무료 열람 · 무료 계정으로 기여Anticars(2000)의 후속

Mazda CX-90

2023– · 1 세대 · 결함 9건 · 2개 시장
세대
모든 세대CX-902023–914428

기술 서비스 공지(TSB)는 제조사가 알려진 문제에 대해 딜러에게 보내는 수리 지침입니다. 안전 리콜은 아니지만 결함을 확인해 주는 경우가 많습니다.

공지보통전장NA

공지

DESCRIPTION Some customers may experience ATF seepage from the High-Voltage (HV) motor terminal area. If ATF seepage is confirmed at this location, one or more of the following conditions may occur: ATF is leaking from the HV cable. ATF is leaking from the inverter connection. This is caused by through-hole porosity generated during manufacturing of the intermediate terminal block (busbar), allowing oil to seep from the component. To eliminate this concern, an Impregnation treatment (a sealing process in which resin, oil, or other liquids are infused into minute internal voids in the material, such as porosity, pinholes, or cracks) is applied to the aluminum plate portion of the busbar. REPAIR PROCEDURE 1. Verify the customer concern. 2. Replace the busbar with a new one.

NHTSA · 제조사 공지11035601연식 2024원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통전장NA

공지

This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red text. SA-037/26 05/28/26 DESCRIPTION Replacement battery packs for High Voltage systems are supplied with an additional label that matches the one attached to the service battery pack (refer to the sample High Voltage Battery Label image for reference). When replacing the battery pack in a 2026 or later model that has a similar label at the base of the left B-pillar, replace the label with the new one included in the service parts battery pack. REPAIR PROCEDURE Label Application: When replacing a High Voltage Battery: refer to the Label Application Process included in the "HIGH VOLTAGE BATTERY REMOVAL/INSTALLATION" or "M Hybrid Boost BATTERY REMOVAL/INSTALLATION" procedures in the Workshop Manual for the applicable models.

NHTSA · 제조사 공지11034440연식 2026원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통전장NA

공지

This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red text. SA-049/25 10/16/2025 DESCRIPTION Replacement battery packs for High Voltage systems are supplied with an additional label that matches the one attached to the service battery pack (refer to the sample High Voltage Battery Label image for reference). When replacing the battery pack in a 2026 or later model that has a similar label at the base of the left B-pillar, replace the label with the new one included in the service parts battery pack. REPAIR PROCEDURE Label Application: When replacing a High Voltage Battery: refer to the Label Application Process included in the "HIGH VOLTAGE BATTERY REMOVAL/INSTALLATION" or "M Hybrid Boost BATTERY REMOVAL/INSTALLATION" procedures in the Workshop Manual for the applicable models. In addition to the procedures outlined in the Workshop Manual, please follow these additional steps when removing an existing label to help simplify the application of the new one:

NHTSA · 제조사 공지11033443연식 2026원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

Some vehicles may exhibit a creaking or squeaking noise from the lower control arm at the front suspension when traveling over a bump while turning at low-speed. A stick-slip phenomenon may occur between the stopper rubber (2) and the bracket (3) in the front lower arm (rear) (1). To eliminate this concern: Grease has been applied to the stopper rubber. Dust covers have been installed to the lower arm. The mounting hole size of the lower arm bracket has been modified.

NHTSA · 제조사 공지11033112연식 2024원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통차체NA

공지

Some vehicles may exhibit an interference between the front (1) and the rear door bright window glass molding (2) due to the bright window glass molding shifting backward when opening/closing the front door. This is caused by an inappropriate position of the positioning tab on the front door glass run-channel. To eliminate this concern, double-sided tape has been added to the front door glass run-channel, and the shape of the rear end of the front door glass run-channel has been modified to prevent the bright window glass molding from shifting. Customers having this concern should have their vehicle repaired using the following repair procedure. REPAIR PROCEDURE 1. Verify the customer concern. 2. Replace the front glass run-channel(s) with a modified one(s) according to the instructions in MGSS (FRONT DOOR GLASS RUN-CHANNEL REMOVAL/INSTALLATION). NOTE: Repair only the side with the issue. ATTENTION: Removing the front beltline moldings is unnecessary for this repair procedure when replacing the front door glass run-channel. 3. Verify the repair.

NHTSA · 제조사 공지11030601연식 2024원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통전장NA

공지

On some vehicles, an engine oil leak from the rear of the engine at the turbocharger drain back tube could be be confused as an oil leak from behind the bell housing. The bolt holes for the drain back tube to the block are drilled through to the inside of the engine and thread sealer was not properly applied to the bolts threads, causing oil to leak past the threads. NOTE: The WSM was updated to show these bolts are a to be replaced if removed. New bolts will have thread sealer already applied.

