무료 열람 · 무료 계정으로 기여Anticars(2000)의 후속

Smart 포투

1998–2019 · 3 세대 · 결함 17건 · 2개 시장
세대

기술 서비스 공지(TSB)는 제조사가 알려진 문제에 대해 딜러에게 보내는 수리 지침입니다. 안전 리콜은 아니지만 결함을 확인해 주는 경우가 많습니다.

연식
시장전체NA
포투 III · 2014–2019
공지보통브레이크NA

공지

**고객 불만** 60MPH에서 제동 시 차량 진동이 발생하여 재방문 정비를 받음. 참고: 증상이 타이어나 휠 진동과 유사하더라도, 항상 발생하는지 아니면 제동 시에만 발생하는지에 따라 뚜렷하게 구별되는 경우가 많습니다. **원인** 진동의 원인은 대개 로터 또는 허브/휠 베어링의 과도한 측면 런아웃일 가능성이 높습니다. 그러나 다른 가능한 원인이 있는지 전체 시스템을 함께 점검해야 합니다. 1. 이전 충돌로 인한 손상 2. 회전 부품 없이 차량을 장기간 방치한 경우 3. 휠 베어링/허브의 측면 런아웃 4. 휠 결합면이 과도하게 조여진 경우(WIS 토크 절차를 따르지 않음) 5. 결합면이 과도하게 개조된 경우(도장, 긁힘, 휨 등) **조치 방법** 작업을 수행하기 전에 첨부된 작업 시트 전체를 읽어 보십시오. 작업 후에는 마지막 페이지를 검토하고 그에 따라 작업하십시오. 참고: 이 문서는 사전 승인이 아니며 보증과 관련된 문서도 아닙니다. 진단 목적으로만 사용됩니다. 진행 방법에 대해 의문이 있거나, 작업 시트를 수행했음에도 같은 증상으로 차량이 다시 입고된 경우에는 작업 시트에 나온 측정을 다시 수행한 후, Body, Chassis, and Entertainment 팀에 TIPS 케이스를 등록하십시오.

NHTSA · 제조사 공지11038186연식 2017자동 번역 · 원문: 영어자세히 보기 →
포투 III · 2014–2019
공지보통서스펜션NA

공지

**불만 사항** 조향 시 스티어링 칼럼 부위에서 소음이 발생합니다. 첨부 영상 예시: "MRSMSchleifgerusch_SCCMGrindingNoises. MOV" **원인** 분석 중 **조치** 소음이 스티어링 칼럼의 어느 부위에서 발생하는지 확인하십시오. 소음이 운전석 발밑 하단에서 주로 발생합니까, 아니면 스티어링 칼럼 스위치 모듈(MRSM/SCCM) 부위에서 주로 발생합니까? 소음이 MRSM/SCCM 부위에서 발생하는 경우 다음 사항을 순서대로 점검하십시오. - MRSM/SCCM과 스티어링 휠의 볼트를 풀고, MRSM/SCCM의 위치를 재조정한 후 볼트를 다시 체결하십시오(WIS 참조). MRSM/SCCM에 응력이 걸려 소음이 발생하는 경우가 있습니다. - 소음이 계속 발생하면 소음 불만이 없는 차량의 MRSM/SCCM과 교체하십시오. - 불만이 제기된 MRSM/SCCM을 불만이 없는 차량(기준 차량)에 장착했을 때도 소음이 발생하면 MRSM/SCCM을 교체할 수 있습니다. - 기준 차량의 MRSM/SCCM을 고객 차량에 장착했을 때도 소음이 발생하면 MRSM/SCCM은 원인이 아니므로 교체하지 마십시오. **참고 사항** - MRSM/SCCM을 장착할 때 손상이 발생하지 않도록 주의하십시오. - 소음이 스티어링 휠에서 발생하는 경우(첨부 영상 "LenkradSchleifgerusch_SteeringWheelGrindingNoises.mp4" 참조) LI46.10P077313을 사용하십시오. - 모든 부품은 "직진 위치"에서만 분해 및 장착하십시오(WIS 참조). - 보증 클레임의 "참고" 항목에 이 LI를 반드시 기재하십시오!

