무료 열람 · 무료 계정으로 기여Anticars(2000)의 후속

DodgeDodge 니트로

2006–2011 · 1 세대 · 결함 14건 · 3개 시장
세대

기술 서비스 공지(TSB)는 제조사가 알려진 문제에 대해 딜러에게 보내는 수리 지침입니다. 안전 리콜은 아니지만 결함을 확인해 주는 경우가 많습니다.

연식
공지보통기타NA

공지

wiTECH 소형 누출 검증 테스트(SLVT) - P0456 - EVAP 시스템 소형 누출

NHTSA · 제조사 공지10236933연식 2012자동 번역 · 원문: 영어자세히 보기 →
공지보통엔진NA

공지

Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.

NHTSA · 제조사 공지10230180연식 2012원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통엔진NA

공지

Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.

NHTSA · 제조사 공지10221594연식 2012원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통엔진NA

공지

Part Description: 5.7L 롱 블록 (Long Block) Issue Description: 이 5.7L 롱 블록 어셈블리는 EGR 및 Non-EGR 적용 차량 모두에 호환됩니다. 이 롱 블록 어셈블리를 Non-EGR 적용 차량에 설치할 때는 EGR 블록오프 플레이트(53032739AA)를 별도로 주문해야 합니다. 단, 기존 엔진에서 EGR 블록오프 플레이트를 옮겨 사용하는 경우에는 예외입니다.

NHTSA · 제조사 공지10229181연식 2007자동 번역 · 원문: 영어자세히 보기 →
공지보통엔진NA

공지

Service - Four Piece Oil Pan Gasket All Cummins Equipped Vehicles ONLY - The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 Nm [21 ft. lbs.].

NHTSA · 제조사 공지10223854연식 2007원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통브레이크NA

공지

Adaptive Cruise Control Sensor 1) If you are replacing this part due to the cluster displaying Clean Radar Sensor in Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure

NHTSA · 제조사 공지10139956연식 2012원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통엔진NA

공지

Ram/dodge\jeep service campaign: See document search button for owner letter. The engine water pump on certain vehicles may leak coolant. Engine operation with a low coolant level could cause engine damage or low cabin heater output. Csc letter was rec'd. *pe

NHTSA · 제조사 공지10034071연식 2010원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통엔진NA

공지

Chrysler\dodge service campaign: See document search button for owner letter. An incorrect positive crankcase ventilation (pcv) valve may have been installed. An incorrect pcv valve can cause excessive exhaust emissions. Csc letter was received. *pe

NHTSA · 제조사 공지10028832연식 2009원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통전장NA

공지

Emissions recall g45--veci label - an incorrect vehicle emission control information (veci) label was installed on about ten thousand vehicles. The originally installed veci label does not display the correct spark plug information. *nj

NHTSA · 제조사 공지10023661연식 2007원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

Slight play in steering/stiff/choppy/bumpy ride. *nj

NHTSA · 제조사 공지10023393연식 2007원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

Steering angle sensor - not initialized/internal. *kb

NHTSA · 제조사 공지10021984연식 2007원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미기타NA

공지

LIFTER, Hydraulic Roller Deactivating (리프터, 유압 롤러 디액티베이팅) MDS 리프터는 디스커넥팅 핀이 정렬되어 있지 않더라도 교체하지 마십시오. 이는 정상적인 현상이며 결함이 아닙니다.

NHTSA · 제조사 공지10248517연식 2012자동 번역 · 원문: 영어자세히 보기 →
공지경미기타NA

공지

LIFTER, Hydraulic Roller Deactivating (유압 롤러 디액티베이팅 리프터) MDS 리프터는 분리 핀이 정렬되지 않았다는 이유만으로 교체하지 마십시오. 이는 정상적인 현상이며 결함이 아닙니다.

NHTSA · 제조사 공지10244356연식 2012자동 번역 · 원문: 영어자세히 보기 →
공지경미기타NA

공지

KEY, 마스터 WJ, KJ, TJ, PT 크루저에서 키/FOBIK를 교체할 때는 "AC" NIC 레벨 부품 번호를 사용하세요. "AB" NIC 레벨은 이 플랫폼들에 프로그래밍되지 않습니다. 다른 모든 플랫폼의 경우, "AB" NIC 레벨이 차량에 프로그래밍되지 않는다면, "AC" NIC 레벨 부품을 사용하고 부품 보증을 제출하세요.

NHTSA · 제조사 공지10229256연식 2005자동 번역 · 원문: 영어자세히 보기 →
공지경미변속기NA

공지

Customer Satisfaction Notification V51 Reprogram Powertrain Control Module

NHTSA · 제조사 공지10228020연식 2010원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미실내NA

공지

Warranty Bulletin D-20-17 (X85) Active Head Restraint - Select 2012-2013 Jeep Liberty (KK) and 2012 Dodge Nitro (KA) (Rev. A)

NHTSA · 제조사 공지10224064연식 2012원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미기타NA

공지

KEY, 마스터 WJ, KJ, TJ, PT 크루저에서 키/FOBIK를 교체할 때는 "AC" NIC 레벨 부품 번호를 사용하세요. "AB" NIC 레벨은 이 플랫폼들에 프로그래밍되지 않습니다. 다른 모든 플랫폼의 경우, "AB" NIC 레벨이 차량에 프로그래밍되지 않는다면, "AC" NIC 레벨 부품을 사용하고 부품 보증을 제출하세요.