NHTSA · 제조사 공지11029491연식 2025원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통전장NA

공지

This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red. 09-019/25 04/15/25 Some vehicles equipped with the Adaptive Front lighting System (AFS) may exhibit the exterior light warning light/exterior light warning indication on while driving or when the ignition is turned on and DTC B10A3:86 (Error signal received from swivel actuator (LH)) stored in memory. NOTE: The combination light with AFS can be distinguished if it is equipped with the parking light/daytime running light (DRL) that illuminates while the ignition is turned on. This may be caused by the AFS Control Module detecting a false headlight malfunction. This concern will likely occur when the light returns to the center position after swiveling. To eliminate this concern, the control software of the AFS control module has been further modified.

NHTSA · 제조사 공지11029238연식 2025원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통기타NA

공지

Some customers may complain that the A/C is not cold enough. Upon inspection, a refrigerant leak (1) from the A/C hose (LO) (2) is confirmed. This may be caused by foreign material present on the block side at the A/C hose (LO) connection point. To eliminate this concern, an inspection process for foreign materials was added to the parts manufacturing process as a temporary measure. A permanent measure is under study.

NHTSA · 제조사 공지11026096연식 2025원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통전장NA

공지

SSPD9 Adding coverage for Towing Subject: Notification of Warranty Extension Program - Special Service Program (SSP) D9 2024 CX-90 and 2025 CX-70, SKYACTIV-G 2.5 PHEV Water Heater Malfunction Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) to extend the warranty coverage for a specific repair of the water heater concern on certain MY2024 CX-90 PHEV and MY2025 CX-70 PHEV vehicles that are equipped with the suspected water heater. The warranty coverage for an applicable repair has been extended to 8 years (96 months) from the original warranty start date, with no mileage limitation. Concern Outline: On certain subject vehicles, while warming up the cabin after starting the vehicle in EV mode, the nichrome wire in the water heater may break or a decrease in insulation resistance may be detected, causing the concerns described below: 1) The heater does not work properly. 2) The hybrid system warning light may turn on and the DTC P0AA6:00 may be stored in memory. - P0AA6:00 High voltage insulation malfunction: Decrease in vehicle insulation resistance. This is a warranty extension for the specified repair only. Inspection and replacement of non-failed parts will not be eligible for reimbursement under this SSP to the dealer or customer. This program extends the warranty period for actual failures due to defects in workmanship or materials in accordance with the Mazda Warranty Policy and Procedures. If a customer arrives at your dealership with the concern described, please repair the vehicle under this Special Service Program. SSPD9 Water Heater Malfunction WARRANTY EXTENSION For certain 2024 CX-90 PHEV and 2025 CX-70 PHEV vehicles that are equipped with the suspected water heater, the warranty coverage for an applicable repair of the water heater has been extended to 8 years (96 months) from the original warranty start date, with no mileage limitation. CONDITION OF CONCERN While warning up the cabin using the water heater after starting the vehicle in EV mode, the nichrome wire in the water heater may break or a decrease in insulation resistance may be detected, causing the concerns described below: Heater performance may become poor: 1. The hybrid system warning light may turn on and the DTC P0AA6:00 may be stored. 2. P0AA6:00 High voltage insulation malfunction: Decrease in vehicle insulation resistance OWNER NOTIFICATION Mazda will notify all U.S. owners of the subject vehicles by first class mail no later than September 1, 2025. Owners will be advised that they do not need to bring their vehicle to a dealer if it does not exhibit the affected conditions. Owners will also be advised that any previous repair on the water heater due to concerns related to this SSP will be eligible for reimbursement if the repair was performed at the owners expense. Please refer the customer to the Owner Letter for reimbursement instructions. NO COVERAGE FOR BRANDED AND OTHER LIMITATIONS - EXCLUDED COVERAGE Per Warranty policy 3.26 all limitations apply to this Warranty Extension. There is no coverage for total loss/insurance/salvage or rebuilt titles (W1). If you are unsure about the policy please contact the Warranty Department. REPAIR PROCEDURE If you receive customer complaints about the check engine light ON with P0AA6:00 with any of the symptoms mentioned above, verify the concerns and perform appropriate repair according to the Service Information Technical Service Bulletin (TSB) No. 07-006/24. Note: Please always refer to the latest version of TSB.