NHTSA · 제조사 공지11038183연식 2019자동 번역 · 원문: 영어자세히 보기 →
포투 III · 2014–2019
공지보통서스펜션NA

공지

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

NHTSA · 제조사 공지11035005연식 2017원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
포투 III · 2014–2019
공지보통변속기NA

공지

Complaint There are several types of complaint about noises or poor windshield wiper wiping performance: A: Wiper blades squeaking, chattering, shuddering B: The windshield is not wiped completely (streaking) C: During the downward movement water is pulled back onto the windshield from the A-pillar (Figure 1) D: After windshield cleaning, water keeps spraying onto the windshield for several wipe cycles (Figure 2) A1: The windshield and wiper blades are contaminated with residues from car washing facilities, identifiable by the water beading. The resulting differences in the friction values between the wiper blades and the windshield can excite the wiper blades to vibrate. Note: It is mostly wax residue from the washer system, but also water-repellent nano-particle coating for paint and/or silicone-based washer fluid, that could cause this problem. A partially dry windshield also has different friction values, which can likewise result in squeaking of the wiper blades A2: The wiper blades are worn by mechanical damage (wiper lip damaged by ice or insect debris, or deformed by long periods of disuse). A3: Incorrect angle of incidence of the wiper arms to the windshield. Because of this, the rubber lip of the wiper blade may not flip over at the reversal point. Cause B: B1: Wax/ dirt residues on the windshield B2: Wiper blades deformed or worn B3: Downforce of wiper arm not OK (Figure 3) Cause C: Water is pulled back onto the windshield by the differential pressure created as the wiper arm moves downwards. Cause D: Washer water collects in the fastening of the wiper blade and is blown onto the windshield by the airstream over several wipe cycles. Note and supporting information: Wiper blades are wear parts which, even when "not used" for long periods (kept in park position), may become permanently deformed and damaged. Further stresses on the rubber wiper blade arise due to various environmental influences which progressively change the effectiveness of the rubber wiper blade and accelerate the aging process. Due to the natural aging process and wear, the wiper blades should be replaced twice a year, preferably in Spring and Fall (see operator's manual). Remedy Remedy A: A1: Cleaning entire windshield with A 000 986 40 71. A2: Checking water's flow behavior after windshield has been cleaned (see Video 1). If, after cleaning, there are still areas with water beading, then the cleaning process must be carried out again until a rejection reaction is no longer present. Note: On the vehicle in the video (Video 1), water still beads on the bottom left of the windshield. The windshield is still not properly clean, even though it appears to be clean. The windshield is only properly clean when there are no more areas on the windshield where water beads. A3: Replace wiper blades with genuine wiper blades. Important: Only exchange wiper blades if windshield no longer has water-repellent areas Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. Remedy B: B1: Clean windshield with intensive cleaner A 000 986 40 71. Important: Do not clean the wiper blades otherwise the graphite coating will be damaged. B2: Replace wiper blades with genuine wiper blades Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. B3: Check the wiper arm for excessive resistance in the bearing. Restore mobility or replace wiper arm if necessary. Remedy C: Problem inherent in design for which there is no technical remedy. Exception: X204 up to 02/2014. In these vehicles, it is possible to install the design configuration of vehicles as of 02/2014. This includes wiper arms (styled arms) with improved behavior in this respect. It is also necessary to replace the wiper blades because the styled arms feature a Top Lock connection (previously Side Lock).

NHTSA · 제조사 공지11032875연식 2017원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
포투 III · 2014–2019
공지보통차체NA

공지

Complaint Headlamp, front fog lamp leaky or fogged. Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system LI82.10-P-078302 Closed ventilation system LI82.10-P-078304

NHTSA · 제조사 공지11031580연식 2017원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
포투 III · 2014–2019
공지보통서스펜션NA

공지

Complaint Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts

NHTSA · 제조사 공지11019018연식 2017원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
포투 III · 2014–2019
공지보통차체NA

공지

Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged headlamp in the following way: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent, then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: External damage to the headlamp does not present a warranty or goodwill case. 1. Clear fogged/condensed LED headlamps and LED rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). 7. If the condensation has disappeared, nothing else has to be done. Note: If defrosting has been performed, you can skip the first step. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. All vents have to be sealed with sealing compound and the existing diaphragm with the stamp (picture 3 [3]). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged (picture 6). If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation. If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. If the pressure test is not passed, the headlamp is leaky. If the cause cannot be rectified, the headlamp must be replaced. Note: If the headlamp is replaced, no dry packs may be installed on the new replacement headlamp. AR82.10-P-5455WT was created for the pressure test. This AR can be used as a reference manual for all closed headlamps. In the event of an open headlamp system, the vent ducts must be sealed before the pressure test.

