Leitura livre · conta gratuita para contribuirSucessor do Anticars (2000)

Audi R8

2006–2024 · 1 defeitos documentados · 3 mercados

Os boletins técnicos (TSB) são instruções de reparação que os fabricantes enviam aos concessionários sobre problemas conhecidos. Não são recalls de segurança, mas muitas vezes confirmam um defeito.

Ano do modelo
MercadoTodosNA
BoletimCríticoMotorNA

Boletim

Supersedes Technical Service Bulletin Group 01 number 12-57 dated October 29, 2012. Noises/inconsistent engine operation after cold start during the catalyst heating phase. The customer may interpret this engine roughness as misfiring. To comply with the legal requirements on exhaust gas emissions according to the LEV-1 and LEV-2 standards, a high exhaust gas quality must be ensured. The necessary catalyst only operates at a temperature over 300C (572F). To achieve this, the catalyst is heated up. The catalyst heating phase is achieved by a late ignition angles and by introducing additional fresh air to the exhaust valves (secondary air system). Late ignition angles make sure that the exhaust gas from the cylinders has a higher temperature. This exhaust gas includes fuel that is un-burnt, and was deliberately injected into great quantities. The secondary air system adds fresh air to the exhaust gas as it leaves the cylinder and the extra fuel is burnt. As a result, the temperatures of the exhaust gas and of the catalyst increase quickly. The afterburning in the exhaust manifold before the catalyst changes the sound characteristic of the engine. This heating-up of the catalyst, including afterburning, is normal and has no effect on the service life of the engine. During this catalyst heating phase, the engine has increased idle speed, may have increased vibrations, and has a different sound characteristic. Depending on conditions, the time of the catalyst heating phase varies.

NHTSA · boletim do fabricante10123969Anos-modelo 2011–2012Exibido no inglês original · tradução pendenteVer detalhes →
BoletimCríticoMotorNA

Boletim

Supersedes Technical Service Bulletin Group 01 number 12-51 dated July 18, 2012. Noises/inconsistent engine operation after cold start during the catalyst heating phase. The customer may interpret this engine roughness as misfiring. To comply with the legal requirements on exhaust gas emissions according to the LEV-1 and LEV-2 standards, a high exhaust gas quality must be ensured. The necessary catalyst only operates at a temperature over 300C (572F). To achieve this, the catalyst is heated up. The catalyst heating phase is achieved by a late ignition angles and by introducing additional fresh air to the exhaust valves (secondary air system). Late ignition angles make sure that the exhaust gas from the cylinders has a higher temperature. This exhaust gas includes fuel that is un-burnt, and was deliberately injected into great quantities. The secondary air system adds fresh air to the exhaust gas as it leaves the cylinder and the extra fuel is burnt. As a result, the temperature of the exhaust gas and of the catalyst increases quickly. The afterburning in the exhaust manifold before catalyst changes the sound characteristic of the engine. This heating-up of the catalyst, including afterburning, is normal and has no effect on the service life of the engine. During this catalyst heating phase the engine has increased idle speed, may have increased vibrations, and a different sound characteristic. Depending on conditions the time of the catalyst heating phase varies.

NHTSA · boletim do fabricante10122803Anos-modelo 2011–2012Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

This bulletin provides information for all gasoline engines when the MIL is on; DTC P240700 is stored - Fuel leak detection pump.

NHTSA · boletim do fabricante11039214Anos-modelo 2023Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

This bulletin provides information when the fuel tank cap seal is leaking; DTC P044200, P045600 and/ or P00EF00 in stored in the ECM.

NHTSA · boletim do fabricante11034668Anos-modelo 2023Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

This bulletin provides information regarding UV leak additive for finding oil leaks.

NHTSA · boletim do fabricante11028398Anos-modelo 2012Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

This bulletin provides information when the fuel tank cap seal is leaking; DTC P044200, P045600 and/ or P00EF00 in stored in the ECM.

NHTSA · boletim do fabricante11025354Anos-modelo 2023Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

This TSB provides information when the fuel tank cap seal is leaking, DTC P044200, P045600, and/or P00EF00 stored in ECM.

NHTSA · boletim do fabricante11022688Anos-modelo 2023Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

This bulleitn provides information regarding UV Leak additive for finding oil leaks.

NHTSA · boletim do fabricante11022633Anos-modelo 2012Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

Esta Solução de Serviço Pendente (PSS) solicita que os técnicos registrem uma entrada no banco de dados de PSS nos casos em que a MIL esteja acesa, Avaliar circuito da bomba de detecção de vazamento, DTC240700.

