무료 열람 · 무료 계정으로 기여Anticars(2000)의 후속

Jeep Gladiator

2019– · 결함 10건 · 4개 시장

기술 서비스 공지(TSB)는 제조사가 알려진 문제에 대해 딜러에게 보내는 수리 지침입니다. 안전 리콜은 아니지만 결함을 확인해 주는 경우가 많습니다.

연식
공지보통서스펜션NA

공지

플래시: 구동계 제어 모듈(DTCM) 업데이트 고객은 고장 표시등(MIL) 점등과 차량이 다음 진단 문제 코드(DTC)를 표시/설정해야 합니다: C147B-92 - 전륜 차축 분리 센서 성능 또는 잘못된 작동. 고객은 다음 중 하나 이상에 대해 의견을 낼 수 있습니다: 4WD 시스템 경고등, 서비스 메시지 또는 깜빡이는 표시등이 계기판 클러스터(IPC)에 표시됩니다. 차량이 4WD를 제대로 작동시키지 않습니다. 이 안내는 최신 소프트웨어로 DTCM을 재프로그래밍하는 것을 포함합니다.

NHTSA · 제조사 공지11039910연식 2022자동 번역 · 원문: 영어자세히 보기 →
공지보통서스펜션NA

공지

Flash: Drivetrain Control Module (DTCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set the following Diagnostic Trouble Code (DTC): C147B-92 - Front Axle Disconnect Sensor Performance or Incorrect Operation. Customers may comment on one or more of the following: 4WD system warning lights, service messages, or flashing indicators are displayed in the Instrument Panel Cluster (IPC). The vehicle does not engage 4WD properly. This bulletin involves reprogramming the DTCM with the latest available software.

NHTSA · 제조사 공지11039909연식 2021원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

Flash: Drivetrain Control Module (DTCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set the following Diagnostic Trouble Code (DTC): C147B-92 - Front Axle Disconnect Sensor Performance or Incorrect Operation Customers may comment on one or more of the following: 4WD system warning lights, service messages, or flashing indicators are displayed in the Instrument Panel Cluster (IPC). The vehicle does not engage 4WD properly. This bulletin involves reprogramming the DTCM with the latest available software.

NHTSA · 제조사 공지11038550연식 2024원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

Flash: Drivetrain Control Module (DTCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set the following Diagnostic Trouble Code (DTC): C147B-92 - Front Axle Disconnect Sensor Performance or Incorrect Operation Customers may comment on one or more of the following: 4WD system warning lights, service messages, or flashing indicators are displayed in the Instrument Panel Cluster (IPC). The vehicle does not engage 4WD properly. This bulletin involves reprogramming the DTCM with the latest available software.

NHTSA · 제조사 공지11038548연식 2020원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

Flash: Drivetrain Control Module (DTCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set the following Diagnostic Trouble Code (DTC): C147B-92 - Front Axle Disconnect Sensor Performance or Incorrect Operation Customers may comment on one or more of the following: 4WD system warning lights, service messages, or flashing indicators are displayed in the Instrument Panel Cluster (IPC). The vehicle does not engage 4WD properly. This bulletin involves reprogramming the DTCM with the latest available software.

NHTSA · 제조사 공지11038549연식 2023원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

Flash: Drivetrain Control Module (DTCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set the following Diagnostic Trouble Code (DTC): C147B-92 - Front Axle Disconnect Sensor Performance or Incorrect Operation Customers may comment on one or more of the following: 4WD system warning lights, service messages, or flashing indicators are displayed in the Instrument Panel Cluster (IPC). The vehicle does not engage 4WD properly. This bulletin involves reprogramming the DTCM with the latest available software.

NHTSA · 제조사 공지11038522연식 2026원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

Flash: Drivetrain Control Module (DTCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set the following Diagnostic Trouble Code (DTC): C147B-92 - Front Axle Disconnect Sensor Performance or Incorrect Operation Customers may comment on one or more of the following: 4WD system warning lights, service messages, or flashing indicators are displayed in the Instrument Panel Cluster (IPC). The vehicle does not engage 4WD properly. This bulletin involves reprogramming the DTCM with the latest available software.

