무료 열람 · 무료 계정으로 기여Anticars(2000)의 후속

BMW M3

1986– · 6 세대 · 결함 15건 · 2개 시장
세대

기술 서비스 공지(TSB)는 제조사가 알려진 문제에 대해 딜러에게 보내는 수리 지침입니다. 안전 리콜은 아니지만 결함을 확인해 주는 경우가 많습니다.

연식
시장전체NA
E90/92/93 M3 · 2007–2013
공지심각전장NA

공지

"? NO REGENERATION OF THE DIESEL PARTICULATE FILTER (DPF) This Service Information bulletin supersedes SI B18 03 10 dated November 2010. . The Service Engine Soon lamp is illuminated. The following fault codes may be stored in the DDE: N47T/N57T engine 245700 - Particle filter system: particulate filter highly loaded (Exhaust backpressure high) 245800 - particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) M57Y engine 480A Particle filter system - filter is heavily contaminated. (exhaust backpressure is too high) 481A Particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) CAUSE 1. Faults with the exhaust system that affect the monitoring of the DPF by the DDE 2. Unfavorable recent driving profile INFORMATIOM During normal driving, there is a continuous regeneration of the diesel particulate filter that takes place at exhaust-gas temperatures between 280 and 350C (slower oxidation process). The soot particles can only be burned off when the required exhaust-gas temperature has been reached. Under certain driving conditions (i.e., prolonged short trips or an exhaust system which never reaches soot burn-off temperatures), the DPF can become restricted. The DDE will initiate periodic regeneration automatically, at the latest after 600 miles. In vehicles making many short distance journeys, periodic regeneration takes place after only 250-500 miles. The Digital Diesel Electronics control unit evaluates the time for periodic regeneration from the following values: average distance driven average driving speed temperature in the diesel particulate filter values from the exhaust pressure sensor The DDE initiates the regeneration process by decreasing incoming air by the throttle valve, and one or two post injections are executed. This heats the exhaust-gas temperature to approx. 600 C . When the exhaust temp reaches this point: The soot is burned off with the residual oxygen. The

NHTSA · 제조사 공지10146535연식 2011원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
E90/92/93 M3 · 2007–2013
공지보통전장NA

공지

Butt connector for repairing a plug connection. The ?top up coolant? message is displayed in the central display (CC message ID 166). When checking the cooling system there are no leaks found and the expansion tank is filled to the proper level.

NHTSA · 제조사 공지10193494연식 2013원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
G80 M3 · 2020–
공지보통전장NA

공지

COMFORT ACCESS AND COMFORT GO NOT POSSIBLE: Vehicle cannot be unlocked/locked or started via Comfort Access. Remote control functionality is restored by pressing any of the key buttons or by removing and reinstalling the remote control key battery.

NHTSA · 제조사 공지10179824연식 2020원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
G80 M3 · 2020–
공지보통전장NA

공지

KAFAS04 (CAMERA-BASED DRIVER ASSISTANCE SYSTEMS) LIMITATIONS: Various functions of the KAFAS (without radar installed) are not operating up to customer expectations.

NHTSA · 제조사 공지10175290연식 2020원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
G80 M3 · 2020–
공지보통전장NA

공지

COMFORT ACCESS AND COMFORT GO NOT POSSIBLE: This Service Information Bulletin (Revision 1) replaces SI B66 19 19 dated May 2019. Vehicle cannot be unlocked/locked or started via Comfort Access. Remote control functionality is restored by pressing any of the key buttons or by removing and reinstalling the remote control key battery. The Display Key Digital Key and the Digital Key Card are not affected. Electrostatic discharge puts the remote control key into a deep sleep. Various situations can lead to an electrostatic charge which is often not recognized by the customer. For example walking over carpet wearing shoes that have a hard rubber sole positive and negative charges are exchanged. The sole accumulates a negative charge and an electrostatic charge develops before touching the remote control key.

NHTSA · 제조사 공지10174317연식 2020원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
G80 M3 · 2020–
공지보통전장NA

공지

ENGINE DOES NOT START BELOW FREEZING TEMPERATURES: Engine designation correction Parts availability Warranty. The engine will not start at temperatures below freezing. The starter does not turn and engage.

NHTSA · 제조사 공지10170572연식 2020원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
F80 M3 · 2014–2018
공지보통전장NA

공지

"Service Action: Replace Engine Compartment Sound Insulation. The sound insulation in the engine compartment does not seal properly. Manufacturing tolerances and a defect in workmanship may cause the sound insulation to leak water into the DME wiring connector. AFFECTED VEHICLES This Service Action involves F80 and F82 vehicles produced from March 18, 2014 to May 20, 2014. First check if a Service Action label with a code number 698 is already attached to the B-pillar. If a code number 698 has been punched out, the Service Action has already been performed and no further action is necessary. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader."

