Leitura livre · conta gratuita para contribuirSucessor do Anticars (2000)

DodgeDodge Nitro

2006–2011 · 1 gerações · 14 defeitos documentados · 3 mercados
Gerações
Todas as geraçõesNitro2006–2011142255

Os boletins técnicos (TSB) são instruções de reparação que os fabricantes enviam aos concessionários sobre problemas conhecidos. Não são recalls de segurança, mas muitas vezes confirmam um defeito.

GravidadeTodasModerado
Ano do modelo
BoletimModeradoMotorNA

Boletim

Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.

NHTSA · boletim do fabricante10230180Anos-modelo 2012Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.

NHTSA · boletim do fabricante10221594Anos-modelo 2012Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

Descrição da peça: Bloco longo 5.7L Descrição do problema: Este conjunto de bloco longo 5.7L é compatível com aplicações EGR e não EGR. Uma placa de bloqueio EGR (53032739AA) deve ser encomendada ao instalar este conjunto de bloco longo em uma aplicação não EGR. A menos que a placa de bloqueio EGR seja transferida do motor antigo.

NHTSA · boletim do fabricante10229181Anos-modelo 2007Traduzido automaticamente · original: inglêsVer detalhes →
BoletimModeradoMotorNA

Boletim

Service - Four Piece Oil Pan Gasket All Cummins Equipped Vehicles ONLY - The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 Nm [21 ft. lbs.].

NHTSA · boletim do fabricante10223854Anos-modelo 2007Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

Ram/dodge\jeep service campaign: See document search button for owner letter. The engine water pump on certain vehicles may leak coolant. Engine operation with a low coolant level could cause engine damage or low cabin heater output. Csc letter was rec'd. *pe

NHTSA · boletim do fabricante10034071Anos-modelo 2010Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

Chrysler\dodge service campaign: See document search button for owner letter. An incorrect positive crankcase ventilation (pcv) valve may have been installed. An incorrect pcv valve can cause excessive exhaust emissions. Csc letter was received. *pe

NHTSA · boletim do fabricante10028832Anos-modelo 2009Exibido no inglês original · tradução pendenteVer detalhes →

Fontes: NHTSA (Estados Unidos, domínio público), Transport Canada (Open Government Licence – Canada), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso e Safety Gate da UE (França, Licence Ouverte 2.0), MLIT (Japão, Licença de Dados Públicos 1.0) e MOLIT (Coreia do Sul, car.go.kr).