NHTSA · 제조사 공지11023704연식 2024–2025원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통엔진NA

공지

Regarding previous Service Alert "Fuel Gauge Inaccurate / Distance To Empty (DTE) Erratic / Engine No Start" issue. This SA has been replaced by 7825I - SAFETY AND EMISSIONS RECALL - 2024-2025 CX-90 AND 2025 CX-70 - VEHICLE MAY STALL DUE TO INCORRECT FUEL LEVEL.

NHTSA · 제조사 공지11023699연식 2025원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통전장NA

공지

SSPD9 August 25, 2025 Adding coverage for Towing Subject: Notification of Warranty Extension Program - Special Service Program (SSP) D9 2024 CX-90 and 2025 CX-70, SKYACTIV-G 2.5 PHEV Water Heater Malfunction Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) to extend the warranty coverage for a specific repair of the water heater concern on certain MY2024 CX-90 PHEV and MY2025 CX-70 PHEV vehicles that are equipped with the suspected water heater. The warranty coverage for an applicable repair has been extended to 8 years (96 months) from the original warranty start date, with no mileage limitation. Concern Outline: On certain subject vehicles, while warming up the cabin after starting the vehicle in EV mode, the nichrome wire in the water heater may break or a decrease in insulation resistance may be detected, causing the concerns described below: 1) The heater does not work properly. 2) The hybrid system warning light may turn on and the DTC P0AA6:00 may be stored in memory. - P0AA6:00 High voltage insulation malfunction: Decrease in vehicle insulation resistance. This is a warranty extension for the specified repair only. Inspection and replacement of non-failed parts will not be eligible for reimbursement under this SSP to the dealer or customer. This program extends the warranty period for actual failures due to defects in workmanship or materials in accordance with the Mazda Warranty Policy and Procedures. If a customer arrives at your dealership with the concern described, please repair the vehicle under this Special Service Program. SSPD9 Water Heater Malfunction WARRANTY EXTENSION For certain 2024 CX-90 PHEV and 2025 CX-70 PHEV vehicles that are equipped with the suspected water heater, the warranty coverage for an applicable repair of the water heater has been extended to 8 years (96 months) from the original warranty start date, with no mileage limitation. CONDITION OF CONCERN While warning up the cabin using the water heater after starting the vehicle in EV mode, the nichrome wire in the water heater may break or a decrease in insulation resistance may be detected, causing the concerns described below: Heater performance may become poor: 1. The hybrid system warning light may turn on and the DTC P0AA6:00 may be stored. 2. P0AA6:00 High voltage insulation malfunction: Decrease in vehicle insulation resistance OWNER NOTIFICATION Mazda will notify all U.S. owners of the subject vehicles by first class mail no later than September 1, 2025. Owners will be advised that they do not need to bring their vehicle to a dealer if it does not exhibit the affected conditions. Owners will also be advised that any previous repair on the water heater due to concerns related to this SSP will be eligible for reimbursement if the repair was performed at the owners expense. Please refer the customer to the Owner Letter for reimbursement instructions. NO COVERAGE FOR BRANDED AND OTHER LIMITATIONS - EXCLUDED COVERAGE Per Warranty policy 3.26 all limitations apply to this Warranty Extension. There is no coverage for total loss/insurance/salvage or rebuilt titles (W1). If you are unsure about the policy please contact the Warranty Department. REPAIR PROCEDURE If you receive customer complaints about the check engine light ON with P0AA6:00 with any of the symptoms mentioned above, verify the concerns and perform appropriate repair according to the Service Information Technical Service Bulletin (TSB) No. 07-006/24. Note: Please always refer to the latest version of TSB.

NHTSA · 제조사 공지11022773연식 2024–2025원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통전장NA