NHTSA · 제조사 공지10152310연식 2015원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
E90/92/93 M3 · 2007–2013
공지보통전장NA

공지

N51 Engine: Service Engine Soon Lamp Illuminated - Loss of Power and Various Faults Stored in the DME. The customer complains that the Service Engine Soon lamp is illuminated. The vehicle has lost power; the engine cranks but will not start; and various faults are stored in the DME for engine misfire and/or mixture adaptations. CAUSE The vehicle has lost fuel system delivery pressure due to a loose or split fuel line inside the fuel tank. The failure is related to an unfavorable stacking of tolerances between the rubber fuel hose and the plastic regulator nipple or deterioration of the rubber hose construction material.

NHTSA · 제조사 공지10151170연식 2011원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
E90/92/93 M3 · 2007–2013
공지보통전장NA

공지

Service Action: CIC - Install Navigation Road Map Database 2013. The Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD).

NHTSA · 제조사 공지10150389연식 2011원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
E90/92/93 M3 · 2007–2013
공지보통전장NA

공지

"Service Action: CIC - Install Navigation Road Map Database 2013. Before delivering affected vehicles to the customer, the Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD). Note: The INITIAL enabling code ""FSC CIC map, N. America 2013 INITIAL"" is necessary to start the installation process and to activate the road map database."

NHTSA · 제조사 공지10150334연식 2011원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
E90/92/93 M3 · 2007–2013
공지보통전장NA

공지

N51, N52K, N52T and N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine exhibits a loss of power; and the Service Engine Soon lamp is illuminated. One, or more of the following faults may be stored. E70, E71, E82, E88, E90, E92 and E93: 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D54 - VANOS, exhaust, cold start: not controllable 2D55 - VANOS, intake, cold start: not controllable 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - Camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One, or both (intake and/or exhaust) of the VANOS gear assemblies have failed; the attaching bolts may have also loosened and/or broken.

NHTSA · 제조사 공지10150033연식 2011원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
E90/92/93 M3 · 2007–2013
공지보통전장NA

공지

N51, N52K, N52T and N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine exhibits a loss of power; and the Service Engine Soon lamp is illuminated. One, or more of the following faults may be stored. E70, E71, E82, E88, E90, E92 and E93: 2A7C - VANOS, inlet, cold start 2A82 - VANOS, intake, variable cam control test 2A7A - VANOS, exhaust, cold start 2A87 - VANOS, intake: control fault, camshaft sticking 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D54 - VANOS, exhaust, cold start: not controllable 2D55 - VANOS, intake, cold start: not controllable 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - Camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One, or both (intake and/or exhaust) of the VANOS gear assemblies have failed; the attaching bolts may have also loosened and/or broken.

NHTSA · 제조사 공지10150218연식 2011원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
F80 M3 · 2014–2018
공지보통전장NA

공지

BMW 부품 공지 TEC1T RDC 모듈 반품 BMW NA는 다음 부품 번호에 대한 점검을 요청했습니다: 36 10 6 856 227 및 36 10 6 798 872. 재고는 판매하거나 어떤 차량에도 설치해서는 안 됩니다. 해당 부품을 귀사의 담당 지역 유통센터(RDC)로 반품해 주십시오. 반품 신청은 주문 사유 BM2를 사용하여 YR26 손상 클레임으로 제출하십시오. 유효한 BMW 배송 번호와 배송 품목 번호를 입력해야 하며, TEC 클레임 본문에 TEC1T가 반드시 포함되어야 합니다. TEC1T는 2013년 5월 30일부터 2013년 6월 13일까지 유효합니다. TEC1T에 대한 클레임 제출 기한은 2013년 6월 13일입니다. 모든 부품은 늦어도 2013년 6월 27일까지 담당 RDC로 반품되어야 합니다. 부품 번호 36 10 6 856 227: 인덱스가 02 이하인 모든 부품은 반품해야 합니다. 인덱스가 03인 부품은 정상입니다. 부품 번호 36 10 6 798 872: 인덱스가 03 이하인 모든 부품은 반품해야 합니다. 인덱스가 04인 부품은 정상입니다. 인덱스는 박스 라벨의 바코드 아래에 있는 두 자리 코드입니다. 인덱스는 부품 자체의 부품 번호 바로 뒤에서도 확인할 수 있습니다. 필요한 경우 동일한 부품 번호로 다시 주문하십시오. (c) 2013, BMW of North America, LLC. 이 문서의 내용은 기밀이며 제3자에게 배포 목적으로 공유해서는 안 됩니다.

