Some customers may experience the following symptoms of the wireless charger (Qi), even when the mobile device (smartphone etc.) is placed in the proper position on the wireless charger (Qi). It does not start charging. It stops charging with the indicator flashing in red after starting. It stops charging without any visible sign after starting. For CX-50, some customers may experience that despite placing the MagSafe-equipped iPhone at the center of the wireless charger, charging stops after about ten seconds. MagSafe-equipped iPhones use magnets to align the charger and the device. When charging MagSafe-equipped iPhones with a non-MagSafe compatible charger, improper alignment can cause the magnetic field required for charging to be disrupted by the magnets, significantly reducing charging efficiency.
NHTSA · 제조사 공지11012342연식 2021원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
MNAO has recently found an increase in non-returned cores within the United Radio (UR) exchange program. As a reminder, dealers have 90 days, after the order is placed, to return the exchanged part. Failure to return the exchanged part will result in a debit of the full component price. It is highly recommended to set a calendar reminder at the time of the order for no more than 60 days to ensure all orders are returned if repaired and if not repaired, contact the customer to cancel the order and return the unit.
NHTSA · 제조사 공지10243559연식 2021원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Some customers may experience the following symptoms of the wireless charger (Qi), even when the mobile device (smartphone etc.) is placed in the proper position on the wireless charger (Qi). - It does not start charging. - Soon after starting, it stops charging with the indicator flashing in red. - Soon after starting, it stops charging without any visible sign. These symptoms may be caused by improper control software of the wireless charger (Qi). To eliminate these concerns, the specification of the wireless charger (Qi) has been modified. NOTE: The modifications for the symptoms are different depending on the model.
NHTSA · 제조사 공지10243549연식 2021원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
When installing a navigation SD card, confirm that the card is unlocked. Also, Mazda Does Not Recommend swapping navigation system SD cards from one vehicle to another for testing. If swapped, the SD card that is installed into the other vehicle becomes linked to the VIN of that vehicle.
NHTSA · 제조사 공지10185967연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
If you experience issues with the current version of ID's such as missing tools or modules not showing after completing a network test, be advised that we are aware of these issues and are working to resolve them. As a counter measure, it is advised that you un-install ids and re-install version 103.00 and "do not update" until further notice.
NHTSA · 제조사 공지10185813연식 2017원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction) is stored in the FSC module and cannot be erased. This concern may be caused by an internal FSC failure. To eliminate this concern, the production process of the FSC has been modified.
NHTSA · 제조사 공지10154454연식 2018원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Some 2018 vehicles built after January 1, 2018 and equipped with Navigation may exhibit one of these concerns after the user inputs an address: A screen pops up that says "House number not found." After the user selects OK, the system finds the address or a nearby address.Instead of finding the correct address number the system adds a digit to the end of the number. Example: You enter 151 and the system comes back with 1510, 1511, 1515, 1516, etc. This only occurs with MAZDA CONNECT software version 59.00.532 or 59.00.540, which started being installed into vehicles in January 2018. The concern can be eliminated by installing MAZDA CONNECT software version 59.00.545 now available on MGSS.
NHTSA · 제조사 공지10136765연식 2018원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Some 2018 vehicles built after January 1, 2018 and equipped with Navigation may exhibit one of these concerns after the user inputs an address: A screen pops up that says "House number not found." After the user selects OK, the system finds the address or a nearby address.Instead of finding the correct address number the system adds a digit to the end of the number. Example: You enter 151 and the system comes back with 1510, 1511, 1515, 1516, etc.This only occurs with MAZDA CONNECT software version 59.00.540, which started being installed into vehicles in January 2018. The concern can be eliminated by installing MAZDA CONNECT software version 59.00.504.
NHTSA · 제조사 공지10134940연식 2018원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
When the LED headlight auto leveling system initialization has been performed using Mazda Modular Diagnostic System (M-MDS), the LED headlight warning light continues flashing and DTC C0061:54 is stored after unloading the vehicle from a trailer. DTC C0061:54 - [HEADLIGHT AUTO LEVELING SYSTEM] Acceleration sensor initial position learning not completed. This may be caused by a failure of the headlight auto leveling system initialization, which is performed while driving the vehicle.
NHTSA · 제조사 공지10134696연식 2018원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Some vehicles may experience the check engine light on with dtc p2610 and p2507 stored in memory after engine start and room fuse 15a (a) removed. P2610:00: Instrument cluster internal engine off timer performance problem p2507:00: Pcm battery voltage low input as a past malfunction, the customer will not notice it (no warning light illuminated), but the dtc may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed.
