Citroen Cross 차량 라인 연료 분사 커먼레일
차량에 따라 연료 분사 커먼레일의 부적합 문제로 인해 너트가 풀리고 연료 누출이 발생할 가능성이 있습니다.
🔔 무료 계정을 만들고 Citroën Jumpy (모든 세대) 이메일 알림 받기
차량에 따라 연료 분사 커먼레일의 부적합 문제로 인해 너트가 풀리고 연료 누출이 발생할 가능성이 있습니다.
차량 영향 범위 내 차량에서 연료 주입구 캡 근처에 있는 연료 주입구 넥 씰(seal)의 위치가 정상과 다를 가능성이 있으며, 이로 인해 연료 탱크를 가득 채울 때 연료가 누출될 수 있습니다.
해당 차량에서는 특定 조건에서 연료 누설 오프 파이프가 인젝터와의 연결부에서 고정이 느슨해질 수 있습니다. 이 경우 연결부에서 연료가 새어 나올 수 있습니다. 연료가 엔진룸에 고일 수 있으며, 차량 사용자는 연료 냄새를 느끼게 됩니다.
엔진 실린더 헤드가 제조 사양을 충족하지 않을 수 있는 것으로 확인되었습니다. 이로 인해 오일 누유가 발생할 수 있으며, 이를 시정하지 않을 경우 오일이 고온의 엔진 부품에 닿아 화재로 이어질 수 있습니다.
연료 리턴 파이프가 엔진룸의 디젤 연료 필터 지지대에 마찰(쓸림)로 손상될 가능성이 있습니다. 이를 발견하지 못하면 연료 누유로 이어질 수 있습니다.
엔진룸 내부에서 연료 리턴 파이프가 엔진 쉴드와 접촉할 가능성이 있는 것으로 확인되었습니다. 이러한 접촉이 발생하면 파이프가 마모되며, 최악의 경우 연료 누출로 이어질 수 있습니다.
생산 부적합으로 인해 영향을 받는 차량에서는 워터 펌프가 오작동할 수 있으며, 이로 인해 엔진 출력이 저하되고 엔진이 정지될 수 있습니다.
Vehicles may be affected by incorrect performance of the On-Board-Diagnostics related to Selective Catalytic Reduction system and/or Diesel Particle Filter. The Malfunction Indicator Light (MIL) may not illuminate in the event of a malfunction and therefore does not comply with emission regulations.
Some vehicles may have been equipped with an incorrectly positioned fuel pipe.
The cooling system strategy and the maximum temperature alert could cause the engine to overheat this may cause an oil leak from the sump drain cap. Due to the incorrect operation of the warning system there is no driver alert.
On the affected vehicles the tightening of a sealing plug on the engine oil gallery may not be correct to specification.This could lead over time to an oil leak which in rare cases could result in oil leaking on to the road.
An engine component may not be to specification which could result in loss of engine performance. This may lead to the engine stalling and potentially causing an engine failure. In very unlikely circumstances the vehicle speed may increase without warning but will stop on its own after a few seconds.
The fuel filter's integrated heater may be defective and could cause the cover to distort. This could cause air ingress and fuel egress. Either could cause poor starting and a warning light should illuminate
An inadequate weld on the bottom engine mounting tie bar may fail and cause a serious engine vibration and separation of one of the driveshafts.
출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).