NHTSA · 제조사 공지10221686연식 2005자동 번역 · 원문: 영어자세히 보기 →
공지경미변속기NA

공지

Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders

NHTSA · 제조사 공지10221150연식 2012원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미변속기NA

공지

변속기 키트(토크 컨버터 포함) 1. 모든 Promaster(VF) 3.6L/62TE 탑재 차량. 정비 중 변속기 브라켓과 변속기 케이스를 체결하는 볼트를 분리하는 경우, 해당 볼트(부품 번호 06511385A$)는 1회용입니다. 2015년 10/23 이전에 제작된 차량은 서비스 키트 PN 68461214AA가 필요하며, 이에는 변속기 아이솔레이터 PN 68264483AA, 어댑테이션 브라켓 68264479AA, 그리고 패스너 서비스 키트 PN 68329056AA가 포함됩니다. 2015년 10/23 이후에 제작되었거나 그 이후 제작된 차량은 패스너 서비스 키트 PN 68329056AA만 필요합니다. 2. 모든 3.6L/62TE 탑재 차량. 수리 중인 차량에 플렉스 플레이트 균열이나 펌프 부싱 불량이 있는 경우, 엔진 블록에 있는 두 개(2개)의 다월 핀이 모두 존재하는지 확인하십시오. 이 핀은 변속기 중심선을 크랭크축 중심선에 맞추는 역할을 합니다. 또한 변속기 케이스의 다월 정렬 구멍을 육안으로 점검하십시오. 구멍이 손상되었거나 늘어난 경우, 수리 중 엔진과 변속기를 올바르게 정렬할 수 없어 변속기/플렉스 플레이트 또는 펌프 부싱에 추가 손상이 생길 수 있으므로 변속기를 교체해야 합니다. 3. 모든 62TE 탑재 차량. 펌프 부싱이 긁히거나 손상되었고 다월 핀 정렬 구멍이 정상이라면, 변속기 전체를 교체하지 말고 펌프 어셈블리를 교체하십시오. 4. 모든 62TE 탑재 차량. 차량이 P0740 또는 P2764 고장 코드와 함께 떨림/미끄러짐 현상이 있는 경우, TCC 솔레노이드 작동을 점검하십시오. TCC 솔레노이드가 정상이라면 해당 코드는 토크 컨버터 고장을 나타내는 것이므로 토크 컨버터를 교체하십시오.

NHTSA · 제조사 공지10220840연식 2005자동 번역 · 원문: 영어자세히 보기 →
공지경미실내NA

공지

Warranty Bulletin D-20-21 (X91) Active Head Restraint - Select 2010 Dodge Journey (JC), Dodge Avenger/Chrysler Sebring (JS), Dodge Nitro (KA), Jeep Liberty (KK), Jeep Compass/Jeep Patriot (MK), Dodge Caliber (PM), Dodge Caravan (RT)

NHTSA · 제조사 공지10187658연식 2010원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미실내NA

공지

Warranty Bulletin D-20-22 (X92) Active Head Restraint - Select 2011 Dodge Journey (JC), Dodge Avenger/Chrysler 200 (JS), Dodge Nitro (KA), Jeep Liberty (KK), Jeep Compass/Jeep Patriot (MK), Dodge Caliber (PM), Dodge Caravan (RT), Dodge Durango (WD), Jeep Grand Cherokee (WK)

NHTSA · 제조사 공지10187659연식 2011원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미실내NA

공지

Warranty Bulletin D-20-17 (X85) Active Head Restraint - Select 2012-2013 Jeep Liberty (KK) and 2012 Dodge Nitro (KA) (Rev. B)

NHTSA · 제조사 공지10187663연식 2012원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미실내NA

공지

Warranty Bulletin D-20-21 (X91) Active Head Restraint - Select 2010 Dodge Journey (JC), Dodge Avenger/Chrysler Sebring (JS), Dodge Nitro (KA), Jeep Liberty (KK), Jeep Compass/Jeep Patriot (MK), Dodge Caliber (PM), Dodge Caravan/Chrysler Town & Country (RT) (Rev. A)

NHTSA · 제조사 공지10187667연식 2010원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미실내NA

공지

Active Head Restraint (AHR) Inadvertent Deployment - X92 Warranty Extension This bulletin involves inspecting the sled bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

NHTSA · 제조사 공지10187680연식 2011원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지경미실내NA

공지

Active Head Restraint (AHR) Inadvertent Deployment - X91 Warranty Extension This bulletin involves inspecting the sled bracket striker pin and possibly replacinga front seat AHR that has inadvertently deployed. Customers may comment on the following: The AHR is deployed on one or both front seats and will not reset.

NHTSA · 제조사 공지10187684연식 2010원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
이전 →

출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).