NHTSA · 제조사 공지11017500연식 2017원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
포투 III · 2014–2019
공지보통차체NA

공지

Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Remedy NOTE: If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for damage. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078896 The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions.

NHTSA · 제조사 공지11017496연식 2017원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
포투 III · 2014–2019
공지보통엔진NA

공지

Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.

NHTSA · 제조사 공지11009122연식 2017원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
포투 III · 2014–2019
공지보통차체NA

공지

Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system

NHTSA · 제조사 공지11007974연식 2017원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
포투 III · 2014–2019
공지보통차체NA

공지

Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304

NHTSA · 제조사 공지11007753연식 2017원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
포투 III · 2014–2019
공지보통차체NA

공지

Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).

NHTSA · 제조사 공지11005294연식 2017원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
포투 III · 2014–2019
공지보통서스펜션NA

공지

Noises in the steering column area when steering. Under analysis. Check which area of the steering column the noises occur in. Do the noises tend to occur at the bottom in the driver footwell or do they tend to occur in the area of the steering column switch module (MRSM/SCCM)? If the noises occur in the area of the MRSM/SCCM, work through the following points: - Loosen screws of the MRSM/SCCM and steering wheel, re-align the MRSM/SCCM, and re-fasten the screws (see WIS). Sometimes there is stress at the MRSM/SCCM and noises occur. - If noises continue to occur, swap the MRSM/SCCM into a vehicle without any (noise) complaints. - If the noises occur with the MRSM/SCCM complained about when it is in the vehicle without a complaint (donor vehicle), the MRSM/SCCM can be replaced. - If noises also occur in the customer vehicle with the MRSM/SCCM from the reference vehicle, the MRSM/SCCM is not the cause and must not be replaced. Notes: - When installing the MRSM/SCCM, make sure that no damage occurs! - Only disassemble and mount all component parts in the "straight-ahead position" (see also WIS). - Please refer to this LI in the "Notes" section of the warranty claim!

NHTSA · 제조사 공지10249495연식 2019원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
포투 III · 2014–2019
공지보통서스펜션NA

공지

The steering wheel generates grinding noises between the steering wheel and steering column switch module during steering maneuvers See example file in the attachments area: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises.mp4 The plastic cover on the back of the steering wheel is not positioned correctly and may therefore rub against the steering column switch module Please use the following noise files for the damaged part analysis: 1. Grinding noise | pot. cause: steering wheel | see attachment: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises. mp4 2. Creaking/cracking noise | pot. cause: steering column switch module | see attachment: MRSM-Schleifgerusch_ SCCM-GrindingNoises.MOV If the noise is due to the steering column switch module, please use LI46.10-P-077314. Check for grinding areas on the steering wheel: Please check the covers on the rear for protrusion and, if necessary, remount. 1. Mask off openings on back of steering wheel with adhesive tape 1. Mark the back of the steering wheel with colored chalk (see Picture 1) 2. Mount steering wheel on steering column switch module and turn the steering wheel from left lock to right lock ten times. 3. The chalk will now have disappeared in the areas where there is rubbing (see Picture 2) Warning: Ensure that no cables and visible areas of the steering wheel are damaged. The abrasive excess material on the back of the steering wheel must be carefully removed with a Dremel tool. Tip: You will need to remove approx. 0.1 mm to 0.3 mm of material (example: Picture 3) Make sure that none of the ground-off material gets into the steering wheel. After removing the material, clean the entire back of the steering wheel with a 1% soap solution.

NHTSA · 제조사 공지10249482연식 2019원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
포투 III · 2014–2019
공지보통서스펜션NA

공지

Installation position of suspension springs at rear axle

NHTSA · 제조사 공지10136106연식 2017원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
포투 III · 2014–2019
공지보통브레이크NA

공지

Brake pedal/carpet seal does not fit properly

NHTSA · 제조사 공지10136015연식 2017원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
포투 III · 2014–2019
공지보통변속기NA

공지

Slight oil leakage at single stage transmission

NHTSA · 제조사 공지10135830연식 2014원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
포투 III · 2014–2019
공지보통서스펜션NA

공지

Creaking, grating or grunting noise while steering audible in the steering gear area. The noise can be transferred through the steering gear into the interior. The noise occurs, in particular, at high temperatures, e.g. in the summer.