NHTSA · 제조사 공지10105501연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
When installing a navigation sd card, confirm that the card is unlocked. Also, mazda does not recommend swapping navigation system sd cards from one vehicle to another for testing. If swapped, the sd card that is installed into the other vehicle becomes linked to the vin of that vehicle.
NHTSA · 제조사 공지10091265연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
If you encounter a vehicle with dtc p0137 (circuit low input), check the rear harness at the red circled area in the following diagram. If an aftermarket alarm system is installed, the rear harness might have received damage from electro-tap connectors (a) or to the protector tube (b). This damage is not covered under warranty.
NHTSA · 제조사 공지10086522연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
If a customer has a vehicle communication related error on their app, perform the following: Disconnect the battery or unplug the module for at least 10 seconds.Reconnect the battery, wait 60 seconds and then have the customer try the app again.If the vehicle starts, order module 0000-8f-z80a.Note: There is a limited supply of the module at this time, therefore only use this part for this specific condition.Due to the limited supply, make sure you were shipped the a level part and not the original part before installing the part.Install the module and program it per mms programming instructions.Instruct the customer to update their account with the new module information, otherwise the mms will not work from the app.
NHTSA · 제조사 공지10086506연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Mazda connect software version 55.00.760 is now available on ms3. Use this version for all mazda connect updates, including open ssp98 vehicles. If ssp98 is closed, use tsb 09-024/16 to repair the vehicles.Click on "ids/infotainment", then "mazda connect updates" to download it. Update your usb drives according to the instructions in tsb 09-024/16.Also make sure to select "all files" for "save as type:". If left as "compressed (zipped) folder," the file will be saved as a ".Zip" no matter what you use as an extension.Attn: Technicians - be sure to document the software version installed on the repair order and inform your warranty administrator to provide the information in the repair text of the warranty claim.Mazda is working to make further improvements to the mazda connect infotainment system software, and may issue future software updates to improve system operation and performance. Software version updates can be found on ms3.
NHTSA · 제조사 공지10086424연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Some customers may complain about any the following infotainment system concerns: Reboot, Slow reboot in morning, Display frozen, Display blank. NOTE: Rear view monitor operation is normal, No DTC stored
NHTSA · 제조사 공지10203765연식 2021원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Some vehicles may experience a lack of power and the check engine light on with DTC P061B:00 stored in PCM memory under one of the following conditions (A or B). DTC P061B:00 - [PCM] Internal control module torque calculation performance problem. Due to an improper control logic of the PCM, the engine torque calculation error detection is too sensitive. To eliminate this concern, the PCM software has been modified.
NHTSA · 제조사 공지10190952연식 2019원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
After Pandora V7.0 was released on March 7th, the following problems have been found on vehicle with MAZDA CONNECT. Navigation voice guidance will skip and cut out losing many words.Pandora will suddenly disconnect and MAZDA CONNECT will revert to the previously used source. If you encounter a vehicle with these issues, DO NOT attempt any repairs on the vehicle. There is nothing wrong with the vehicle. This is an issue with the Pandora APP. Have the customer contact Pandora at pandora-support@pandora.com. NOTE: If the Pandora APP works on the customer's phone, they can stream Pandora using Bluetooth.
NHTSA · 제조사 공지10185963연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Some vehicles may experience the check engine light on with DTCs P2096:00, P2097:00 and/or P0524:00 that cannot be cleared by itself, and the check engine light stays on even if the detection condition has gone. P2096:00 - Air fuel too lean P2097:00 - Air fuel too rich P0524:00 - Engine oil pressure too low. This concern may be caused by improper PCM control logic. The PCM software has been modified to eliminate this concern.
NHTSA · 제조사 공지10180595연식 2019원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Some customers may complain about a high frequency noise (like a mosquito sound) while the active driving display is in the flip-up position. The noise may be coming from the capacitor inside the active driving display which vibrates according to the display control frequency. The circuit board resonates with it resulting in an audible noise. To eliminate this concern, the active driving display has been modified to use a higher frequency for the display control.
NHTSA · 제조사 공지10171849연식 2019원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
New IDs software version 102.00 and Update 102.01 is now available on MS3 IDs update 102.00 and 102.01 is now available on MS3 under the "IDs/Infotainment" tab.
NHTSA · 제조사 공지10186918연식 2017원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).