공지

Subject: Notification of Warranty Extension Program - Special Service Program (SSP) D9 2024 CX-90 and 2025 CX-70, SKYACTIV-G 2.5 PHEV Water Heater Malfunction Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) to extend the warranty coverage for a specific repair of the water heater concern on certain MY2024 CX-90 PHEV and MY2025 CX-70 PHEV vehicles that are equipped with the suspected water heater. The warranty coverage for an applicable repair has been extended to 8 years (96 months) from the original warranty start date, with no mileage limitation. Concern Outline: On certain subject vehicles, while warming up the cabin after starting the vehicle in EV mode, the nichrome wire in the water heater may break or a decrease in insulation resistance may be detected, causing the concerns described below: 1) The heater does not work properly. 2) The hybrid system warning light may turn on and the DTC P0AA6:00 may be stored in memory. - P0AA6:00 High voltage insulation malfunction: Decrease in vehicle insulation resistance. This is a warranty extension for the specified repair only. Inspection and replacement of non-failed parts will not be eligible for reimbursement under this SSP to the dealer or customer. This program extends the warranty period for actual failures due to defects in workmanship or materials in accordance with the Mazda Warranty Policy and Procedures. If a customer arrives at your dealership with the concern described, please repair the vehicle under this Special Service Program. SSPD9 Water Heater Malfunction WARRANTY EXTENSION For certain 2024 CX-90 PHEV and 2025 CX-70 PHEV vehicles that are equipped with the suspected water heater, the warranty coverage for an applicable repair of the water heater has been extended to 8 years (96 months) from the original warranty start date, with no mileage limitation. CONDITION OF CONCERN While warning up the cabin using the water heater after starting the vehicle in EV mode, the nichrome wire in the water heater may break or a decrease in insulation resistance may be detected, causing the concerns described below: Heater performance may become poor: 1. The hybrid system warning light may turn on and the DTC P0AA6:00 may be stored. 2. P0AA6:00 High voltage insulation malfunction: Decrease in vehicle insulation resistance OWNER NOTIFICATION Mazda will notify all U.S. owners of the subject vehicles by first class mail no later than September 1, 2025. Owners will be advised that they do not need to bring their vehicle to a dealer if it does not exhibit the affected conditions. Owners will also be advised that any previous repair on the water heater due to concerns related to this SSP will be eligible for reimbursement if the repair was performed at the owners expense. Please refer the customer to the Owner Letter for reimbursement instructions. NO COVERAGE FOR BRANDED AND OTHER LIMITATIONS - EXCLUDED COVERAGE Per Warranty policy 3.26 all limitations apply to this Warranty Extension. There is no coverage for total loss/insurance/salvage or rebuilt titles (W1). If you are unsure about the policy please contact the Warranty Department. REPAIR PROCEDURE If you receive customer complaints about the check engine light ON with P0AA6:00 with any of the symptoms mentioned above, verify the concerns and perform appropriate repair according to the Service Information Technical Service Bulletin (TSB) No. 07-006/24. Note: Please always refer to the latest version of TSB.

NHTSA · 제조사 공지11022770연식 2024–2025원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통전장NA

공지

Subject: Notification of Warranty Extension Program - Special Service Program (SSP) D9 2024 CX-90 and 2025 CX-70, SKYACTIV-G 2.5 PHEV Water Heater Malfunction Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) to extend the warranty coverage for a specific repair of the water heater concern on certain MY2024 CX-90 PHEV and MY2025 CX-70 PHEV vehicles that are equipped with the suspected water heater. The warranty coverage for an applicable repair has been extended to 8 years (96 months) from the original warranty start date, with no mileage limitation. Concern Outline: On certain subject vehicles, while warming up the cabin after starting the vehicle in EV mode, the nichrome wire in the water heater may break or a decrease in insulation resistance may be detected, causing the concerns described below: 1) The heater does not work properly. 2) The hybrid system warning light may turn on and the DTC P0AA6:00 may be stored in memory. - P0AA6:00 High voltage insulation malfunction: Decrease in vehicle insulation resistance. This is a warranty extension for the specified repair only. Inspection and replacement of non-failed parts will not be eligible for reimbursement under this SSP to the dealer or customer. This program extends the warranty period for actual failures due to defects in workmanship or materials in accordance with the Mazda Warranty Policy and Procedures. If a customer arrives at your dealership with the concern described, please repair the vehicle under this Special Service Program.

NHTSA · 제조사 공지11022765연식 2024–2025원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통전장NA

공지

Some vehicles may exhibit a loud vibration noise when the electric A/C compressor is operating. Due to processing variation of the counter-balance bushing (a weight to balance eccentric rotation) installed in the electric compressor, some of the bushing strongly interferes with the shaft, resulting in the humming noise. To eliminate this concern, the machining accuracy of the counter-balance bushing has been improved.

