무료 열람 · 무료 계정으로 기여Anticars(2000)의 후속

Mercedes-BenzMercedes-Benz E 클래스

1985– · 8 세대 · 결함 92건 · 7개 시장
세대

Mercedes-Benz E 클래스의 모든 세대를 한곳에: 결함, 리콜, 서비스 회보, 토론. 세대를 선택해 범위를 좁히세요.

가장 심각한 결함

전체 보기 (92) →
m

Electrical system: problems reported by owners

244 owners in the United States reported problems with the electrical system of this car to NHTSA (model years 1994–2001), typically at around 112,000 miles. Most often named: wiring:front underhood (24%), wiring (16%). Reported consequences: 3 crashes, 24 fires, 9 injuries.

✓ 공식 데이터에 대한 Mecafile 분석1994–2001원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
m

Airbags: problems reported by owners

76 owners in the United States reported problems with the airbags of this car to NHTSA (model years 1995–2001), typically at around 120,000 miles. Most often named: frontal (26%). Reported consequences: 24 crashes, 4 fires, 29 injuries.

✓ 공식 데이터에 대한 Mecafile 분석1995–2001원문(영어)으로 표시 중 · 번역 대기자세히 보기 →

최신 공식 리콜

전체 보기 (588) →
E 클래스 V213 · 2016–2023
리콜보통변속기UK

SRPC2603 - Drive Shaft Joint

Mercedes-Benz AG has determined that on certain 4MATIC E-Class (213 platform) S-Class Coupé (217 platform) S-Class (222 platform) E-Class Coupe/Convertible (238 platform) GLC (253 platform) and CLS (257 platform) vehicles increased wear of the universal joint on the drive shaft might occur.

DVSA · 영국2026년 9월 21일R/2026/148연식 2019원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
E 클래스 W212 · 2008–2016E 클래스 V213 · 2016–2023
리콜심각서스펜션EU

Motorrijtuigen en aanhangwagens - stuurinrichting

De drie aluminium schroeven waarmee de power-pack aan de stuurinrichting is bevestigd, kunnen door blootstelling aan water en strooizout roesten.

rdw2026년 8월 28일MGP230033연식 2010–2016원문(네덜란드어)으로 표시 중 · 번역 대기자세히 보기 →
E 클래스 W214 · 2023–
리콜심각전장EU

Des boulons de raccordement au sol spécifiques de 12v et 48v peuvent avoir été fixés avec un couple…

Des boulons de raccordement au sol spécifiques de 12v et 48v peuvent avoir été fixés avec un couple incorrect, ce qui peut conduire à ce que les faisceaux de câblage ne soient pas correctement fixés. en conséquence, la résistance électrique aux points de connexion pourrait augmenter. la température peut donc augmenter dans cette zone, entraînant un incendie.

Safety Gate · EU · RappelConso · 프랑스2026년 8월 27일sr/02875/25연식 2024원문(프랑스어)으로 표시 중 · 번역 대기자세히 보기 →

최신 기술 서비스 공지

전체 보기 (874) →
E 클래스 W214 · 2023–
공지경미차체NA

공지

Complaint Wheezing noises/squeaking noises from the front shock absorbers when passing over surface undulations and rough road. Noise MUST match those heard in the attached videos. Cause Wheezing noises: Flow noises of the damper oil Squeaking noises: From the mechanical rubber valve in the dividing piston Remedy In case of complaints, the front shock absorbers must be replaced. If shocks have been replaced and noise persists, please open a TIPS case to the Body, Chassis, Entertainment inbox.

NHTSA · 제조사 공지11039086연식 2024–2027원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
E 클래스 W214 · 2023–
공지보통서스펜션NA

공지

Complaint Cracking noises on load change from rear axle (can be heard from wheel side). See attached reference video Cause Micromovement between the rear halfshaft (axle shaft) and wheel bearing mounting surface. Remedy To verify, a test drive and thorough NVH diagnosis must be performed in order to verify the root cause of the noise. If the axle shafts have been identified as the source of the noise, perform the following steps: 1. Verify that rear axle side shaft part number A 214 350 44 06 are currently installed on both sides. If an earlier part number is installed, replace the affected side shaft(s) with A 214 350 44 06. (Before installation, proceed with remaining steps) 2. Clean the contact surfaces of the side shafts and wheel bearings (remove any existing Molykote coating and wear debris). 3. Install one antiknock washer per side (A000 990 86 62) 4. Reinstall both side shafts 5. Perform road test and verify noise is no longer present Note: Application of Molykote coating is no longer required.

NHTSA · 제조사 공지11038946연식 2025–2027원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
E 클래스 V213 · 2016–2023E 클래스 W214 · 2023–
공지보통서스펜션NA

공지

Complaint Diverse functional limitations in the vehicle in combination with various warning and fault messages in the instrument cluster display. Cause Communication timeouts mean that communication errors may occur in the onboard electrical system, which can result in various fault messages being displayed in the instrument cluster. This could be down to delayed feedback from the drivetrain control unit (N127) (CPC) to other control units networked to the CAN bus. Information: Only valid for vehicles through production period 10/2025. Not valid for vehicles with control unit CDCC (N125, central controller charging and driving) It may not be possible to attribute any communication errors stored in the control units on the CAN bus to a specific cause In rare instances, there may be a brief activation of the yellow warning lamp for engine diagnosis or there may be a sporadic delay with the start enable. There may not be any specific fault codes present that indicate a specific component. Example image: Fault messages in instrument cluster: The reason for this could be down to delayed feedback from the control unit CPC3 to other control units networked on the CAN bus. Remedy Do not replace any components!!! ******************************************************************************************************* 1. Connect charger (see AR54.10P1127WT). Note: An adequate voltage from the onboard electrical system battery must be guaranteed for the entire duration of the work procedure. Otherwise, the control units could be damaged if an undervoltage occurs. Information: Observe the operating instructions of the charger. Information: Use the charger to ensure an adequate voltage (at least 12.5 V) from the onboard electrical system battery. 2. Connect diagnostic system (see AD00.00P200006FR). Note: Always use the latest XENTRY Diagnostics software release. Information: Strict compliance with the operation steps in XENTRY Diagnostics is absolutely essential. 3. Select control unit N127 (CPC) via the direct link using XENTRY Diagnosis. Information: To do so, select the following menu items: Control units view Drive systems N127 "Drivetrain" control unit (CPC) 4. Update software for control unit N127 (CPC) (see AR54.21P001401Y). Info: To do so, select the following menu items: Adaptations Control unit update Update control unit software. Information: You are then automatically guided through the steps "Update of control unit software" and "SCN coding". Always observe the following operation steps at all times 5. Disconnect diagnostic device from vehicle (see AD00.00P200006FR). 6. Disconnect charger from vehicle (see AR54.10P1127WT).

NHTSA · 제조사 공지11038925연식 2023–2026원문(영어)으로 표시 중 · 번역 대기자세히 보기 →

최신 포럼 글

아직 토론이 없습니다.

결함과 토론은 세대별로 정리됩니다. 글을 올리려면 위에서 세대를 선택하세요.

출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0).