Leitura livre · conta gratuita para contribuirSucessor do Anticars (2000)

DodgeDodge Nitro

2006–2011 · 1 gerações · 14 defeitos documentados · 3 mercados
Gerações
Todas as geraçõesNitro2006–2011142255

Os boletins técnicos (TSB) são instruções de reparação que os fabricantes enviam aos concessionários sobre problemas conhecidos. Não são recalls de segurança, mas muitas vezes confirmam um defeito.

Ano do modelo
BoletimModeradoOutroNA

Boletim

wiTECH Teste de Verificação de Pequeno Vazamento (SLVT) - P0456-VAZAMENTO PEQUENO NO SISTEMA EVAP

NHTSA · boletim do fabricante10236933Anos-modelo 2012Traduzido automaticamente · original: inglêsVer detalhes →
BoletimModeradoMotorNA

Boletim

Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.

NHTSA · boletim do fabricante10230180Anos-modelo 2012Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.

NHTSA · boletim do fabricante10221594Anos-modelo 2012Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

Descrição da peça: Bloco longo 5.7L Descrição do problema: Este conjunto de bloco longo 5.7L é compatível com aplicações EGR e não EGR. Uma placa de bloqueio EGR (53032739AA) deve ser encomendada ao instalar este conjunto de bloco longo em uma aplicação não EGR. A menos que a placa de bloqueio EGR seja transferida do motor antigo.

NHTSA · boletim do fabricante10229181Anos-modelo 2007Traduzido automaticamente · original: inglêsVer detalhes →
BoletimModeradoMotorNA

Boletim

Service - Four Piece Oil Pan Gasket All Cummins Equipped Vehicles ONLY - The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 Nm [21 ft. lbs.].

NHTSA · boletim do fabricante10223854Anos-modelo 2007Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoFreiosNA

Boletim

Adaptive Cruise Control Sensor 1) If you are replacing this part due to the cluster displaying Clean Radar Sensor in Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure

NHTSA · boletim do fabricante10139956Anos-modelo 2012Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

Ram/dodge\jeep service campaign: See document search button for owner letter. The engine water pump on certain vehicles may leak coolant. Engine operation with a low coolant level could cause engine damage or low cabin heater output. Csc letter was rec'd. *pe

NHTSA · boletim do fabricante10034071Anos-modelo 2010Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

Chrysler\dodge service campaign: See document search button for owner letter. An incorrect positive crankcase ventilation (pcv) valve may have been installed. An incorrect pcv valve can cause excessive exhaust emissions. Csc letter was received. *pe

NHTSA · boletim do fabricante10028832Anos-modelo 2009Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoElétricaNA

Boletim

Emissions recall g45--veci label - an incorrect vehicle emission control information (veci) label was installed on about ten thousand vehicles. The originally installed veci label does not display the correct spark plug information. *nj

NHTSA · boletim do fabricante10023661Anos-modelo 2007Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoSuspensãoNA

Boletim

Slight play in steering/stiff/choppy/bumpy ride. *nj

NHTSA · boletim do fabricante10023393Anos-modelo 2007Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoSuspensãoNA

Boletim

Steering angle sensor - not initialized/internal. *kb

NHTSA · boletim do fabricante10021984Anos-modelo 2007Exibido no inglês original · tradução pendenteVer detalhes →
BoletimLeveOutroNA

Boletim

LIFTER, Hydraulic Roller Deactivating (Tucho, Roletes Hidráulicos com Desativação) Por favor, não substitua os tuchos MDS porque o pino de desconexão não está alinhado; isso é normal e não é um defeito.

NHTSA · boletim do fabricante10248517Anos-modelo 2012Traduzido automaticamente · original: inglêsVer detalhes →
BoletimLeveOutroNA

Boletim

LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.

NHTSA · boletim do fabricante10244356Anos-modelo 2012Exibido no inglês original · tradução pendenteVer detalhes →
BoletimLeveOutroNA

Boletim

KEY, Master Ao substituir a chave/FOBIK em um WJ, KJ, TJ ou PT Cruiser, use o número de peça com nível NIC "AC". O nível NIC "AB" não será programado nessas plataformas. Para todas as outras plataformas, se o nível NIC "AB" não for programado no veículo, use a peça com nível NIC "AC" e envie uma garantia de peça.

