무료 열람 · 무료 계정으로 기여Anticars(2000)의 후속

Bentley Arnage

1998–2009 · 1 세대 · 결함 0건 · 2개 시장
세대
연식
리콜심각서스펜션JP

クリップ ボトル/ナッ

ホイールボルトの加工が不適切なため締結力が不足し、ボルトが緩むことがある。そのため、そのまま使用を続けると、ボルトが外れ、最悪の場合、ホイールが脱落するおそれがある。

국토교통성 · 일본2007년 4월 12일1213960연식 2005–2006원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →
리콜심각서스펜션NA

휠: 러그/너트/볼트/스터드

일부 차량에서는 로드휠 고정 볼트가 치수가 맞지 않을 수 있습니다. 이 볼트들이 느슨해질 가능성이 있습니다.

NHTSA · 미국2007년 3월 1일07V071000연식 2005–2006자동 번역 · 원문: 영어자세히 보기 →
리콜심각서스펜션UK

휠이 차량에서 분리될 수 있음

확인된 바에 따르면, 해당 차량에는 치수 사양에 맞지 않는 휠 고정 볼트가 장착되어 있었습니다. 이로 인해 휠 볼트가 느슨해질 수 있으며, 그 결과 휠이 분리될 가능성이 있습니다.

DVSA · 영국2007년 2월 16일R/2007/034연식 2005–2006자동 번역 · 원문: 영어자세히 보기 →
리콜심각서스펜션JP

ホイール

ペイント仕様のホイールにおいて、ボルト穴のテーパ部に誤って塗装してしまったため、当該ボルトが緩むものがある。そのため、そのまま使用を続けると、ボルトが外れ、最悪の場合、ホイールが脱落するおそれがある。

국토교통성 · 일본2006년 3월 30일1212940연식 2004–2005원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →
리콜심각서스펜션NA

Wheels

On certain vehicles, the wheels may have an incorrect finish, which can allow the bolts to loosen.

NHTSA · 미국2006년 2월 10일06V040000연식 2005원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜심각서스펜션UK

Wheel fixing bolts may loosen

Due to the possibility of the road wheels having an incorrect finish the potential exists for the wheel fixing bolts to loosen. This defect could lead to the road wheel becoming detached from the hub.

DVSA · 영국2006년 2월 1일R/2006/024연식 2004–2005원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜심각엔진JP

燃料ホース/パイプ

燃料ポンプの異音対策として改良型の燃料ホースを取り付けられた車両において、燃料ホースの成形加工が不適切なため、使用中に当該燃料ホースの曲げ部および接続部に亀裂が入るものがある。そのため、そのまま使用を続けると、最悪の場合、燃料が漏れるおそれがある。

국토교통성 · 일본2005년 3월 10일1212090연식 1999–2002원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →
리콜심각엔진JP

燃料ホース/パイプ

燃料ホースとパイプを接続するコネクターの構造が不適切なため、リリースリングが整備 中に不用意に押され当該コネクターが外れることがある、また、整備時等に再接続した際 、燃料ホースとパイプが正しく接続されにくく、確実に接続がされないことがある。その ため、そのまま走行を続けると燃料が漏れて、最悪の場合、火災に至るおそれがある。

국토교통성 · 일본2004년 5월 27일1211220연식 2002–2003원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →
리콜심각엔진NA

Fuel System

On certain vehicles, the potential exists, following disconnection, for the quick connector not to be fully re-engaged. This would eventually result in a loss of fuel that, in the presence of an ignition sources, creates a risk of a vehicle fire. Disconnection is a requirement for some service operations. Correction: Dealer will remove the quick release collar, ensure full engagement and fit a safety clip.

캐나다 교통부2004년 3월 12일2004093연식 2002–2004원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜심각브레이크JP

圧力制御伝達部

ブレーキ配管及び燃料配管の取り回しが不適切なものがあるため、ブレーキ配管が燃料配 管またはABS予圧ポンプと干渉し、走行時の振動等によりブレーキ配管または燃料配管 が摩耗するものがある。そのため、接触部が損傷して作動油または燃料が漏れ、制動力が 低下するまたは火災に至るおそれがある。

국토교통성 · 일본2003년 11월 20일1210580연식 2003원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →
리콜심각엔진NA

Fuel system, gasoline:Delivery:Hoses, lines/piping, and fittings

On certain passenger and limousine vehicles, contact can occur between a brake pipe or fuel pipe and the antilock braking system (abs) modulator pump. Should this happen, it could result in eventual abrasive damage to either pipe, leading to possible leakage.

