무료 열람 · 무료 계정으로 기여Anticars(2000)의 후속

Audi A4 V

2008–2016 · 결함 3건 · 2개 시장

기술 서비스 공지(TSB)는 제조사가 알려진 문제에 대해 딜러에게 보내는 수리 지침입니다. 안전 리콜은 아니지만 결함을 확인해 주는 경우가 많습니다.

연식
공지보통차체NA

공지

Supersedes Technical Service Bulletin Group 57 number 11-54 dated August 18, 2011. Audi advanced key (keyless entry) is inoperative on all doors, but the engine can be started with the keyless starting system (keyless go). The keyless starting system (keyless go) is a standard feature; Audi advanced key is an optional feature. All vehicles have an engine start-stop button (-E408-) and touch sensor surface on the outer door handles, but this does not mean that the optional Audi advanced key function is installed.

NHTSA · 제조사 공지10128361연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통전장NA

공지

?ANTENNA - A technical problem has occurred. Please contact your Audi dealer" is displayed in the driver information panel when in the SiriusXM band. Audio from the satellite radio is present. DTC 02617 (Satellite antenna) is stored in the radio (address word 56) with fault code 11 (Open circuit). Visually, the MMI and MIB antennas are the same, but each antenna draws a different amount of current. For this reason, if an MIB antenna has been installed on a vehicle with an MMI radio, it causes an open circuit DTC. The open circuit DTC will be set on an MMI radio if the current draw from the antenna falls below 60mA . A MIB antenna draws 55mA (+/- 10mA) 4G0-035-503-K. A MMI antenna draws 110mA (+/- 10mA) 4G0-035-503-J.

NHTSA · 제조사 공지10123772연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

Tire vibration (with originally-installed 245/40 R18 93H Pirelli P6 Four Seasons tires) - Repair Authorization. Customer may report feeling a vibration while driving at highway speeds. This Repair Authorization bulletin only applies to vehicles within the Adjustment coverage period (up to 12/12), has originally-installed 245/40 R18 93H Pirelli P6 Four Seasons tires, tires that have an "AO" marking, and has the PR code HM3. Various parts have been replaced under warranty for the condition noted above, but no issues were identified with these parts.

NHTSA · 제조사 공지10118345연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

On audi vehicles with electromechanical steering manufactured within a specific period, it is possible that the seal on the power steering control unit was not manufactured correctly.

NHTSA · 제조사 공지10106784연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

On audi vehicles with electromechanical steering manufactured within a specific period, it is possible that the seal on the power steering control unit was not manufactured correctly.

NHTSA · 제조사 공지10106763연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미변속기NA

공지

ADDITIONAL MAINTENANCE ITEMS: Perform first at 35,000 miles and thereafter every 40,000 miles. DSG/S tronic - Change ATF oil and replace transmission filter element for clutch hydraulics (A3, S3, TT, TTS, S5, S5 Cabriolet, RS 5, S6, and S7 only) Added: Footnote 3: "For the 8K2 Audi S4 use the MY 2015 maintenance card. This is a push behind vehicle based on the PR code"

NHTSA · 제조사 공지10165519연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미서스펜션NA

공지

Revision to Tires-rotate: 5K only; added "(except R8)"

NHTSA · 제조사 공지10153109연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미전장NA

공지

Major Maintenance Section: CHANGED: "(except Audi A3 e-tron)" to (Audi A3 etron only)" at the end of "Cooling system for electrical components: Check coolant level according to description in ElsaPro" ADDED: "(except A3 e-tron)" at the end of "Cooling system - Check coolant level and add coolant if necessary"

NHTSA · 제조사 공지10133434연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미기타NA

공지

Major Maintenance Section: REMOVED: "Rollover protection: Check function with soft top down (Audi A5 Cabriolet and S5 Cabriolet only)" (Already listed under Time-Sensitive Maintenance Items)

NHTSA · 제조사 공지10133433연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미전장NA

공지

This bulletin provides software update instructions for warning messages in the MMI when a user tries to manually refresh data or the vehicle cannot be locked or unlocked.

NHTSA · 제조사 공지10130743연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미기타NA

공지

This document contains the pre-delivery inspection technician reference document. The Pre-Delivery Inspection Technician Reference Document is designed to be a resource used in hand with the Pre-Delivery Inspection Checklist (PDI). The PDI Checklist has been simplified to make the process more efficient, and in doing so, this document has been created to be used as a reference for checklist items that may have additional information. On the PDI Checklist, you find that certain items have been notated with an asterisk symbol (*), this lets you know that additional information can be found in this Technician Reference Document.

NHTSA · 제조사 공지10128508연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미기타NA

공지

This document contains the Audi delivery guidelines checklist.

NHTSA · 제조사 공지10128466연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미엔진NA

공지

This document contains the Audi maintenance schedule. The intervals shown in this table are based on vehicles operating under normal conditions. In case of severe conditions, such as extremely low temperatures, excessive dust, etc., it is necessary for certain operations to be carried out in between the given intervals. This applies particularly to engine oil changes and the cleaning or replacing of the air cleaner filter element.