NHTSA · 제조사 공지11019986연식 2024원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통전장NA

공지

7325C - EMISSION RECALL - 2024-2025 CX-90 AND 2025 CX-70 PHEV ONLY - HYBRID SYSTEM WARNING LIGHT MAY TURN ON. Mazda Motor Corporation has decided to conduct an Emission Recall on certain 2024-2025 CX-90 and 2025 CX-70 PHEV vehicles. Please see the description, model, year, and VIN range below for all vehicles in this campaign. There are 38,812 vehicles affected by this concern in the U.S. and U.S. Territories. Vehicles produced and sold by Mazda Canada Inc. are also included in this campaign and should be repaired if presented to your dealership following Mazda Warranty policy 3.30.STOP DELIVERY OF AFFECTED VEHICLES: MAZDA SALES AND SERVICE TEAMS - ACTION ITEM: There are approximately 5,197 vehicles in stock at U.S. Mazda dealers which must be repaired prior to delivery. All Mazda dealers must quarantine any affected new, used or CPO in-stock vehicles until the repair is completed. The affected dealer inventory list was provided to each District Service Manager with the notification of this dealer email. Once completed, the car can be delivered, and the Warranty claim can be submitted later without penalty since the car has been repaired. To All Mazda Dealers: Failure to properly perform any recall repair is a direct violation of Paragraph 14(F) of the Dealer Agreement and can cause one or more of the following: Mechanical breakdown or failure, crash or injury, Dealership penalties/fines by Mazda and CARB/EPA, increased liability risk for the dealership, Missed Recall penalties, loss of customer trust and a poor Customer Experience. Concern Outline: All vehicles can be repaired immediately upon receipt of this Mazda Dealer announcement by following the repair and warranty claiming procedures housed in Mazda Global Service Support (MGSS). On certain subject vehicles, during normal driving, a temporary decrease in insulation resistance may be detected, which could be mistakenly judged as an electric leakage, causing the hybrid system warning light to turn on and the leakage detection message to be displayed. The DTC P0AA6:00 may be stored in memory. In such a condition, once the vehicle power is switched off, it may become impossible to restart the vehicle due to fail-safe mode activation. Repair Outline: Reprogram the PCM with the Mazda Modular Diagnostic System (M-MDS), using Mazda Diagnostic and Repair Software (MDARS). The DTC code that may appear is P0AA6:00 - High voltage insulation malfunction: Decrease in vehicle insulation resistance. The software update will re-calibrate electrical leakage detection criteria and allow vehicle re-start. Legitimate electrical leakage faults can still be detected and store DTC P0AA6:00. If DTC P0AA6:00 - High voltage insulation malfunction: Decrease in vehicle insulation resistance is still present after repair of the 7325C Recall, please diagnose the issue using the Workshop Manual or search for a current Technical Service Bulletin.

NHTSA · 제조사 공지11019173연식 2025원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

Some vehicles may exhibit a creaking or squeaking noise from the lower control arm at the front suspension when traveling over a bump while turning at low-speed. A stick-slip phenomenon may occur between the stopper rubber (2) and the bracket (3) in the front lower arm (rear) (1). To eliminate this concern: Grease has been applied to the stopper rubber. Dust covers have been installed to the lower arm. The mounting hole size of the lower arm bracket has been modified.

NHTSA · 제조사 공지11019085연식 2024원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통전장NA

공지

7325C - EMISSION RECALL - 2024-2025 CX-90 AND 2025 CX-70 PHEV ONLY - HYBRID SYSTEM WARNING LIGHT MAY TURN ON. Mazda Motor Corporation has decided to conduct an Emission Recall on certain 2024-2025 CX-90 and 2025 CX-70 PHEV vehicles. Please see the description, model, year, and VIN range below for all vehicles in this campaign. There are 38,812 vehicles affected by this concern in the U.S. and U.S. Territories. Vehicles produced and sold by Mazda Canada Inc. are also included in this campaign and should be repaired if presented to your dealership following Mazda Warranty policy 3.30.STOP DELIVERY OF AFFECTED VEHICLES: MAZDA SALES AND SERVICE TEAMS - ACTION ITEM: There are approximately 5,197 vehicles in stock at U.S. Mazda dealers which must be repaired prior to delivery. All Mazda dealers must quarantine any affected new, used or CPO in-stock vehicles until the repair is completed. The affected dealer inventory list was provided to each District Service Manager with the notification of this dealer email. Once completed, the car can be delivered, and the Warranty claim can be submitted later without penalty since the car has been repaired. To All Mazda Dealers: Failure to properly perform any recall repair is a direct violation of Paragraph 14(F) of the Dealer Agreement and can cause one or more of the following: Mechanical breakdown or failure, crash or injury, Dealership penalties/fines by Mazda and CARB/EPA, increased liability risk for the dealership, Missed Recall penalties, loss of customer trust and a poor Customer Experience. Concern Outline: All vehicles can be repaired immediately upon receipt of this Mazda Dealer announcement by following the repair and warranty claiming procedures housed in Mazda Global Service Support (MGSS). On certain subject vehicles, during normal driving, a temporary decrease in insulation resistance may be detected, which could be mistakenly judged as an electric leakage, causing the hybrid system warning light to turn on and the leakage detection message to be displayed. The DTC P0AA6:00 may be stored in memory. In such a condition, once the vehicle power is switched off, it may become impossible to restart the vehicle due to fail-safe mode activation. Repair Outline: Reprogram the PCM with the Mazda Modular Diagnostic System (M-MDS), using Mazda Diagnostic and Repair Software (MDARS). The DTC code that may appear is P0AA6:00 - High voltage insulation malfunction: Decrease in vehicle insulation resistance. The software update will re-calibrate electrical leakage detection criteria and allow vehicle re-start. Legitimate electrical leakage faults can still be detected and store DTC P0AA6:00. If DTC P0AA6:00 - High voltage insulation malfunction: Decrease in vehicle insulation resistance is still present after repair of the 7325C Recall, please diagnose the issue using the Workshop Manual or search for a current Technical Service Bulletin.