NHTSA · 제조사 공지11038521연식 2025원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

Flash: Drivetrain Control Module (DTCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set the following Diagnostic Trouble Code (DTC): C147B-92 - Front Axle Disconnect Sensor Performance or Incorrect Operation Customers may comment on one or more of the following: 4WD system warning lights, service messages, or flashing indicators are displayed in the Instrument Panel Cluster (IPC). The vehicle does not engage 4WD properly. This bulletin involves reprogramming the DTCM with the latest available software.

NHTSA · 제조사 공지11038513연식 2024원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

Flash: Drivetrain Control Module (DTCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set the following Diagnostic Trouble Code (DTC): C147B-92 - Front Axle Disconnect Sensor Performance or Incorrect Operation Customers may comment on one or more of the following: 4WD system warning lights, service messages, or flashing indicators are displayed in the Instrument Panel Cluster (IPC). The vehicle does not engage 4WD properly. This bulletin involves reprogramming the DTCM with the latest available software.

NHTSA · 제조사 공지11038512연식 2023원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

**플래시: 구동계 제어 모듈(DTCM) 업데이트** 고객이 고장 표시등(MIL) 점등을 경험해야 하며, 차량이 다음 고장 진단 코드(DTC)를 나타내거나 설정해야 합니다. 증상: C147B-92 - 프론트 액슬 디스커넥트 센서 성능 이상 또는 잘못된 작동 고객은 다음 중 하나 이상에 대해 문의할 수 있습니다: 계기판 클러스터(IPC)에 표시되는 4WD 시스템 경고등, 정비 메시지 또는 깜박이는 표시등. 차량이 4WD를 제대로 체결하지 않습니다. 이 기술 게시판은 최신 사용 가능 소프트웨어로 DTCM을 재프로그래밍하는 작업을 포함합니다.

NHTSA · 제조사 공지11038511연식 2020자동 번역 · 원문: 영어자세히 보기 →
공지보통서스펜션NA

공지

Flash: Drivetrain Control Module (DTCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set the following Diagnostic Trouble Code (DTC): C147B-92 - Front Axle Disconnect Sensor Performance or Incorrect Operation Customers may comment on one or more of the following: 4WD system warning lights, service messages, or flashing indicators are displayed in the Instrument Panel Cluster (IPC). The vehicle does not engage 4WD properly. This bulletin involves reprogramming the DTCM with the latest available software.

NHTSA · 제조사 공지11038485연식 2026원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

Flash: Drivetrain Control Module (DTCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set the following Diagnostic Trouble Code (DTC): C147B-92 - Front Axle Disconnect Sensor Performance or Incorrect Operation Customers may comment on one or more of the following: 4WD system warning lights, service messages, or flashing indicators are displayed in the Instrument Panel Cluster (IPC). The vehicle does not engage 4WD properly. This bulletin involves reprogramming the DTCM with the latest available software.

NHTSA · 제조사 공지11038484연식 2025원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통변속기NA

공지

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): **P0300 - Multiple Cylinder Misfire (Active or Stored status set during cold start catalyst heating). P0301 - Cylinder 1 Misfire (Active or Stored status set during cold start catalyst heating). P0302 - Cylinder 2 Misfire (Active or Stored status set during cold start catalyst heating). P0303 - Cylinder 3 Misfire (Active or Stored status set during cold start catalyst heating). P0304 - Cylinder 4 Misfire (Active or Stored status set during cold start catalyst heating). P0305-00 - Cylinder 5 Misfire (Active or Stored status set during cold start catalyst heating). P0306-00 - Cylinder 6 Misfire (Active or Stored status set during cold start catalyst heating).** P08A6 - Gear Lever Position Sensor System - Multiple Sensor Correlation. P152F - Engine Hood Switch 2 / Engine Hood Switch 1 Correlation. P1129 - Closed Loop Fueling Not Achieved - Bank 2 Upstream. P0152-02 - O2 Sensor 2/1 Circuit High. P0158-02 - O2 Sensor 2/2 Circuit High. P2504 - Charging System Output High. P0563 - Battery/System Voltage High. Customers may also comment on one or more of the following: **The vehicle has a rough idle. The engine has a miss. Noisy valvetrain. "Service Transmission" message in the Instrument Panel Cluster (IPC) due to clutch slip detection with the transfer case in neutral. NOTE: Some customers may experience wheel spin or traction loss. In these situations, the Powertrain Control Module (PCM) may interpret the event as excessive clutch slip. To prevent potential clutch damage, a message may be displayed in the Instrument Panel Cluster (IPC).** Clutch is overheating. Clutch is slipping on engagement. M18 FSAR-TSB-7161 -2- Inability to accelerate uphill. Vehicle does not start. Vehicle is stuck in limp-home mode

