The ammonium nitrate propellant used in the airbag inflator may experience a material alteration over time due to degradation occurring after prolonged exposure to high absolute humidity, high temperatures and high-temperature cycling. In the event of an airbag being deployed, it may deploy too slowly or the excessive internal pressure may cause the inflator body to rupture and metal fragments may pass through the cushion material causing injury to the occupants.
Issue: On certain vehicles, exposure to moisture over time could cause the driver-front airbag not to inflate properly in a crash. In some cases, this could cause an airbag not to fully inflate, while in others it could cause it to deploy with more force than normal. It could also cause the inflator to rupture. If the airbag inflator ruptures, small pieces of metal could be propelled toward vehicle occupants or cause damage to the airbag and prevent its proper function. Safety Risk: In a crash requiring an airbag deployment, the driver-front airbag may not inflate properly or the inflator could rupture. This could create a risk of injury. Corrective Actions: Toyota will notify owners by mail and instruct you to take your vehicle to a dealer to inspect, and if necessary, replace the front driver airbag inflator.
On certain passenger vehicles, the fuel tank check valve, located in the fuel tank inlet pipe, may become separated from the inlet pipe and fall into the fuel tank. If the check valve falls into the tank, fuel may spill from the fuel inlet pipe when the fuel pump automatically shuts off during fueling.
Certain passenger vehicles fail to conform to the requirements of federal motor vehicle safety standard no. 108, 'lamps, reflective devices, and associated equipment.' the luminous intensity of the daytime running lamp (drl) will be modified to meet the standard requirements.
Certain passenger vehicles have the possibility that the recess retains a rubber seal ring, which is located at the end of the cylinder body, and may be corroded due to an improper washing process.
On certain vehicles, the recess that retains the rubber seal ring, which is located at the end of the brake master cylinder body, may be corroded due to an improper washing process. In this condition, brake fluid may leak from the seal, or a small amount of air may enter the master cylinder, which could lead to an increase in stopping distance. Correction: After inspection, if a brake fluid leak from the master cylinder is detected or there is air in the master cylinder, the dealer will replace the master cylinder and the brake booster.
The check valve in the fuel tank inlet that prevents reverse fuel flow is incorrectly fitted on some vehicles . This could cause fuel to spill out when the cap is opened if there is high internal pressure in the fuel tank.
On vehicles equipped with cruise control, the cruise control computer circuit board may develop a fault that may result in high engine speed when the engine is started with the main cruise control switch in the "on" position. If the transmission (particularly automatic) is put in gear and the driver does not press firmly on the brake pedal, the vehicle may suddenly accelerate. This could result in loss of control and a possible crash. Correction: Cruise control computer will be inspected and if necessary, replaced.
Soldered terminals of the cruise control computer may develop cracks due to improper application of the coating to the printed circuit board. Consequence of defect: Continued use of cruise control could lead to complete separation of soldered terminals and circuit failure; engine speed would instantly race and vehicle could suddenly accelerate, possibly resulting in an accident.
The engine alternator pulley may break while the engine is operating. This condition could result in damage to underhood components or injury to service personnel.
Due to a faulty press die used in manufacturing alternator pulleys, pulleys installed on certain vehicles may crack and break during vehicle operation. The battery would then be constantly drained without recharging.
1980 celica, corona and pickup trucks. In incomplete emission control label may cause the ignition timing to be misadjusted. Thus vehicles do not comploy with cmvss 1101 - emission devices.
出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)、国土交通省(日本、公共データ利用規約1.0)、韓国国土交通部(car.go.kr)。