무료 열람 · 무료 계정으로 기여Anticars(2000)의 후속

BMW 7 시리즈 E32

1986–1994 · 결함 5건 · 4개 시장
연식
시장전체NA
리콜심각실내NA

Airbag

On certain 318I, 318IS, 325I, 325IS, 525I, 525IT, 535I, 735I, 735IL, 750IL, 850I and M5, the locking tab for the airbag contact ring in the steering wheel assembly could break without warning. If this happens it is possible that the contact ring wiring could break. This would cause the readiness indicator lamp ("SRS" or "AIRBAG") to illuminate and in such a case the airbag would not be available for deployment in a frontal impact. Correction: Locking tab will be replaced with one of a different design.

캐나다 교통부1996년 10월 7일1996159연식 1991–1992원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜심각실내NA

Air bags:Frontal

The air bag contact ring locking tab located in the steering wheel assembly can break without warning.

NHTSA · 미국1996년 7월 1일96V110000연식 1991–1992원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜심각엔진NA

Fuel System

On certain 318I, 318IC, 318IS, 325IC, 325IS, 325IX, 525I, 535I, 735I and 735IL vehicles, the fuel feed hose could harden and "set" over time due to engine compartment temperatures. If this "setting" occurs, it is possible that seepage between the hose and fitting could result because the clamp cannot provide sufficient sealing force to compensate for the hardening of the hose. Fuel seepage, in the presence of an ignition source, could result in an engine compartment fire. Correction: fuel feed hoses and associated clamps will be replaced with ones of a new design.

캐나다 교통부1994년 5월 30일1994096연식 1989–1993원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜심각엔진NA

Fuel system, gasoline:Delivery:Hoses, lines/piping, and fittings

Feed fuel hoses can harden and "set" over time, allowing a seepage of fuel at the connection between the hose and the engine fitting. The clamp used to hold the hose to the fitting is unable to compensate for the hardening of the feed fuel hose.

NHTSA · 미국1994년 4월 11일94V066000연식 1989–1993원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통실내NA

Heater And Defroster

On certain vehicles, failure of a cooling system component such as thermostat, water pump or fan belt can result in a significant increase in coolant temperature and system pressure. Increased system pressure could result the formation of a crack or separation of a seam in the heater core end piece which would cause hot coolant to be expelled from the heater core. This hot fluid could contact car occupants resulting in possible personal injury and/or fogging of the interior window surfaces. Correction: Radiator cap will be replaced with a new design cap in order to avoid buildup of excessive pressure in the cooling system.

캐나다 교통부1998년 10월 14일1998197연식 1988–1993원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통엔진NA

Engine and engine cooling:Cooling system

Vehicle description: Passenger vehicles. A malfunction or failure of a coolant system component, such as a thermostat, water pump, or fan belt, can result in significantly increased coolant temperature and system pressure. If the indications of a critical overheating condition is not noticed by the driver, it is possible that damage to, or failure of, a coolant system component could occur.

NHTSA · 미국1998년 8월 4일98V178000연식 1988–1993원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통엔진NA

엔진

특정 318IC, 318IS, 318TI, 325I, 325IC, 325IS, 525I, 525IT, 530I, 530IT, 540I, 740I, 740IL, 840CI, M3에서는 크루즈 컨트롤과 스로틀 케이블이 스로틀 하우징의 동일한 스로틀 밸브 작동 레버에 연결되어 있습니다. 어느 케이블의 플라스틱 부싱이 파손되어 외부 케이블 하우징이 부싱에서 분리될 수 있습니다. 크루즈 컨트롤 작동 없이 스로틀 페달을 적용하면 외부 튜브가 부러진 부싱 가장자리에 걸려 스로틀 밸브가 부분적으로 열린 상태로 유지될 수 있습니다. 이런 일이 발생하면 차량이 예상대로 감속하지 못해 충돌이 발생할 수 있습니다. 정정: 각 케이블의 외부 튜브에 스프링 클립이 설치되어 부싱에서 떨어지는 것을 방지합니다.

캐나다 교통부1997년 10월 9일1997173연식 1993자동 번역 · 원문: 영어자세히 보기 →
리콜보통엔진NA

Vehicle speed control

The cruise control and throttle cables are attached to the same throttle valve actuating lever at the throttle housing. It is possible that the plastic bushing on either cable could break due to environmental influences coupled with vibration. If the bushing breaks, the outer cable housing can separate from the bushing. In this case, during application of the throttle pedal without cruise control being engaged, the outer tube could catch on the edge of the broken bushing.

NHTSA · 미국1997년 8월 19일97V131000연식 1993원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통전장NA

Lights And Instruments

On certain 325I, 325IC, 325IS, 525I, 525IT, 530I, 530IT, 535I, 540I, 735I, 735IL, 740I, 740IL and 750I, the brake light switch may fail due to a reduction of contact force on the "snap contact" system which the switch incorporates. This could cause heat induced distortion of the plastic internal switch parts in the area of the electrical contacts. This could cause the switch to remain either in the ON or the OFF position resulting in the brake lights being continuously illuminated or inoperative regardless of brake pedal operation. Correction: Switch will be replaced with on that utilizes a different contact system.

캐나다 교통부1996년 10월 7일1996158연식 1990–1993원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통브레이크NA

Exterior lighting:Brake lights:Switch

The brake light switch can fail allowing the switch to remain in the "brake lights off" position or in the "brake lights on" position.

