공지
플래시: 변속기 제어 모듈(TCM) 업데이트 고객은 다음 중 하나 이상에 대해 불만을 제기할 수 있습니다. 증상: 업시프트(1단 - 5단) 시 거칠거나 미끄러지는 느낌. 스로틀을 밟은 상태에서 킥다운 시 거칠거나 미끄러지는 느낌. 변속기 오일 냄새(탄 냄새). 이 서비스 속보는 최신 소프트웨어로 TCM을 재프로그래밍하는 작업을 포함합니다.
🔔 무료 계정을 만들고 Dodge 램 픽업 (모든 세대) 이메일 알림 받기
기술 서비스 공지(TSB)는 제조사가 알려진 문제에 대해 딜러에게 보내는 수리 지침입니다. 안전 리콜은 아니지만 결함을 확인해 주는 경우가 많습니다.
플래시: 변속기 제어 모듈(TCM) 업데이트 고객은 다음 중 하나 이상에 대해 불만을 제기할 수 있습니다. 증상: 업시프트(1단 - 5단) 시 거칠거나 미끄러지는 느낌. 스로틀을 밟은 상태에서 킥다운 시 거칠거나 미끄러지는 느낌. 변속기 오일 냄새(탄 냄새). 이 서비스 속보는 최신 소프트웨어로 TCM을 재프로그래밍하는 작업을 포함합니다.
Flash: Transmission Control Module (TCM) Updates Customers may comment on one or more of the following: SYMPTOM: **Harsh or slipping feeling during upshifts (1st - 5th). Harsh or slipping feeling during kickdown events under throttle. Transmission fluid odor (burnt smell).** During a 2 - 3 transmission upshift, the engine is hitting rev limit. Hesitation feel during a pedal tip in, while engine is warming up below 1 C (30 F) ambient temp. This bulletin involves reprogramming the TCM with the latest available software.
Flash: Transmission Control Module (TCM) Updates Customers may comment on one or more of the following: SYMPTOM: Harsh or slipping feeling during upshifts (1st - 5th). Harsh or slipping feeling during kickdown events under throttle. Transmission fluid odor (burnt smell). This bulletin involves reprogramming the TCM with the latest available software.
Flash: Transmission Control Module (TCM) Updates Customers may comment on one or more of the following: SYMPTOM: Harsh or slipping feeling during upshifts (1st - 5th). Harsh or slipping feeling during kickdown events under throttle. Transmission fluid odor (burnt smell).
**플래시: 파워트레인 제어 모듈(ECM/PCM) 업데이트** 고객은 고장 표시등(MIL)이 점등되는 현상을 겪게 되며, 차량에서 다음 진단 고장 코드(DTC) 중 하나 이상이 나타나거나 설정될 수 있습니다. **증상: 고객은 고장 표시등(MIL)이 점등되는 현상을 겪게 되며, 차량에서 다음 진단 고장 코드(DTC) 중 하나 이상이 나타나거나 설정될 수 있습니다: P0148-00 - 연료 공급 오류. P0850-00 - 파킹/중립 스위치 성능. P1191-00 - 흡기 온도 센서 합리성/성능. P032F - 내연기관 토크 부족. P208D-00 - 환원제 펌프 "A" 제어 회로 높음. P204A-00 - 환원제 압력 센서 회로. P20E9-00 - 환원제 압력 과다. P208B-00 - 환원제 펌프 1 제어 성능. P24B0-00 - 미립자 물질 센서 회로 낮음. P24B1-00 - 미립자 물질 센서 회로 높음. P2281-00 - MAF와 스로틀 바디 사이 공기 누출.** P0088-00 - 연료 레일 압력 과다 - 뱅크 1. P20CF-00 - 배기 후처리 연료 인젝터 "A" 열림 고착. P20DB-00 - 배기 후처리 연료 공급 제어 열림 고착. U0109-00 - 연료 펌프 제어 모듈과의 통신 손실. P1451-00 - 디젤 미립자 필터 시스템 성능. P2463-00 - 디젤 미립자 필터 막힘 - 그을음 축적 뱅크 1. P2459-00 - 디젤 미립자 필터 재생 빈도 과다. P0087-00 - 연료 레일 압력 낮음. P2540-00 - 저압 연료 시스템 센서 회로 범위/성능. P2543-00 - 저압 연료 시스템 센서 회로 간헐. P214D-00 - 미립자 필터 재생 중 SCR NOx 촉매 출구 온도 과다. P242B-00 - 배기가스 온도 센서 회로 성능 - 뱅크 1 센서 3. P24DA-00 - 미립자 물질 센서 배기 샘플 오류 뱅크 1. P20EE-00 - SCR NOx 촉매 효율 임계값 미만 - 뱅크 1 촉매 1. P226C-00 - 터보차저 부스트 제어 "A" 응답 지연. P229F-00 - NOx 센서 회로 범위/성능 - 뱅크 1. P0100-00 - 질량 또는 체적 공기 유량 센서 "A" 회로. P203F-00 - 환원제 수준 과소. 이 서비스 공지는 최신 소프트웨어로 엔진 제어 모듈(ECM/PCM)을 점검하고 필요 시 재프로그래밍하는 작업을 포함합니다.
