 and B48 Engines: Grease Residue Found at Bottom of Transmission Bell Housing. INFORMATION While performing repairs to the underside of the vehicle, the technician may notice yellow grease residue has formed on the lowest point of the transmission bell housing near the engine starter. The residue is not related to the engine oil or transmission fluid. The grease was applied to the starter during vehicle assembly. If the residue is noticed, the grease can be wiped away with a shop towel. The residue will stop accumulating after the engine has been operated for a few hundred miles. If the residue were to drip from the bell housing, it would be caught by the under body covering and would not create a customer complaint. In a severe case, some marks may be seen on the engine side of the under body covering. The grease drippings will not be seen on the ground under the vehicle. Do not remove or replace any components.

NHTSA · メーカー通報10148295モデルイヤー 2014原文(英語)で表示中 · 翻訳待ち詳細を見る →
ハッチ III · 2013–2024
技術通報軽微トランスミッションNA

技術通報

"Engine Power Reduction with ""Clutch Damaged"" Faults Stored. A drivetrain malfunction check control message is displayed, prompting the customer to contact the dealer for a service visit. The vehicle drives normally, but fault(s) for a damaged clutch are stored in the DME. ? 1D3101 - Clutch: Damaged, transmittable torque too low ? 1D3201 - Clutch: Severely damaged, transmittable torque too low CAUSE 1. The DME software diagnostic for detecting excessive clutch slip is too sensitive. 2. The clutch is damaged."

NHTSA · メーカー通報10147741モデルイヤー 2016原文(英語)で表示中 · 翻訳待ち詳細を見る →
ハッチ III · 2013–2024
技術通報軽微トランスミッションNA

技術通報

"eAutomatic Transmission Selector Lever Will Not Move Out of Park. The transmission selector lever cannot be disengaged from the ""P"" position. This can occur very randomly and is difficult to reproduce. No faults are stored in the EGS control unit, and no warnings are displayed in the instrument cluster. For the most part, if the vehicle is locked and goes to sleep (the light in the hazard switch goes out), the problem is no longer present. Unfavorable EGS software"

NHTSA · メーカー通報10147111モデルイヤー 2016原文(英語)で表示中 · 翻訳待ち詳細を見る →
ハッチ III · 2013–2024
技術通報軽微トランスミッションNA

技術通報

Service Action: B38 Engine - Check and Replace Crankshaft Guide Bearing. The upper crankshaft guide bearing may wear out prematurely. The wear on the guide bearing can cause the clutch pedal to malfunction during shifting. The Engine Malfunction Warning may be illuminated and a fault will be stored in the DME memory for the crankshaft sensor. Noise may be heard from the lower engine and transmission bell housing area and engine damage can occur in rare occasions.

NHTSA · メーカー通報10146973モデルイヤー 2016原文(英語)で表示中 · 翻訳待ち詳細を見る →
ハッチ III · 2013–2024
技術通報軽微トランスミッションNA

技術通報

Service Action: B46 and B48 Engines - Check and Replace Crankshaft Guide Bearing. The upper crankshaft guide bearing may wear out prematurely. The wear on the guide bearing can cause the clutch pedal to malfunction during shifting. The Engine Malfunction Warning may be illuminated and a fault will be stored in the DME memory for the crankshaft sensor. Noise may be heard from the lower engine and transmission bell housing area and engine damage can occur in rare occasions.

NHTSA · メーカー通報10146867モデルイヤー 2016原文(英語)で表示中 · 翻訳待ち詳細を見る →
ハッチ III · 2013–2024
技術通報軽微トランスミッションNA

技術通報

GROANING NOISE WITH CLUTCH OPERATION. Clutch operation may exhibit the following characteristics: produces a groaning noise, especially when engine is at operating temperature, during stopand-go travel. noise comes from transmission housing. noise can be heard in the interior and exterior of the vehicle. Friction between clutch slave cylinder piston rod end and ball socket (thrust piece).

NHTSA · メーカー通報10146870モデルイヤー 2016原文(英語)で表示中 · 翻訳待ち詳細を見る →
ハッチ III · 2013–2024
技術通報軽微トランスミッションNA

技術通報

Service Action: B38 Engine - Check and Replace Crankshaft Guide Bearing. The upper crankshaft guide bearing may wear out prematurely. The wear on the guide bearing can cause the clutch pedal to malfunction during shifting. The Engine Malfunction Warning may be illuminated and a fault will be stored in the DME memory for the crankshaft sensor. Noise may be heard from the lower engine and transmission bell housing area and engine damage can occur in rare occasions.

NHTSA · メーカー通報10146800モデルイヤー 2016原文(英語)で表示中 · 翻訳待ち詳細を見る →
古いもの →

出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)、国土交通省(日本、公共データ利用規約1.0)、韓国国土交通部(car.go.kr)。