NHTSA · 제조사 공지11031450연식 2023원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

Flash: 컴포트 시트 및 휠(CSWM) 업데이트 고객님께서 다음과 같은 증상을 겪으실 수 있습니다. 증상: 열선 스티어링 휠이 충분히 뜨거워지지 않거나 작동하지 않습니다. 이 서비스 게시문은 CSWM을 최신 소프트웨어로 재프로그래밍하는 작업을 포함합니다.

NHTSA · 제조사 공지11030246연식 2026자동 번역 · 원문: 영어자세히 보기 →
공지보통서스펜션NA

공지

Flash: Comfort Seat And Wheel (CSWM) Updates The customer may experience the following: SYMPTOM: Heated Steering Wheel does not get hot enough or does not work. This bulletin involves reprogramming the CSWM with the latest available software.

NHTSA · 제조사 공지11030243연식 2023원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

Flash: Comfort Seat And Wheel (CSWM) Updates The customer may experience the following: SYMPTOM: Heated Steering Wheel does not get hot enough or does not work. This bulletin involves reprogramming the CSWM with the latest available software.

NHTSA · 제조사 공지11030245연식 2025원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

Flash: Comfort Seat And Wheel (CSWM) Updates The customer may experience the following: SYMPTOM: Heated Steering Wheel does not get hot enough or does not work. This bulletin involves reprogramming the CSWM with the latest available software.

NHTSA · 제조사 공지11030244연식 2024원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

Flash: Comfort Seat And Wheel (CSWM) Updates The customer may experience the following: SYMPTOM: Heated Steering Wheel does not get hot enough or does not work. This bulletin involves reprogramming the CSWM with the latest available software.

NHTSA · 제조사 공지11030221연식 2026원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

Flash: Comfort Seat And Wheel (CSWM) Updates The customer may experience the following: SYMPTOM: Heated Steering Wheel does not get hot enough or does not work. This bulletin involves reprogramming the CSWM with the latest available software.

NHTSA · 제조사 공지11030220연식 2025원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

플래시: 컴포트 시트 및 휠(CSWM) 업데이트 고객은 다음과 같은 증상을 경험할 수 있습니다. 증상: 열선 핸들이 충분히 뜨거워지지 않거나 작동하지 않음 이 서비스 公告(TSB)은 CSWM을 최신 소프트웨어로 다시 프로그래밍하는 작업을 포함합니다.

NHTSA · 제조사 공지11030219연식 2024자동 번역 · 원문: 영어자세히 보기 →
공지보통서스펜션NA

공지

Flash: Comfort Seat And Wheel (CSWM) Updates The customer may experience the following: SYMPTOM: Heated Steering Wheel does not get hot enough or does not work. This bulletin involves reprogramming the CSWM with the latest available software.

NHTSA · 제조사 공지11030218연식 2023원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통변속기NA

공지

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P08A6 Gear Lever Position Sensor System Multiple Sensor Correlation (Manual Transmission Only). P152F Engine Hood Switch 2 / Engine Hood Switch 1 Correlation. Customers may also comment on one or more of the following: "Service Transmission message on in the Instrument Panel Cluster (IPC) due to clutch slip detection (Manual Transmission Only). NOTE: Customers might experience wheel spin or slippage and the PCM could interpreted the wheel spin or slippage as slipping the clutch too much and to avoid clutch damage, the customer may see the message in the IPC. Vehicle is in limp home mode. Other software enhancements included: Engine oil pump in high pressure mode with cold engine oil to improve valvetrain component reliability. This bulletin involves reprogramming the PCM with the latest available software.