Tire Pressure Monitoring System (TPMS) Red XX Displayed and/or Warning Indicator Illuminated Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): C1501-31 - Tire Pressure Sensor 1-No Signal. C1502-31 - Tire Pressure Sensor 2-No Signal. C1503-31 - Tire Pressure Sensor 3-No Signal. C1504-31 - Tire Pressure Sensor 4-No Signal. C1505-31 - Tire Pressure Sensor 5-No Signal. C1506-31 - Tire Pressure Sensor 6-No Signal. Customers may also comment on the following: TPMS displaying red "XX" for one or more sensors and/or the tire pressure warning light is on in the Instrument Panel Cluster (IPC). This bulletin involves scanning the TPMS sensors and replacing TPM sensor(s) found in the provided table.
Tire Pressure Monitoring System (TPMS) Red XX Displayed and/or Warning Indicator Illuminated Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): C1501-31 - Tire Pressure Sensor 1-No Signal. C1502-31 - Tire Pressure Sensor 2-No Signal. C1503-31 - Tire Pressure Sensor 3-No Signal. C1504-31 - Tire Pressure Sensor 4-No Signal. C1505-31 - Tire Pressure Sensor 5-No Signal. C1506-31 - Tire Pressure Sensor 6-No Signal. Customers may also comment on the following: TPMS displaying red "XX" for one or more sensors and/or the tire pressure warning light is on in the Instrument Panel Cluster (IPC). This bulletin involves scanning the TPMS sensors and replacing TPM sensor(s) found in the provided table.
Flash: Electric Power Steering (EPS) Module Updates Customers may experience the following: SYMPTOM: Battery drain due to the EPS system staying active after ignition off. This bulletin involves inspecting and possibly reprogramming the EPS module with the latest available software.
Flash: Electric Power Steering (EPS) Module Updates Customers may experience the following: SYMPTOM: Battery drain due to the EPS system staying active after ignition off. This bulletin involves inspecting and possibly reprogramming the EPS module with the latest available software.
Wrong Instrument Panel Cluster (IPC) Configuration Customers may comment on one or more the following: Oil pressure gauge and battery life gauges are blank or missing from the IPC Fig. 1. The Trailer Brake radial slider movement will not move past one bar and is inaccurate Fig. 2. NOTE: The Trailer Brake percentage does display correctly. This bulletin supersedes Technical Service Bulletin (TSB) 08-328-26, date of issue September 03, 2026,which should be removed from your files. All revisions are highlighted with **asterisks** and includean updated LOP. This Technical Service Bulletin (TSB) has also been released as a Rapid Service Update (RSU) 26-164, date of issue September 03, 2026. All applicable RSU VINs have been loaded. To verify this RSU service action is applicable to the vehicle, use VIP or perform a VIN search in DealerCONNECT/ServiceLibrary. All repairs are reimbursable within the provisions of warranty.
Wrong Instrument Panel Cluster (IPC) Configuration Customers may comment on one or more the following: SYMPTOM: Oil pressure gauge and battery life gauges are blank or missing from the IPC Fig. 1. The Trailer Brake radial slider movement will not move past one bar and is inaccurate Fig. 2. NOTE: The Trailer Brake percentage does display correctly. This bulletin involves performing a reconfigure and Proxi alignment on the IPC.
Brake Fluid Leak At The Brake System Control Module 2 (BSCM2) The customer may comment the following: SYMPTOM: Drops of brake fluid are on the ground. This bulletin involves tightening two BSCM2 brake line fittings.
Flash: Brake System Control Module (BSCM) Updates **Customers may experience one or more of the following: SYMPTOM: Warning message "Selec-Speed Unavailable" appears in the Instrument Panel Cluster (IPC) when trying to enable the Selec-Speed Control (SSC) function. NOTE: There will be no Diagnostic Trouble Codes (DTCs) and no driveability concerns with this symptom.** Anti-Lock Brake System (ABS), Electronic Stability Control (ESC) and 'Decel ACC' lights on in the IPC. Technicians may also find the following: DTC C121A-00 - Steering Angle Sensor Not Initialized - Is stored with no Malfunction Indicator Lamp (MIL). This bulletin involves reprogramming the BSCM with the latest available software.