NHTSA · 제조사 공지10167004연식 2017원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
포투 III · 2014–2019
공지보통서스펜션NA

공지

Creaking, grating or grunting noise when steering

NHTSA · 제조사 공지10135956원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
포투 III · 2014–2019
공지보통실내NA

공지

The airbag indicator lamp in the instrument cluster remains on.

NHTSA · 제조사 공지10135947원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
포투 III · 2014–2019
공지경미차체NA

공지

**고객 불만:** 도어 내 스피커 부근에서 덜컹거리는 소음이 발생함. **원인:** 분석 중. **조치:** 원인을 좁히기 위해 먼저 도어 트림을 분리하십시오. 도어 트림을 분리한 상태에서도 소음이 계속 발생하면 스피커 쪽으로 진단을 계속 진행하고, 필요한 경우 유용한 동영상을 첨부하여 TIPS 케이스를 생성하십시오. **참고:** 보증 클레임에서 이 문서를 참조하고, 진단이 완료되면 문제를 일으키는 부품에 따라 손상 코드를 선택하십시오. 도어 트림을 분리했을 때 소음이 멈추면 LI72.10P067691에 따라 진행하십시오. **정보:** 이 경우 보증 클레임에서 스피커에 대한 손상 코드를 사용하지 마십시오!

NHTSA · 제조사 공지11038217연식 2017자동 번역 · 원문: 영어자세히 보기 →
포투 III · 2014–2019
공지경미차체NA

공지

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

NHTSA · 제조사 공지11036101연식 2017원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
포투 III · 2014–2019
공지경미전장NA

공지

Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) vehicles listed below, an activation of the Malfunction Indicator Lamp (MIL) may occur due to sporadic jamming of the fuel tank ventilation valve. As a result, we have decided to extend the warranty on the fuel tank ventilation valve from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 10 years/120,000 miles. This extended warranty applies to the aforementioned condition that necessitates the servicing and/or replacement of the fuel tank ventilation valve under the standard warranty terms and conditions. The extended warranty is applicable to the following vehicles:

NHTSA · 제조사 공지11031818연식 2017원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
포투 III · 2014–2019
공지경미전장NA

공지

In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (MBUSA) hereby notifies you of additional benefits regarding your vehicle ownership. What is the concern? MBUSA has determined that on certain Model Year 2016-2017 Smart fortwo (453 platform) vehicles, the secondary air injection system combination valve may not close completely under certain climate conditions due to condensation in the exhaust system. An open combination valve could lead to an activation of a Malfunction Indicator Lamp (MIL), which could cause the vehicle to fail a state smog inspection. What is the outcome? MBUSA is extending the coverage for the combination valve of the secondary air injection system from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years / 150,000 miles (whichever occurs first), which applies to the vehicle regardless of ownership. Any repairs under this warranty extension must be performed by an authorized Mercedes-Benz dealership. Your preferred authorized Mercedes-Benz dealer will perform a diagnosis to determine if the secondary air injection system combination valve is malfunctioning. If diagnosis confirms that your vehicle has the issue, the repair will be performed at no cost to you. This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet.

NHTSA · 제조사 공지11031814연식 2016–2017원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
포투 III · 2014–2019
공지경미차체NA

공지

In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA (MBUSA) is extending the coverage for the change-over valve on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 10 years / 120,000 miles (whichever occurs first), and applies to the vehicle regardless of ownership. Why the warranty extension? On certain Model Year 2016-2017 smart vehicles, the change-over valve which is responsible for the operation of the heating shut-off valve within the coolant circuit, could corrode internally due to water intrusion. The internal corrosion might then prevent proper operation of the heating shut-off valve. Any repairs under this warranty extension must be performed by an authorized Mercedes-Benz smart dealership. If your preferred authorized Mercedes-Benz smart dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be performed at no cost to you. This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet.

NHTSA · 제조사 공지11031811연식 2016–2017원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
이전 →

출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).