NHTSA · 미국1996년 7월 1일96V111000연식 1990–1993원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통엔진NA

Engine

On certain 740IA and 740ILA vehicles, the inner throttle cable could break due to a smaller than specification bend in the cable tube. If this were to occur, throttle control would be lost and the engine would return to or remain at idle. Correction: Throttle cable will be replaced with one meeting BMW specifications.

캐나다 교통부1994년 4월 25일1994081연식 1993원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통엔진NA

Vehicle speed control:Cables

The throttle cable's tube (outer casing) contains a bend that leads to increased loading of the inner cable, causing it to break.

NHTSA · 미국1994년 1월 3일94V022000연식 1993원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통엔진NA

Engine

On certain 535I, 535IA, 735IA, 735ILA vehicles, the nut which secures the throttle valve shaft may not have been tightened with sufficient torque. If the nut were to loosen, it is possible that movement of the throttle valve might be impaired. If this should occur, the vehicle might not decelerate as expected after the gas pedal is released and loos of vehicle control could result. Correction: Vehicles will be inspected and affected throttle housings with undertorqued throttle valve retaining nuts will be replaced.

캐나다 교통부1992년 10월 13일1992129연식 1991원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통엔진NA

Vehicle speed control

Some of these vehicles are equipped with a throttle housing on which the throttle valve shaft retaining nut was not sufficiently tightened.

NHTSA · 미국1992년 7월 10일92V101000연식 1991원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통실내NA

Seats And Restraints

On certain 525I, 535I, 735I, 735IL and 750IL vehicles, the front seat center fold-down armrest may contact and damage the seatbelt buckle if the seat back is moved forward to an upright position while the armrest is locked in the down position (horizontal). If this occurs, the release button may be held in the down position, preventing the seatbelt from being latched during the buckle-up operation. Non-latching of the seatbelts will increase the risk of personal injury in the event of a crash. Correction: Front seat safety belt buckles will be replaced with shorter ones that are not susceptible to damage by contact with the armrest.

캐나다 교통부1990년 2월 27일1990037연식 1988–1990원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통실내NA

Seat belts:Front:Buckle assembly

Under certain conditions, front seat center, fold-down arm rest may contact the safety belt buckle, causing damage to the release button and preventing the belt tongue from latching when buckling up.

NHTSA · 미국1990년 1월 30일90V016000연식 1988–1990원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통엔진NA

Emissions

Certain 750IL vehicles fail to comply with the requirements of CMVSS 1103 - Exhaust Emissions.

캐나다 교통부1989년 5월 2일1989063연식 1988–1989원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통엔진NA

Emissions

Certain 750IL vehicles fail to comply with the requirements of CMVSS 1103 - Exhaust Emissions

캐나다 교통부1989년 5월 2일1989062연식 1988–1989원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통엔진NA

Engine

On certain 750IL vehicles, during the assembly process, the gas pedal may not have been properly attached to the floor pan. If the gas pedal is operated in a rough or erratice manner, it may become stuck between the gas pedal stop (on the floor pan) and the carpeting on the transmission tunnel. If this occurs, the pedal might not return fully to the idle position when the driver's foot is removed and loss of control could result. Application of the brake pedal will close the throttle on this model of vehicle. Correction: Accelerator pedal will be inspected and tightened to the floor is required. Also, a modified pedal stop will be installed.

캐나다 교통부1989년 4월 6일1989046연식 1988–1989원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통전장NA

전기

일부 325E, 325ES, 528E, 535I, 635CSI, 735I 차량에서는 중앙 높게 장착된 브레이크등이 충분한 전기 부하를 가해 브레이크등 스위치가 과열되어 결국 플라스틱 내부 스위치 부품이 녹아버릴 수 있습니다. 이로 인해 스위치 플런저가 ON이나 OFF 위치에서 걸릴 수 있습니다. 이로 인해 브레이크 페달 작동과 상관없이 브레이크등이 영구적으로 켜지거나 꺼지는 상태가 됩니다. 정정: 전류 부하 용량이 증가한 브레이크 라이트 스위치가 해당 차량에 설치됩니다.

캐나다 교통부1986년 11월 27일1986134연식 1986–1987자동 번역 · 원문: 영어자세히 보기 →
리콜보통브레이크NA

외부 조명: 브레이크등: 스위치

브레이크등 스위치가 과열되어 결국 전기 접점 부위의 플라스틱 내부 부품이 녹아버릴 수 있었습니다.

NHTSA · 미국1986년 11월 10일86V151000연식 1986–1987자동 번역 · 원문: 영어자세히 보기 →
리콜경미실내NA

Seats And Restraints

On certain 725I, 735IA and 750IL vehicles, on the front seats, the seatbacks may not have been fully seated on the recliner arms. This could result in looseness of, or noise in the seat. In extreme cases, during a severe rear impact, the seatback may not support the occupant and increase the risk of injury. Correction: Seatbacks will be inspected and properly seated if required.

캐나다 교통부1988년 8월 25일1988124연식 1988원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜경미실내NA

Seats

The driver and/or passenger seatbacks may not have been fully attached to the seat base reclining arms (attaching brackets).

NHTSA · 미국1988년 8월 11일88V135000연식 1988원문(영어)으로 표시 중 · 번역 대기자세히 보기 →

출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).