NHTSA · 제조사 공지11017711연식 2025원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통전장NA

공지

Some vehicles equipped with the Adaptive Front lighting System (AFS) may exhibit the exterior light warning light/exterior light warning indication on while driving or when the ignition is turned on and DTC B10A3:86 (Error signal received from swivel actuator (LH)) stored in memory. NOTE: The combination light with AFS can be distinguished if it is equipped with the parking light/daytime running light (DRL) that illuminates while the ignition is turned on. This may be caused by the AFS Control Module detecting a false headlight malfunction. This concern will likely occur when the light returns to the center position after swiveling.To eliminate this concern, the control software of the AFS control module has been further modified. Customers having this concern should have their vehicle repaired using the following repair procedure.

NHTSA · 제조사 공지11017483연식 2025원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통전장NA

공지

7325C - EMISSION RECALL - 2024-2025 CX-90 AND 2025 CX-70 PHEV ONLY - HYBRID SYSTEM WARNING LIGHT MAY TURN ON. Mazda Motor Corporation has decided to conduct an Emission Recall on certain 2024-2025 CX-90 and 2025 CX-70 PHEV vehicles. Please see the description, model, year, and VIN range below for all vehicles in this campaign. There are 38,812 vehicles affected by this concern in the U.S. and U.S. Territories. Vehicles produced and sold by Mazda Canada Inc. are also included in this campaign and should be repaired if presented to your dealership following Mazda Warranty policy 3.30. STOP DELIVERY OF AFFECTED VEHICLES: MAZDA SALES AND SERVICE TEAMS - ACTION ITEM: There are approximately 5,197 vehicles in stock at U.S. Mazda dealers which must be repaired prior to delivery. All Mazda dealers must quarantine any affected new, used or CPO in-stock vehicles until the repair is completed. The affected dealer inventory list was provided to each District Service Manager with the notification of this dealer email. Once completed, the car can be delivered, and the Warranty claim can be submitted later without penalty since the car has been repaired.To All Mazda Dealers: Failure to properly perform any recall repair is a direct violation of Paragraph 14(F) of the Dealer Agreement and can cause one or more of the following: Mechanical breakdown or failure, crash or injury, Dealership penalties/fines by Mazda and CARB/EPA, increased liability risk for the dealership, Missed Recall penalties, loss of customer trust and a poor Customer Experience. Concern Outline: All vehicles can be repaired immediately upon receipt of this Mazda Dealer announcement by following the repair and warranty claiming procedures housed in Mazda Global Service Support (MGSS). On certain subject vehicles, during normal driving, a temporary decrease in insulation resistance may be detected, which could be mistakenly judged as an electric leakage, causing the hybrid system warning light to turn on and the leakage detection message to be displayed. The DTC P0AA6:00 may be stored in memory. In such a condition, once the vehicle power is switched off, it may become impossible to restart the vehicle due to fail-safe mode activation. Repair Outline: Reprogram the PCM with the Mazda Modular Diagnostic System (M-MDS), using Mazda Diagnostic and Repair Software (MDARS). The DTC code that may appear is P0AA6:00 - High voltage insulation malfunction: Decrease in vehicle insulation resistance. The software update will re-calibrate electrical leakage detection criteria and allow vehicle re-start. Legitimate electrical leakage faults can still be detected and store DTC P0AA6:00. If DTC P0AA6:00 - High voltage insulation malfunction: Decrease in vehicle insulation resistance is still present after repair of the 7325C Recall, please diagnose the issue using the Workshop Manual or search for a current Technical Service Bulletin.