NHTSA · 미국2003년 10월 6일03V367000연식 2002–2004원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜심각브레이크JP

圧力制御伝達部

制動装置において、油圧式制動倍力装置の油圧制御装置と畜圧器とを接続するパイプの先 端の形状が不適切なものがあるため、そのままの状態で使用を続けると、当該接続部より 作動油が漏れ、制動力が低下するおそれがある。

국토교통성 · 일본2003년 5월 20일1210210연식 2002원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →
리콜심각브레이크JP

主ブレーキ一般

制動装置において、リザーバータンクからマスターシリンダへの前輪用ブレーキ液供給パ イプの形状が不適切なため、マスターシリンダ内に混入した微量の空気がリザーバータン クから放出されずに当該パイプ内に溜まり、ブレーキ操作時にマスターシリンダ内に再び 流入することがあり、ブレーキペダルの踏み代が増し、最悪の場合、制動力が低下するお それがある。

국토교통성 · 일본2002년 8월 29일1209690연식 1997–2002원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →
리콜심각엔진NA

Fuel System

On certain vehicles, improperly manufactured fuel feed and return hoses were installed. The position of the crimp securing the rubber hose material to the steel quick release connection may have been improper. If the crimp is not properly position, fuel leakage could occur in the engine compartment. If an ignition source is present, this fuel leakage could result in a fire. Correction: Dealers will replace all feed and return hoses.

캐나다 교통부2001년 3월 30일2001074연식 2000–2001원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜심각엔진JP

燃料ホース/パイプ

原動機室内のゴム製燃料ホース(供給側及び戻り側)の金属製継手部へのかしめ方法が不 適切なため、そのままの状態で使用を続けると、かしめ部より燃料が漏れ、最悪の場合、 排気官に滴下して火災に至るおそれがある。

국토교통성 · 일본2001년 3월 21일1208600연식 2000–2001원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →
리콜심각엔진NA

Fuel system, gasoline:Delivery:Hoses, lines/piping, and fittings

Vehicle description: Passenger vehicles. Improperly manufactured fuel feed and return hoses were installed in some of these vehicles. The position of the crimp securing the rubber hose material to the steel quick release connection may have been improper. If the crimp is not properly position, fuel leakage could occur in the engine compartment.

NHTSA · 미국2001년 2월 14일01V042000연식 2000–2001원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜심각엔진NA

Fuel system, gasoline:Delivery:Hoses, lines/piping, and fittings

Vehicle description: Passenger vehicles. The fuel return pipe in the engine compartment can wear through as the result of repeated contact with the exhaust manifold as the vehicle is driven. If the hose becomes damaged, fuel leakage could occur.

NHTSA · 미국2000년 3월 24일00V092000연식 2000원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통차체JP

車体

格納式ボンネットオーナメントの格納機構に使用されている部品の材質が不適切であり、腐食して動かなくなる場合がある。このため、ボンネットオーナメントが衝撃を受けたときに格納しないおそれがある。

국토교통성 · 일본2010년 10월 22일1217080연식 2006–2009원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통차체UK

보행자 부상 가능성

부식이 쌓여 플라잉 B 마스코트가 충돌 시 제대로 수축되지 않을 수 있습니다. 차량이 보행자와 충돌하고 마스코트가 제대로 수납되지 않으면 보행자가 부상을 입을 수 있습니다.

DVSA · 영국2010년 9월 23일R/2010/143연식 2006–2009자동 번역 · 원문: 영어자세히 보기 →
리콜보통차체NA

구조: 몸통: 후드

벤틀리는 2007-2009년형 아나저, 아나겟, 아나지 RL, 브룩랜즈, 그리고 아주 차량을 리콜하고 있습니다. "b" 보닛 장식의 수납 메커니즘이 부식될 가능성이 있습니다. 이로 인해 차량이 사고에 연루될 때 "b" 보닛 장식이 의도한 대로 접히지 않을 수 있습니다.

NHTSA · 미국2010년 9월 13일10V411000연식 2007–2009자동 번역 · 원문: 영어자세히 보기 →
리콜보통서스펜션JP

緩衝アーム/ロッド

フロントロアアームにおいて、ボールジョイント部のセルフロックナットの加工が不適切なため、走行中の振動等により当該ナットが緩むことがある。そのため、そのまま使用を続けると、ナットが脱落し、最悪の場合、ロアアームが外れ、走行不能になるおそれがある。

국토교통성 · 일본2005년 12월 8일1212720연식 2004–2005원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통서스펜션NA

Suspension:Front:Control arm:Lower ball joint

On certain passenger vehicles, due to the use of a non self-locking nut, the front suspension lower ball joint can become disconnected.

NHTSA · 미국2005년 11월 29일05V546000연식 2005원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통서스펜션NA

Suspension

On certain vehicles, due to the fitment of a nut without the specified self-locking feature, the front lower ball joint may become disconnected. This condition could lead to a loss of directional control and result in a crash. Correction: Dealers will replace the lower ball joint nuts.

캐나다 교통부2005년 11월 23일2005368연식 2005원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통서스펜션UK

Potential loss of directional control

Due to the fitment of a nut without the specified self-locking feature the potential exists for the front suspension lower ball joint to become disconnected. This may lead to loss of directional control.

DVSA · 영국2005년 11월 17일R/2005/169원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
이전 →

출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).