NHTSA · 제조사 공지10150084자동 번역 · 원문: 영어자세히 보기 →
E90/92/93 M3 · 2007–2013
공지보통전장NA

공지

"N54 Engine: Diagnosis of Cold Start Rough Running with Misfire Faults. The customer may complain that during the cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. Various misfire fault codes (e.g., 29CC, 29D2, 29D1, 29D0, 29C0, 29CF) may be stored in the DME control module. The engine rough running complaint can be reproduced on a cold start in the workshop. During the course of diagnosis, the spark plugs, removed from the misfiring cylinders after the problem was reproduced, are found to be soaked (""wet"") with fuel, while the injector tips are covered with a layer of carbon deposit. Possible cause: high-pressure injector failure (leakage or incorrect spraying pattern) due to internal wear or unfavorable stock of tolerances IMPORTANT: For comprehensive N54 drivability diagnostics, always refer to the ""N54 Engine Diagnostic Fault Tree"" file (the current version ""02_14_13"" is found as a PDF attachment to SI B12 55 06)."

NHTSA · 제조사 공지10149589연식 2011원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
F80 M3 · 2014–2018
공지보통전장NA

공지

CLOSED-CIRCUIT CURRENT MONITORING. Increased closed-circuit currents may occur permanently or intermittently and cause the battery to discharge prematurely. The increase in closed-circuit current may be caused by a faulty control module or by the installation of a non-approved accessory. In a situation where a vehicle has broken down due to a discharged battery, for diagnostic purposes it is important not to disconnect the battery. This is because a control module will be reset if the battery is disconnected. Following a reset, the faulty control module may start functioning correctly again, making accurate diagnosis impossible. To correctly measure closed-circuit current, the 50-amp or 100-amp clip-on probe can be used in conjunction with the IMIB (Integrated Measurement Interface Box) to properly diagnose closed-circuit current problems over an extended period of time.

NHTSA · 제조사 공지10149555원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
E90/92/93 M3 · 2007–2013
공지보통전장NA

공지

?SI B12 14 12 April 2013 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 14 12 dated January 2013. designates changes to this revision SUBJECT N51, N52K, N52T and N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine has a loss of power; and the Service Engine Soon lamp is illuminated. One or more of the following faults may be stored. E70, E71, E82, E88, E90, E92 and E93: 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One or both (intake and/or exhaust) of the VANOS gear assemblies have failed; the attaching bolts may have also loosened and/or broken.

NHTSA · 제조사 공지10149339연식 2011원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
F80 M3 · 2014–2018
공지보통전장NA

공지

2013 MINI JCW Paddle Shifter Retrofit. SZL to EGS harness installation. For necessary preliminary tasks, refer to ISTA and perform the following steps listed in this document.

NHTSA · 제조사 공지10149498원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
E90/92/93 M3 · 2007–2013
공지보통전장NA

공지

N51 Engine: Service Engine Soon Lamp Illuminated - Loss of Power and Various Faults Stored in the DME. The customer complains that the Service Engine Soon lamp is illuminated. The vehicle has lost power; the engine cranks but will not start; and various faults are stored in the DME for engine misfire and/or mixture adaptations. CAUSE The vehicle has lost fuel system delivery pressure due to a loose or split fuel line inside the fuel tank. The failure is related to an unfavorable stacking of tolerances between the rubber fuel hose and the plastic regulator nipple or deterioration of the rubber hose construction material.

NHTSA · 제조사 공지10149349연식 2011원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
E90/92/93 M3 · 2007–2013
공지보통전장NA

공지

N51, N52K, N52T and N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine has a loss of power; and the Service Engine Soon lamp is illuminated. One or more of the following faults may be stored. E70, E71, E82, E88, E90, E92 and E93: 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One or both (intake and/or exhaust) of the VANOS gear assemblies have failed; the attaching bolts may have also loosened and/or broken.