NHTSA · 제조사 공지11029675연식 2022원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통변속기NA

공지

**플래시: 파워트레인 컨트롤 모듈(PCM) 업데이트** 증상: 고객은 고장 표시등(MIL)이 점등되고 차량이 다음 진단 트러블 코드(DTC) 중 하나 이상을 표시하거나 설정하는 증상을 겪어야 합니다. P08A6 - 기어 레버 위치 센서 시스템 다중 센서 상관(수동 변속기 전용). P152F - 엔진 후드 스위치 2 / 엔진 후드 스위치 1 상관. P0300 - 다중 실린더 실화. P152E - 엔진 후드 스위치 2 회로 높음. P0032 - O2 센서 1/1 히터 회로 높음. P0038 - O2 센서 1/2 히터 회로 높음. P0052 - O2 센서 2/1 히터 회로 높음. P0058 - O2 센서 2/2 히터 회로 높음. P0132 - O2 센서 1/1 회로 높음. P0138 - O2 센서 1/2 회로 높음. P0152 - O2 센서 2/1 회로 높음. P0158 - O2 센서 2/2 회로 높음. P2100 - 전자식 스로틀 제어 모터 회로. 고객은 다음 중 하나 이상에 대해서도 불만을 제기할 수 있습니다. "클러치 슬립 감지로 인해 계기판 클러스터(IPC)에 변속기 정비 필요 메시지 표시(수동 변속기 전용)." 참고: 고객은 휠 스핀 또는 미끄러짐을 경험할 수 있으며, PCM은 이를 클러치가 과도하게 미끄러지는 것으로 해석할 수 있습니다. 클러치 손상을 방지하기 위해 고객은 IPC에서 이 메시지를 볼 수 있습니다. 차량은 림프 홈 모드에 있습니다. 공회전 시 엔진에서 스파크 노크/디토네이션 소음이 발생합니다. 기타 포함된 소프트웨어 개선 사항: 밸브트레인 부품의 신뢰성을 높이기 위해 냉간 엔진 오일 상태에서 엔진 오일 펌프를 고압 모드로 작동합니다. 이 기술 서비스 게시물은 최신 사용 가능한 소프트웨어로 PCM을 재프로그래밍하는 작업을 포함합니다.

NHTSA · 제조사 공지11029674연식 2021자동 번역 · 원문: 영어자세히 보기 →
공지보통변속기NA

공지

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): **P08A6 Gear Lever Position Sensor System Multiple Sensor Correlation (Manual Transmission Only). P152F Engine Hood Switch 2 / Engine Hood Switch 1 Correlation.** P0300 - Multiple Cylinder Misfire. P152E - Engine Hood Switch 2 Circuit High. P0032 - O2 Sensor 1/1 Heater Circuit High. P0038 - O2 Sensor 1/2 Heater Circuit High P0052 - O2 Sensor 2/1 Heater Circuit High P0058 - O2 Sensor 2/2 Heater Circuit High. P0132 - O2 Sensor 1/1 Circuit High. P0138 - O2 Sensor 1/2 Circuit High. P0152 - O2 Sensor 2/1 Circuit High. P0158 - O2 Sensor 2/2 Circuit High P2100 - Electronic Throttle Control Motor Circuit Customers may also comment on one or more of the following: **"Service Transmission message on in the Instrument Panel Cluster (IPC) due to clutch slip detection (Manual Transmission Only). NOTE: Customers might experience wheel spin or slippage and the PCM could interpreted the wheel spin or slippage as slipping the clutch too much and to avoid clutch damage, the customer may see the message in the IPC. Vehicle is in limp home mode.** Spark knock/detonation sound from the engine at idle. **Other software enhancements included: Engine oil pump in high pressure mode with cold engine oil to improve valvetrain component reliability.** This bulletin involves reprogramming the PCM with the latest available software.

NHTSA · 제조사 공지11028233연식 2021원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통변속기NA

공지

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P08A6 Gear Lever Position Sensor System Multiple Sensor Correlation (Manual Transmission Only). P152F Engine Hood Switch 2 / Engine Hood Switch 1 Correlation. Customers may also comment on one or more of the following: "Service Transmission message on in the Instrument Panel Cluster (IPC) due to clutch slip detection (Manual Transmission Only). NOTE: Customers might experience wheel spin or slippage and the PCM could interpreted the wheel spin or slippage as slipping the clutch too much and to avoid clutch damage, the customer may see the message in the IPC. Vehicle is in limp home mode. Other software enhancements included: Engine oil pump in high pressure mode with cold engine oil to improve valvetrain component reliability. This bulletin involves reprogramming the PCM with the latest available software.

NHTSA · 제조사 공지11028234연식 2022원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
이전 →

출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).