NHTSA · 제조사 공지11016386연식 2025원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통전장NA

공지

7325C - EMISSION RECALL - 2024-2025 CX-90 AND 2025 CX-70 PHEV ONLY - HYBRID SYSTEM WARNING LIGHT MAY TURN ON. Mazda Motor Corporation has decided to conduct an Emission Recall on certain 2024-2025 CX-90 and 2025 CX-70 PHEV vehicles. Please see the description, model, year, and VIN range below for all vehicles in this campaign. There are 38,812 vehicles affected by this concern in the U.S. and U.S. Territories. Vehicles produced and sold by Mazda Canada Inc. are also included in this campaign and should be repaired if presented to your dealership following Mazda Warranty policy 3.30. STOP DELIVERY OF AFFECTED VEHICLES: MAZDA SALES AND SERVICE TEAMS - ACTION ITEM: There are approximately 5,197 vehicles in stock at U.S. Mazda dealers which must be repaired prior to delivery. All Mazda dealers must quarantine any affected new, used or CPO in-stock vehicles until the repair is completed. The affected dealer inventory list was provided to each District Service Manager with the notification of this dealer email. Once completed, the car can be delivered, and the Warranty claim can be submitted later without penalty since the car has been repaired.To All Mazda Dealers: Failure to properly perform any recall repair is a direct violation of Paragraph 14(F) of the Dealer Agreement and can cause one or more of the following: Mechanical breakdown or failure, crash or injury, Dealership penalties/fines by Mazda and CARB/EPA, increased liability risk for the dealership, Missed Recall penalties, loss of customer trust and a poor Customer Experience. Concern Outline: All vehicles can be repaired immediately upon receipt of this Mazda Dealer announcement by following the repair and warranty claiming procedures housed in Mazda Global Service Support (MGSS). On certain subject vehicles, during normal driving, a temporary decrease in insulation resistance may be detected, which could be mistakenly judged as an electric leakage, causing the hybrid system warning light to turn on and the leakage detection message to be displayed. The DTC P0AA6:00 may be stored in memory. In such a condition, once the vehicle power is switched off, it may become impossible to restart the vehicle due to fail-safe mode activation. Repair Outline: Reprogram the PCM with the Mazda Modular Diagnostic System (M-MDS), using Mazda Diagnostic and Repair Software (MDARS). The DTC code that may appear is P0AA6:00 - High voltage insulation malfunction: Decrease in vehicle insulation resistance. The software update will re-calibrate electrical leakage detection criteria and allow vehicle re-start. Legitimate electrical leakage faults can still be detected and store DTC P0AA6:00. If DTC P0AA6:00 - High voltage insulation malfunction: Decrease in vehicle insulation resistance is still present after repair of the 7325C Recall, please diagnose the issue using the Workshop Manual or search for a current Technical Service Bulletin.

NHTSA · 제조사 공지11016385연식 2025원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통전장NA

공지

7325C - EMISSION RECALL - 2024-2025 CX-90 AND 2025 CX-70 PHEV ONLY - HYBRID SYSTEM WARNING LIGHT MAY TURN ON. Mazda Motor Corporation has decided to conduct an Emission Recall on certain 2024-2025 CX-90 and 2025 CX-70 PHEV vehicles. Please see the description, model, year, and VIN range below for all vehicles in this campaign. There are 38,812 vehicles affected by this concern in the U.S. and U.S. Territories. Vehicles produced and sold by Mazda Canada Inc. are also included in this campaign and should be repaired if presented to your dealership following Mazda Warranty policy 3.30. STOP DELIVERY OF AFFECTED VEHICLES: MAZDA SALES AND SERVICE TEAMS - ACTION ITEM: There are approximately 5,197 vehicles in stock at U.S. Mazda dealers which must be repaired prior to delivery. All Mazda dealers must quarantine any affected new, used or CPO in-stock vehicles until the repair is completed. The affected dealer inventory list was provided to each District Service Manager with the notification of this dealer email. Once completed, the car can be delivered, and the Warranty claim can be submitted later without penalty since the car has been repaired.To All Mazda Dealers: Failure to properly perform any recall repair is a direct violation of Paragraph 14(F) of the Dealer Agreement and can cause one or more of the following: Mechanical breakdown or failure, crash or injury, Dealership penalties/fines by Mazda and CARB/EPA, increased liability risk for the dealership, Missed Recall penalties, loss of customer trust and a poor Customer Experience. Concern Outline: All vehicles can be repaired immediately upon receipt of this Mazda Dealer announcement by following the repair and warranty claiming procedures housed in Mazda Global Service Support (MGSS). On certain subject vehicles, during normal driving, a temporary decrease in insulation resistance may be detected, which could be mistakenly judged as an electric leakage, causing the hybrid system warning light to turn on and the leakage detection message to be displayed. The DTC P0AA6:00 may be stored in memory. In such a condition, once the vehicle power is switched off, it may become impossible to restart the vehicle due to fail-safe mode activation. Repair Outline: Reprogram the PCM with the Mazda Modular Diagnostic System (M-MDS), using Mazda Diagnostic and Repair Software (MDARS). The DTC code that may appear is P0AA6:00 - High voltage insulation malfunction: Decrease in vehicle insulation resistance. The software update will re-calibrate electrical leakage detection criteria and allow vehicle re-start. Legitimate electrical leakage faults can still be detected and store DTC P0AA6:00. If DTC P0AA6:00 - High voltage insulation malfunction: Decrease in vehicle insulation resistance is still present after repair of the 7325C Recall, please diagnose the issue using the Workshop Manual or search for a current Technical Service Bulletin.