NHTSA · 제조사 공지10128461연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미전장NA

공지

This document contains the Audi pre-delivery inspection checklist. All items must be completed prior to customer delivery by an Audi technician. Audi recommends using an Audi approved battery charger to prevent excessive battery discharge during inspection. Refer to the Special functions tab of ODIS Diagnosis using GFF for the PDI function tests. It is advised to start ODIS with the engine running to enable all 5F Test Plans in GFF and also to ensure SVM sees all control units during the SVM check vehicle configuration. For items marked with *, please refer to the PDI Technician Reference Document posted on ServiceNet for additional information.

NHTSA · 제조사 공지10128493연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미기타NA

공지

This document contains the fluid capacity chart.

NHTSA · 제조사 공지10128486연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미전장NA

공지

This document contains the Audi pre-delivery inspection checklist. All items must be completed prior to customer delivery by an Audi technician. Audi recommends using an Audi approved battery charger to prevent excessive battery discharge during inspection. Refer to the Special functions tab of ODIS Diagnosis using GFF for the PDI function tests. It is advised to start ODIS with the engine running to enable all 5F Test Plans in GFF and also to ensure SVM sees all control units during the SVM check vehicle configuration. For items marked with *, please refer to the PDI Technician Reference Document posted on ServiceNet for additional information. This document is in Spanish.

NHTSA · 제조사 공지10128441연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미기타NA

공지

This document contains the Audi delivery guidelines checklist. This document is in Spanish.

NHTSA · 제조사 공지10128440연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미변속기NA

공지

Added to: DSG/S tronic - "Change ATF oil and replace transmission filter element for clutch hydraulics"

NHTSA · 제조사 공지10128250연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미기타NA

공지

This document contains the pre-delivery inspection technician reference document. The Pre-Delivery Inspection Technician Reference Document is designed to be a resource used in hand with the Pre-Delivery Inspection Checklist (PDI). The PDI Checklist has been simplified to make the process more efficient, and in doing so, this document has been created to be used as a reference for checklist items that may have additional information. On the PDI Checklist, you find that certain items have been notated with an asterisk symbol (*), this lets you know that additional information can be found in this Technician Reference Document. This document is in Spanish.

NHTSA · 제조사 공지10124703연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미서스펜션NA

공지

This document contains the Audi tire chain information by vehicle.

NHTSA · 제조사 공지10124694연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미서스펜션NA

공지

This document contains the Audi normal load condition tire pressure table.

NHTSA · 제조사 공지10124693연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미서스펜션NA

공지

This document contains the tire pressure table for Audi vehicles. This document is in Spanish.

NHTSA · 제조사 공지10124692연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미전장NA

공지

This document contains the Audi pre-delivery inspection checklist. All items must be completed prior to customer delivery by an Audi technician. Audi recommends using an Audi approved battery charger to prevent excessive battery discharge during inspection. ALL PDI function tests must be run in Guided Fault Finding (GFF) only. Do NOT use Guided Functions for any PDI related test as these will not be uploaded to the Paperless Server. Refer to the Special functions tab of ODIS Diagnosis for using GFF for PDI function tests. It is advised to start ODIS with the engine running to enable all 5F Test Plans in GFF and also to ensure SVM sees all control units during the SVM check vehicle configuration. For items marked with *, please refer to the PDI Technician Reference Document posted on ServiceNet for additional information.

NHTSA · 제조사 공지10123796연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미엔진NA

공지

This document contains the Audi maintenance schedule. First standard maintenance service at 5,000 miles or 1 year after delivery, whichever occurs first. Standard maintenance services thereafter occur at intervals of 10,000 miles or 1 year after the last standard maintenance service, whichever occurs first. First major maintenance service at 15,000 miles or 2 years after delivery, whichever occurs first. Major maintenance services thereafter occur at intervals of 20,000 miles or 2 years after the last major maintenance service, whichever occurs first. The intervals shown in this table are based on vehicles operating under normal conditions. In case of severe conditions, such as extremely low temperatures, excessive dust, etc., it is necessary for certain operations to be carried out in between the given intervals. This applies particularly to engine oil changes and the cleaning or replacing of the air cleaner filter element.

NHTSA · 제조사 공지10123756연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미엔진NA

공지

This document contains the Audi maintenance schedule. First standard maintenance service at 5,000 miles or 1 year after delivery, whichever occurs first. Standard maintenance services thereafter occur at intervals of 10,000 miles or 1 year after the last standard maintenance service, whichever occurs first. First major maintenance service at 15,000 miles or 2 years after delivery, whichever occurs first. Major maintenance services thereafter occur at intervals of 20,000 miles or 2 years after the last major maintenance service, whichever occurs first. The intervals shown in this table are based on vehicles operating under normal conditions. In case of severe conditions, such as extremely low temperatures, excessive dust, etc., it is necessary for certain operations to be carried out in between the given intervals. This applies particularly to engine oil changes and the cleaning or replacing of the air cleaner filter element.

NHTSA · 제조사 공지10123755연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
이전 →

출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).