무료 열람 · 무료 계정으로 기여Anticars(2000)의 후속

Mercedes-BenzMercedes-Benz E 클래스 W214

2023– · 결함 1건 · 1개 시장

이 파일은 Mercedes-Benz E 클래스 W214의 알려진 결함을 커뮤니티가 출처와 함께 정리한 것입니다. 누구나 무료로 읽을 수 있고, 무료 계정으로 기여할 수 있습니다. 신뢰할 수 있는 기여자가 충분히 검증하면 결함에 인증 마크가 붙습니다.

소유자들이 이 차의 electrical system 문제를 자주 보고하지만(16건) 아직 아무도 원인을 설명하지 않았습니다. 알고 계신가요?항목 작성

가장 심각한 결함

전체 보기 (1) →
m
보통전장NA

Electrical system: problems reported by owners

16 owners in the United States reported problems with the electrical system of this car to NHTSA (model years 2024–2026), typically at around 21,000 miles.

✓ 공식 데이터에 대한 Mecafile 분석2024–2026원문(영어)으로 표시 중 · 번역 대기자세히 보기 →

최신 공식 리콜

전체 보기 (43) →
리콜심각전장EU

Des boulons de raccordement au sol spécifiques de 12v et 48v peuvent avoir été fixés avec un couple…

Des boulons de raccordement au sol spécifiques de 12v et 48v peuvent avoir été fixés avec un couple incorrect, ce qui peut conduire à ce que les faisceaux de câblage ne soient pas correctement fixés. en conséquence, la résistance électrique aux points de connexion pourrait augmenter. la température peut donc augmenter dans cette zone, entraînant un incendie.

Safety Gate · EU · RappelConso · 프랑스2026년 8월 27일sr/02875/25연식 2024원문(프랑스어)으로 표시 중 · 번역 대기자세히 보기 →
리콜심각실내NA

Label

Issue: On certain vehicles, the wrong airbag warning labels may have been installed on the driver and passenger sun visors. As a result, the vehicles don't meet the requirements of Canadian regulations. Safety Risk: The airbag warning labels provide information about airbags and child restraint safety recommendations. Not following these recommendations could create an increased risk of injury. Corrective Actions: Mercedes-Benz will notify owners by mail and advise you to take your vehicle to a dealership to inspect and, if necessary, replace the driver and passenger sun visors.

캐나다 교통부2026년 7월 31일2026376연식 2026원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜경미기타JP

その他(その他)

事故自動緊急通報装置の車載通信モジュールにおいて、製造工程が不適切なため、基板内のダイオードに亀裂が生じると共に警告メッセージが表示されることがある。そのため、緊急通報時にコールセンターの音声が聞こえず、双方向通信ができないため、保安基準に適合しないおそれがある。

국토교통성 · 일본2026년 5월 14일1241780연식 2024–2025원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →

최신 기술 서비스 공지

전체 보기 (244) →
공지경미차체NA

공지

Complaint Wheezing noises/squeaking noises from the front shock absorbers when passing over surface undulations and rough road. Noise MUST match those heard in the attached videos. Cause Wheezing noises: Flow noises of the damper oil Squeaking noises: From the mechanical rubber valve in the dividing piston Remedy In case of complaints, the front shock absorbers must be replaced. If shocks have been replaced and noise persists, please open a TIPS case to the Body, Chassis, Entertainment inbox.

NHTSA · 제조사 공지11039086연식 2024–2027원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

Complaint Cracking noises on load change from rear axle (can be heard from wheel side). See attached reference video Cause Micromovement between the rear halfshaft (axle shaft) and wheel bearing mounting surface. Remedy To verify, a test drive and thorough NVH diagnosis must be performed in order to verify the root cause of the noise. If the axle shafts have been identified as the source of the noise, perform the following steps: 1. Verify that rear axle side shaft part number A 214 350 44 06 are currently installed on both sides. If an earlier part number is installed, replace the affected side shaft(s) with A 214 350 44 06. (Before installation, proceed with remaining steps) 2. Clean the contact surfaces of the side shafts and wheel bearings (remove any existing Molykote coating and wear debris). 3. Install one antiknock washer per side (A000 990 86 62) 4. Reinstall both side shafts 5. Perform road test and verify noise is no longer present Note: Application of Molykote coating is no longer required.

NHTSA · 제조사 공지11038946연식 2025–2027원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

Complaint Diverse functional limitations in the vehicle in combination with various warning and fault messages in the instrument cluster display. Cause Communication timeouts mean that communication errors may occur in the onboard electrical system, which can result in various fault messages being displayed in the instrument cluster. This could be down to delayed feedback from the drivetrain control unit (N127) (CPC) to other control units networked to the CAN bus. Information: Only valid for vehicles through production period 10/2025. Not valid for vehicles with control unit CDCC (N125, central controller charging and driving) It may not be possible to attribute any communication errors stored in the control units on the CAN bus to a specific cause In rare instances, there may be a brief activation of the yellow warning lamp for engine diagnosis or there may be a sporadic delay with the start enable. There may not be any specific fault codes present that indicate a specific component. Example image: Fault messages in instrument cluster: The reason for this could be down to delayed feedback from the control unit CPC3 to other control units networked on the CAN bus. Remedy Do not replace any components!!! ******************************************************************************************************* 1. Connect charger (see AR54.10P1127WT). Note: An adequate voltage from the onboard electrical system battery must be guaranteed for the entire duration of the work procedure. Otherwise, the control units could be damaged if an undervoltage occurs. Information: Observe the operating instructions of the charger. Information: Use the charger to ensure an adequate voltage (at least 12.5 V) from the onboard electrical system battery. 2. Connect diagnostic system (see AD00.00P200006FR). Note: Always use the latest XENTRY Diagnostics software release. Information: Strict compliance with the operation steps in XENTRY Diagnostics is absolutely essential. 3. Select control unit N127 (CPC) via the direct link using XENTRY Diagnosis. Information: To do so, select the following menu items: Control units view Drive systems N127 "Drivetrain" control unit (CPC) 4. Update software for control unit N127 (CPC) (see AR54.21P001401Y). Info: To do so, select the following menu items: Adaptations Control unit update Update control unit software. Information: You are then automatically guided through the steps "Update of control unit software" and "SCN coding". Always observe the following operation steps at all times 5. Disconnect diagnostic device from vehicle (see AD00.00P200006FR). 6. Disconnect charger from vehicle (see AR54.10P1127WT).

NHTSA · 제조사 공지11038925연식 2024–2026원문(영어)으로 표시 중 · 번역 대기자세히 보기 →

출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).