NHTSA · 제조사 공지10149296연식 2011원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
F80 M3 · 2014–2018
공지보통전장NA

공지

NVLD Tank Leakage FC 190302 Fuel Tank Ventilation and Purge Air System Micro Leak. The engine malfunction warning is illuminated and the following fault code is stored in the DME memory: z FC 190302 Fuel tank ventilation and purge air system micro leak leakage greater than 0_5 mm CAUSE Contamination of the NVLD pressure switch electrical contacts

NHTSA · 제조사 공지10148173연식 2015원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
F80 M3 · 2014–2018
공지보통전장NA

공지

Service Action: Bluetooth Software (KISU Data) Update. This Service Action is being released to improve customer satisfaction as we strive to be number 1 in the JD Power Initial Quality Survey (IQS). This new KISU software improves the Bluetooth functionality in our vehicles, and it helps keep us up-to-date with technology innovation. Please implement the Bluetooth Software Update Service Action. This Service Action will be in effect until March 2015. Thank you for your continuous support. Improved KISU data (Customer Initiated Software Update) is now available for installation in these vehicles via the USB port. Improved functionality for COMBOX: z Detailed view of the text messages z Android device connection stability (linked contacts causing BT disconnection) Improved functionality for HU-H: z Reconnection strategy z 3rd Party App Metadata - Album art and song title Note: This Service Action is to be completed only at the dealer. You (dealers) will be receiving vehicles from the VDCs that will require this service action to be completed prior to customer delivery.

NHTSA · 제조사 공지10148195연식 2015원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
F80 M3 · 2014–2018
공지보통전장NA

공지

"Service Action: Replace Engine Compartment Sound Insulation. The sound insulation in the engine compartment does not seal properly. 1.Left side: Turn the locks (1) 90 degrees counterclockwise. Unlock the catch (2) and remove the cover (3). Manufacturing tolerances and a defect in workmanship may cause the sound insulation to leak water into the DME wiring connector. AFFECTED VEHICLES This Service Action involves F80 and F82 vehicles produced from March 18, 2014 to May 20, 2014. First check if a Service Action label with a code number 698 is already attached to the B-pillar. If a code number 698 has been punched out, the Service Action has already been performed and no further action is necessary. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader."

NHTSA · 제조사 공지10148031연식 2015원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
F80 M3 · 2014–2018
공지보통전장NA

공지

N63: Proper Ignition Harness Installation and Ground Connections. INFORMATION https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/16511.1.B12241... 10/14/2014 Page 2 of 2 Any consecutive damage to the BSD interface components (DME, alternator voltage regulator, QLT sensor) caused by incorrect reinstallation of the ignition harness is not covered under the BMW New Vehicle /SAV Limited Warranty.

NHTSA · 제조사 공지10148021원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
F80 M3 · 2014–2018
공지보통전장NA

공지

Battery Maintenance Requirements: Battery Care. Proper battery maintenance is vital when BMW vehicles are in your center's inventory. Allowing a vehicle's battery voltage to drop below 12.0 volts (12.0V) permanently reduces the battery life expectancy and can lead to premature failure of the battery. For vehicles, equipped with a high-voltage battery (hybrid/electric vehicles), failure to properly maintain this battery may lead to a greatly discharged HV battery, requiring replacement. We provide a flexible battery maintenance system every BMW center can use in accordance with their particular needs. This bulletin explains the Battery Charging Calendar (see attachment), charging systems and a simplified tool and battery voltage checking procedure below.

NHTSA · 제조사 공지10148035원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
F80 M3 · 2014–2018
공지보통전장NA

공지

BMW Parts Bulletin TEC9V Fuel Tank / Level Sensor Returns BMW AG has requested an inspection of the following part numbers: 16 11 7 268 031, 16 11 7 268 032 and 16 11 7 297 340 Stock should not be sold or installed on any vehicle. 16 11 7 268 031 and 16 11 7 268 032 All fuel tanks produced before 05/30/2014 needs to be returned. All parts with later dates of production are ok and can be used. 16 11 7 297 340 All level sensors produced in Poland before 05/19/2014 (date is shown as day 139 of year 14 on the part) need to be returned. Those produced after this date are ok and can be used. All level sensors produced in Brazil currently in dealer inventory need to be returned. Please return all part(s) to your facing Regional Distribution Center (RDC). Submit for return using a YR26 damage claim with order reason BM2. A valid BMW delivery and delivery item number must be entered, and TEC9V must appear in the text of your TEC claim. TEC9V is valid from September 24, 2014, through October 08, 2014. The deadline for filing a claim under TEC9V is October 08, 2014. All parts must be returned to your facing RDC no later than October 22, 2014. Please re-order the same part numbers as needed. (c) 2014, BMW of North America, LLC. The contents of this document are confidential and should not be shared with third parties for distribution. Page 2 / 2 Made in Poland Made in Brazil Need to be returned (c) 2014, BMW of North America, LLC. The contents of this document are confidential and should not be shared with third parties for distribution.

NHTSA · 제조사 공지10148044원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
이전 →

출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).