NHTSA · 제조사 공지11016384연식 2025원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통전장NA

공지

Important Note: This Service alert is intended as an early notification for upcoming software releases. Please refer to the latest dealer communications and MGSS for updated information. CX-90 MHEV Battery: Mazda is currently experiencing many backorders on MHEV Batteries (K6Y8-67-ZBXD). The issue causing most of the concerns is a cell imbalance inside the MHEV battery, which sets DTC P0DAB. The repair solution for this concern is to perform the software reflash and replace the battery as required. The cell balancing issue is resolved with a software reflash starting in November of 2023 production and this software update is part of recall 7024J - SAFETY RECALL - MULTIPLE ECU'S REPROGRAMMING. Ensure this recall is completed on every CX-90 that comes into your dealer to prevent possible MHEV cell imbalance. As a reminder, the MHEV battery is warrantied 8 years/80,000 miles to support our customers through the life of their vehicle. In terms of the MHEV Battery back-order status, as a result of significant efforts, including air-shipping hundreds of replacement batteries, we are projecting all current backorders will be filled by the last week of March 2025. CX-90 and CX-70 PHEV Electrical Leakage: Some customers have experienced an electrical leakage fault with DTC P0AA6 resulting in a no start condition after one key-cycle. Mazda has identified a PCM software programming issue that causes this DTC occurrence. Under current PCM logic, when P0AA6 detection occurs, the vehicle is prevented from restarting. The new software will be available in late March to reflash vehicles. This allows vehicles to be restarted if the fault is detected. Should the DTC persist, perform normal MGSS service procedures for electrical leakage diagnosis.

NHTSA · 제조사 공지11016241연식 2025원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통차체NA

공지

Some vehicles may exhibit poor hands-free liftgate operation after a Mazda genuine trailer tow hitch accessory installation. IMPORTANT: When a Mazda genuine trailer tow hitch is installed on a vehicle equipped with hands-free liftgate function, the sensing area is reduced due to the mechanical structure of the hitch. The hands-free liftgates optimal sensing area below the rear bumper is shown in green boxes in the image below. Since the left side of the hitch has a 7-pin connector socket, the right side is the most ideal for hands-free operation. For safety, be extra careful performing the kicking motion around the hitch.

NHTSA · 제조사 공지11016231연식 2025원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

Some vehicles may exhibit a creaking or squeaking noise from the lower control arm at the front suspension when traveling over a bump while turning at low-speed. A stick-slip phenomenon may occur between the stopper rubber (2) and the bracket (3) in the front lower arm (rear) (1). To eliminate this concern: Grease has been applied to the stopper rubber. Dust covers have been installed to the lower arm. The mounting hole size of the lower arm bracket has been modified.

NHTSA · 제조사 공지11016200연식 2024원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통엔진NA

공지

Some customers may experience an inacurrate fuel gauge: Rapid fuel level drop when fuel guage is below 1/4. Distance to empty reading (DTE) is incorrect. DTC P0462:00 (Fuel gauge sender unit system: Low input) may be stored. Engine no start and fuel guage shows vehicle has fuel, but engine starts after adding fuel. This may be caused by a faulty Fuel Gauge Sender Unit (Sub).

NHTSA · 제조사 공지11014998연식 2025원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
이전 →

출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).