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle exhibit/set SYMPTOM: one or more of the following Diagnostic Trouble Codes (DTCs): P219A - Bank 1 Air-Fuel Ratio Imbalance. P219B - Bank 2 Air-fuel Ratio Imbalance. P032F - Combustion Engine Producing Insufficient Torque. NOTE: This revision has an updated and more effective fix for DTC P219B than the prior version. Customers may experience one or more of the following: **Power Take Off (PTO) may cancel during engagement with high PTO loads.** Engine speed surging, unstable, hunting, or oscillating while coasting at low vehicle speeds. Stationary Idle PTO feature is not activating when the user configuration is selected to require parking brake be set (DD/DP Only). PTO not auto-resuming after hard-wired remote start (DD/DP Only). Driveline clunk or bump when coasting to a stop in cruise control mode. Engine idle undershoot or delayed response with power steering input. In addition, the following software enhancement(s) is available: Increase the duration that PTO related messages are displayed on the Instrument Panel Cluster (IPC) (DD/DP Only). This bulletin involves reprogramming the PCM with the latest available software.
Battery Pack Control Module (BPCM) Software Update Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) has been set: P1A29-00 - Cell Supervisory Circuit A Failure. U3017-00 - Control Module Timer/Clock Performance. Customers may also comment on one or more of the following: Vehicle in limp-home mode. Start/Stop feature will be disabled. This bulletin involves reprogramming the BPCM with the latest available software.
Not applicable to vehicles built for US market. Battery Pack Control Module (BPCM) Software Update Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation SYMPTOM: the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) has been set: **P1A29-00 - Cell Supervisory Circuit A Failure. U3017-00 - Control Module Timer/Clock Performance.** P0E55-00 - DC/DC Converter Current Sensor Circuit "A" Intermittent/erratic. Customers may also experience one or more of the following: **Vehicle in limp-home mode. Start/Stop feature will be disabled.** The 12-volt battery is not charging properly. The battery charge stays low or dies quickly, even after driving. The vehicle had to be towed due to battery not charging.
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0088-00 - Fuel Rail Pressure Too High - Bank 1. P208B-00 - Reductant Pump 1 Control Performance. P2540-00 - Low Pressure Fuel System Sensor Circuit Range/Performance. P0506-00 - Idle Control System RPM - Lower Than Expected. P20CF-00 - Exhaust Aftertreatment Fuel Injector "A" Stuck Open. P20DB-00 - Exhaust Aftertreatment Fuel Supply Control Stuck Open. P040B-00 - EGR Temperature Sensor 1 Circuit Performance. U0109-00 - Lost Communication With Fuel Pump Control Module. P1451-00 - Diesel Particulate Filter System Performance. P2463-00 - Diesel Particulate Filter Restriction - Soot Accumulation Bank 1. P1191-00 - Inlet Air Temperature Sensor Rational/Performance. P242F-00 - Diesel Particulate Filter Restriction - Ash Accumulation. P229F-00 - NOX Sensor Circuit Range/Performance - Bank 1. P2281-00 - Air Leak Between MAF And Throttle Body. P0087-00 - Fuel Rail Pressure Too Low. P2540-00 - Low Pressure Fuel System Sensor Circuit Range/Performance. P2543-00 - Low Pressure Fuel System Sensor Circuit Intermittent. P214D-00 - SCR NOx Catalyst Outlet Temperature Too High During Particulate Filter Regeneration. P242B-00 - Exhaust Gas Temperature Sensor Circuit Performance - Bank 1 Sensor 3. P24DA - Particulate Matter Sensor Exhaust Sample Error Bank 1. P20EE-00 - SCR NOx Catalyst Efficiency Below Threshold - Bank 1 Catalyst 1. P226C-00 - Turbocharger Boost Control "A" Slow Response. P2281-00 - Air Leak Between Maf And Throttle Body. P229F-00 - Nox Sensor Circuit Range/performance - Bank 1. P0100-00 - Mass Or Volume Air Flow Sensor "A" Circuit. P203F-00 - Reductant Level Too Low. P0423-00 - Heated Catalyst Efficiency Below Threshold Bank 1. P06B9-00 - Cylinder 1 Glow Plug Circuit Performance. This bulletin involves inspecting and possibly reprogramming the PCM with the latest available software.
