자동차 - 차체(좌석)
운전석 시트 레일은 장기간 사용 시 특정 위치에서 균열이 생기기 시작할 수 있습니다.
🔔 무료 계정을 만들고 Nissan 마치 (모든 세대) 이메일 알림 받기
운전석 시트 레일은 장기간 사용 시 특정 위치에서 균열이 생기기 시작할 수 있습니다.
조수석 에어백에 균열이 생길 수 있습니다. 이 경우 에어백의 보호 기능이 저하되어 사고 발생 시 부상 위험이 높아집니다.
The passenger airbag may develop a tear during deployment.
차량 중 기계식 키 점화 시스템이 장착된 일부 차량에서, 점화 스위치 내부의 스프링이 마모되어 파손될 수 있습니다. 이로 인해 주행 중 점화 키가 의도치 않게 ON 위치에서 ACC(액세서리) 위치로 이동할 수 있으며, 이 경우 엔진이 꺼지고 에어백 시스템의 전원이 차단될 수 있습니다. 동력 손실과 조향 및 제동력의 변화는 부상 및/또는 재산 피해를 초래하는 사고의 위험을 높일 수 있습니다. 또한 사고가 발생하더라도 에어백이 작동하지 않을 수 있습니다. 시정 조치: 딜러는 점화 스위치의 로트 번호(lot number)를 점검하고, 해당되는 경우 새 제품으로 교체합니다. 참고: 시정 조치가 完了되기 전까지 차량 소유자는 여분의 열쇠, 키 체인 등 점화 키 링에 달린 모든 물건을 제거할 것을 권장합니다.
The seat belt retractor internal car sensor may not function as intended. In the event of an accident, the retractors could fail to lock and in such circumstances the seatbelt would not restrain the occupant.
Cracks may form in the front wheel hub. The front wheel hub could consequently break leading to the front wheel become detached.
On certain vehicles, a bad connection at the side airbag sensor connector could cause a momentary communication loss from the side airbag sensor to the Airbag Control Unit (ACU). This would put the system in a backup state, lowering the impact threshold required for a side airbag deployment. If a door is being closed with force while the system is in this backup state, this could cause an unintended curtain airbag, seat-mounted side airbag and seat belt pretensioner deployment in a non-warranted (non-impact) situation, which would increase the risk of injury to occupants. Correction: Dealers will install a jumper harness and replace the side airbag sensor with a new one.
The lower pinion needle bearing may have been omitted during manufacture of the steering gear due to insufficient controls in the suppliers manufacturing process. It is possible the pinion may disengage from the steering gear with loss of steering control.
null There is a possibility that the lower pinion needle bearing may have been omitted from the steering system during manufacture. If this is the case, the upper bearing would be overloaded and, if left in this condition, the pinion may disengage causing loss of steering control.
It has been identified that due to the incorrect assembly of the driver airbag inflator. If the vehicle is involved in a collision and the air bag is required to deploy then the gas flow path may have been blocked increasing the internal pressure within the inflator. As a result the driver airbag inflator casing may crack and fragment.
Bij het activeren van de voorste passagiersairbags kan ten gevolge van een te hoge druk van het opblaasmechanisme de behuizing van de airbag losraken.
On certain vehicles, the driver's (frontal) airbag inflator was built with an incorrect part which could cause the inflator to rupture during a deployment. In a crash, this may cause airbag components to separate, which could allow fragments to be propelled toward vehicle occupants, increasing the risk of injury. Correction: Dealers will replace the driver's (frontal) airbag inflator.
null The driver airbag inflator may have been assembled incorrectly. In the event of deployment of the airbag, the gas flow path may be blocked increasing the internal pressure in the inflator. As a result, the driver airbag inflator casing may crack and fragment causing injuries.
ステアリングホイールにおいて、固定ボルトの締め付けが不適切なものがあるため、走行中の振動等により当該固定ボルトが緩んで、ステアリングホイールとステアリングコラムのセレーション勘合部でガタが発生することがある。そのまま使用を続けると、当該セレーション勘合部が摩耗してガタが更に大きくなり、最悪の場合、ハンドル操作ができなくなるおそれがある。
It is possible that the steering wheel mounting bolt may not have been torqued to the correct specification. In addition this torque setting may deteriorate over time as axial tension on the steering wheel boss can be affected by temperature change. The driver will receive warning of the issue by the excessive play/movement in the steering wheel. However should the driver neglect to take notice of this warning it is possible that the steering wheel could detach and affect direction control of the vehicle.
Nissan has identified that the fuel rail pressure sensor of some vehicles may have not been correctly tightened to the fuel rail of the engine and may loosen gradually due to heat and vibration of the engine. If left undetected and the vehicle continues to be driven in this condition in extreme cases fuel leakage may occur.
かじ取装置の中間シャフトにおいて、ピニオンシャフトの挿入が不十分なため、確実に締結されていないものがある。そのため、ピニオンシャフトが徐々に抜け出して、最悪の場合、ハンドル操作ができなくなるおそれがある。
It has been identified that the driver's airbag on some K12 Micras due to incorrect welding of the airbag module may not deploy in the event of a frontal impact. Thus potentially reducing the protection afforded to the vehicle's occupants.
The steering wheel retaining bolt may not have been tightened to the specified torque. If ignored it can potentially lead to a loss of steering control.
The security of the fuel filler hose to tube joint may be insufficient due to clip size and clamping capability. If ignored fuel leakage may occur.
특정 차량에서는 운전석을 상부 레일의 설계 특징과 겹치는 위치에 두지 않아야 합니다. 특정 조건에서는 그 위치가 레일 소재의 응력 한계를 초과할 수 있기 때문입니다.
Le siège du conducteur peut être défectueux, ce qui peut faire en sorte que les ancrages de la ceinture de sécurité ne fonctionnent pas comme prévu, ce qui crée un risque de blessure en cas d’accident.
이슈: 일부 차량에서 변속기를 후진(R)으로 놓을 때 후방 카메라 시스템이 기본 설정으로 돌아가지 않습니다. 운전자가 이전에 카메라 화면을 조정해 두었다면 이로 인해 후방 시야가 줄어들 수 있습니다. 캐나다 규정에서는 카메라가 켜질 때마다 후방 영상이 원래 설정으로 돌아가도록 요구하고 있습니다. 안전 위험: 후방 시야가 줄어들면 사고 위험이 높아질 수 있습니다. 시정 조치: 회사는 소유주에게 우편으로 통지하고, 차량을 딜러에게 가져가 후방 카메라의 소프트웨어를 업데이트하도록 안내할 예정입니다.
車両製作工場の完成検査において、完成検査工程における合否判定が不明確な可能性があるため、道路運送車両の保安基準に関する検査が適切に行われていなかった。
車両製作工場の完成検査において、任命されていない検査員が合否判定を行ったものがあり、安全環境性能法規(保安基準)に関する検査が適切に行われていなかった。
출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).