NHTSA · boletim do fabricante11009316Anos-modelo 2023Traduzido automaticamente · original: inglêsVer detalhes →
BoletimModeradoMotorNA

Boletim

This Pending Service Solution (PSS) requests that technicians enter a PSS record in instances where DTC P240700 Evap leak detection pump circuit is stored.

NHTSA · boletim do fabricante11005851Anos-modelo 2023Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

This Pending Service Solution (PSS) requests that technicians enter a PSS record in instances where DTC P240700 Evap leak detection pump circuit is stored.

NHTSA · boletim do fabricante11002215Anos-modelo 2023Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

This Pending Service Solution (PSS) requests that technicians enter a PSS record in instances where DTC P240700 Evap leak detection pump circuit is stored.

NHTSA · boletim do fabricante11002115Anos-modelo 2023Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

This Pending Service Solution (PSS) requests that technicians enter a record in the PSS Database in instances where the MIL is on and DTC P240700 is stored; Evap leak detection pump circuit.

NHTSA · boletim do fabricante10253248Anos-modelo 2023Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

This bulletin contains instructions for an oil leak that is due to excessive sealant used in a previous repair.

NHTSA · boletim do fabricante10153121Anos-modelo 2012Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

On-Hoist Inspection Section: Removed "Perform a coolant reservoir cap pressure test via ELSA -> Enter VIN # -> Repair manual Engine -> 4-Cylinder Direct Injection 1.8L; 2.0L 4V TFSI Engine (Generation III) -> 19 Cooling System -> Coolant System/Coolant -> Cooling System, Checking for Leaks -> Pressure Relief Valve in Cap, Checking. Only the procedure ?Pressure Relief Valve in Cap, Checking? should be performed in the document Cooling System, Checking for Leaks

NHTSA · boletim do fabricante10120803Anos-modelo 2017Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

Supersedes Technical Service Bulletin Group 10 number 13-10 dated September 5, 2013. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these metal debris pieces are not removed prior to the installation and operation of the replacement engine, they could be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.

NHTSA · boletim do fabricante10119945Anos-modelo 2012Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

Supersedes Technical Service Bulletin Group 24 number 12-27 dated April 23, 2012. MIL is illuminated. Irregular engine performance. R8 Intake Air Hose leaking.

NHTSA · boletim do fabricante10124951Anos-modelo 2011–2012Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

A small amount of dry or crusted coolant is seen on the coolant pump housing. The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. The dry coolant marks are normal.

NHTSA · boletim do fabricante10124868Anos-modelo 2012Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

Supersedes Technical Service Bulletin Group 10 number 10-02 dated September 14, 2010. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the vehicle's engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these pieces are not removed prior to the installation and operation of the replacement engine, the pieces may be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.

NHTSA · boletim do fabricante10121324Anos-modelo 2012Exibido no inglês original · tradução pendenteVer detalhes →
BoletimLeveMotorNA

Boletim

This bulletin provides a statement regarding the bottleneck of supply for VW approved oil types VW 504.00 and VW 507.00.

NHTSA · boletim do fabricante11035854Anos-modelo 2012Exibido no inglês original · tradução pendenteVer detalhes →
BoletimLeveMotorNA

Boletim

This bulletin provides information when DTC B105A1A, B103E25 is stored in 0017; fuel tank level implausible.

NHTSA · boletim do fabricante11035829Anos-modelo 2023Exibido no inglês original · tradução pendenteVer detalhes →
BoletimLeveMotorNA

Boletim

This bulletin provides information when DTC B105A1A, B103E25 is stored in 0017; fuel tank level implausible.

NHTSA · boletim do fabricante11035828Anos-modelo 2023Exibido no inglês original · tradução pendenteVer detalhes →
BoletimLeveMotorNA

Boletim

This bulletin provides informaiton when the engine is not running smoothly, misfiring.

NHTSA · boletim do fabricante11034728Anos-modelo 2012Exibido no inglês original · tradução pendenteVer detalhes →
BoletimLeveMotorNA

Boletim

This bulletin provides information when there is increased oil consumption; >0.5ltr/1000 km.

NHTSA · boletim do fabricante11034657Anos-modelo 2023Exibido no inglês original · tradução pendenteVer detalhes →
BoletimLeveMotorNA

Boletim

This bulletin provides information when there is increased oil consumption; >0.5ltr/1000 km.

NHTSA · boletim do fabricante11027356Anos-modelo 2023Exibido no inglês original · tradução pendenteVer detalhes →
Mais antigos →

Fontes: NHTSA (Estados Unidos, domínio público), Transport Canada (Open Government Licence – Canada), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso e Safety Gate da UE (França, Licence Ouverte 2.0), MLIT (Japão, Licença de Dados Públicos 1.0) e MOLIT (Coreia do Sul, car.go.kr).