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0088-00 - Fuel Rail Pressure Too High - Bank 1. P208B-00 - Reductant Pump 1 Control Performance. P2540-00 - Low Pressure Fuel System Sensor Circuit Range/Performance. P0506-00 - Idle Control System RPM - Lower Than Expected. P20CF-00 - Exhaust Aftertreatment Fuel Injector "A" Stuck Open. P20DB-00 - Exhaust Aftertreatment Fuel Supply Control Stuck Open. P040B-00 - EGR Temperature Sensor 1 Circuit Performance. U0109-00 - Lost Communication With Fuel Pump Control Module. P1451-00 - Diesel Particulate Filter System Performance. P2463-00 - Diesel Particulate Filter Restriction - Soot Accumulation Bank 1. P1191-00-Inlet Air Temperature Sensor Rational/Performance. P242F-00-Diesel Particulate Filter Restriction - Ash Accumulation. P229F-00 - NOX Sensor Circuit Range/Performance - Bank 1. P2281-00 - Air Leak Between MAF And Throttle Body. P0087-00 - Fuel Rail Pressure Too Low. P2540-00 - Low Pressure Fuel System Sensor Circuit Range/Performance. P2543-00 - Low Pressure Fuel System Sensor Circuit Intermittent. P214D-00 - SCR NOx Catalyst Outlet Temperature Too High During Particulate Filter Regeneration. P242B-00 - Exhaust Gas Temperature Sensor Circuit Performance - Bank 1 Sensor 3. P24DA - Particulate Matter Sensor Exhaust Sample Error Bank 1. P20EE-00 - SCR NOx Catalyst Efficiency Below Threshold - Bank 1 Catalyst 1. P226C-00 - Turbocharger Boost Control "A" Slow Response. P2281-00 - Air Leak Between Maf And Throttle Body. P229F-00 - Nox Sensor Circuit Range/performance - Bank 1. P0100-00 - Mass Or Volume Air Flow Sensor "A" Circuit. P203F-00 - Reductant Level Too Low. P0423-00 - Heated Catalyst Efficiency Below Threshold Bank 1. P06B9-00 - Cylinder 1 Glow Plug Circuit Performance. This bulletin involves inspecting and possibly reprogramming the PCM with the latest available software.
R1L/R1H Trailer Brake Setting In Radio Cannot Be Changed Customers may experience the following: SYMPTOM: Trailer brake setting in radio cannot be changed.
SA Market Only - Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): **P0088-00 - Fuel Rail Pressure Too High - Bank 1.** P0263-00 - Cylinder 1 Contribution/Balance. P0266-00 - Cylinder 2 Contribution/Balance. P0269-00 - Cylinder 3 Contribution/Balance. P0272-00 - Cylinder 4 Contribution/Balance. P0275-00 - Cylinder 5 Contribution/Balance. P0278-00 - Cylinder 6 Contribution/Balance. Customers may also comment one or more of the following: The engine runs rough and exhibits stumbling and shaking. Loss of power. NOTE: The perceived loss of power is due to an insufficient injector/torque response. This bulletin involves inspecting and possibly reprogramming the PCM with the latest available software.
Not applicable to vehicles built for US market. SA Market Only - Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): P0088-00 - Fuel Rail Pressure Too High - Bank 1. Customers may also comment on the following: Vehicle enters into limp home mode / exhibits a loss of power This bulletin involves inspecting and possibly reprogramming the PCM with the latest available software.
Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P219A - Bank 1 Air-Fuel Ratio Imbalance Bank 1. P219B - Bank 2 Air-fuel Ratio Imbalance. NOTE: This revision has an updated and more effective fix for DTC P219B than the prior version. Customers may also comment on one or more of the following: **Power Take-Off (PTO) may cancel during engagement with high PTO loads.** PTO not auto-resuming after hard-wired remote start (DD/DP Only). Engine speed surging, unstable, or oscillating while coasting at low vehicle speeds. Stationary Idle PTO feature is not activating when the user configuration is selected to require parking brake be set (DD/DP Only). In addition, the following software enhancement(s) is available: Increase the duration that Power Takeoff related messages are displayed on the Instrument Panel Cluster (IPC) (DD/DP Only) **This bulletin involves inspecting and possibly reprogramming the PCM with the latest available software.**
Oil Pan Leak Customers may experience the following: SYMPTOM: 'Low Oil Level' message on in the Instrument Panel Cluster (IPC). Oil Leak. This bulletin involves replacing the engine oil pan.
Oil Pan Leak Customers may experience the following: SYMPTOM: 'Low Oil Level' message on in the Instrument Panel Cluster (IPC). Oil Leak. This bulletin involves replacing the engine oil pan.
Flash: Brake System Control Module (BSCM) Update Customers may comment on the following: Anti-Lock Brake System (ABS), Electronic Stability Control (ESC), 'Decel ACC' lights on in Instrument Panel Cluster (IPC). Technicians may find the following: Diagnostic Trouble Code (DTC) "C121A-00 - Steering Angle Sensor Not Initialized" is stored with no Malfunction Indicator Lamp (MIL) illuminated This bulletin involves reprogramming the BSCM with the latest available software.
출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).