NHTSA · boletim do fabricante10229256Anos-modelo 2005Traduzido automaticamente · original: inglêsVer detalhes →
BoletimLeveCâmbioNA

Boletim

Customer Satisfaction Notification V51 Reprogram Powertrain Control Module

NHTSA · boletim do fabricante10228020Anos-modelo 2010Exibido no inglês original · tradução pendenteVer detalhes →
BoletimLeveInteriorNA

Boletim

Warranty Bulletin D-20-17 (X85) Active Head Restraint - Select 2012-2013 Jeep Liberty (KK) and 2012 Dodge Nitro (KA) (Rev. A)

NHTSA · boletim do fabricante10224064Anos-modelo 2012Exibido no inglês original · tradução pendenteVer detalhes →
BoletimLeveOutroNA

Boletim

KEY, Master If replacing the key/FOBIK on a WJ, KJ, TJ, or PT Cruiser, use the "AC" NIC level part number. The "AB" NIC level will not program to these platforms. For all other platforms, if the "AB" NIC level will not program to the vehicle, use the "AC" NIC level part and submit a part warranty.

NHTSA · boletim do fabricante10221686Anos-modelo 2005Exibido no inglês original · tradução pendenteVer detalhes →
BoletimLeveCâmbioNA

Boletim

Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders

NHTSA · boletim do fabricante10221150Anos-modelo 2012Exibido no inglês original · tradução pendenteVer detalhes →
BoletimLeveCâmbioNA

Boletim

Kit de Transmissão com Conversor de Torque 1. Todos os veículos Promaster (VF) equipados com 3.6L/62TE. Se os parafusos de fixação do suporte da transmissão à carcaça da transmissão forem removidos durante a manutenção, os parafusos (Número de Peça 06511385A$) são de uso único. Veículos fabricados antes de 23/10/2015 exigem o Kit de Serviço PN 68461214AA, que inclui o Isolador de Transmissão PN 68264483AA, o Suporte de Adaptação 68264479AA e o Kit de Serviço de Parafusos PN 68329056AA. Veículos fabricados em ou após 23/10/2015 exigirão apenas o Kit de Serviço de Parafusos PN 68329056AA. 2. Todos os veículos equipados com 3.6L/62TE. Se o veículo que você está reparando apresentar trinca no flex plate ou falha na bucha da bomba, inspecione e confirme que os dois (2) pinos-guia estão presentes no bloco do motor, os quais alinham a linha de centro da transmissão com a linha de centro do virabrequim, e inspecione visualmente os furos de alinhamento dos pinos-guia na carcaça da transmissão. Se os furos estiverem danificados ou alongados, a transmissão deve ser substituída para evitar danos adicionais à transmissão/flex plate ou à bucha da bomba, devido à impossibilidade de alinhar corretamente o motor com a transmissão durante o reparo. 3. Todos os veículos equipados com 62TE. Se a bucha da bomba estiver riscada ou danificada e os furos de alinhamento dos pinos-guia estiverem em bom estado, substitua o conjunto da bomba em vez de substituir a transmissão completa. 4. Todos os veículos equipados com 62TE. Se o veículo estiver com trepidação/patinagem e apresentar código(s) de MIL P0740 ou P2764, verifique o funcionamento do solenoide do TCC. Se o solenoide do TCC estiver em bom estado, os códigos indicam falha do conversor de torque. Substitua o conversor de torque.

NHTSA · boletim do fabricante10220840Anos-modelo 2005Traduzido automaticamente · original: inglêsVer detalhes →
BoletimLeveInteriorNA

Boletim

Warranty Bulletin D-20-21 (X91) Active Head Restraint - Select 2010 Dodge Journey (JC), Dodge Avenger/Chrysler Sebring (JS), Dodge Nitro (KA), Jeep Liberty (KK), Jeep Compass/Jeep Patriot (MK), Dodge Caliber (PM), Dodge Caravan (RT)

NHTSA · boletim do fabricante10187658Anos-modelo 2010Exibido no inglês original · tradução pendenteVer detalhes →
BoletimLeveInteriorNA

Boletim

Warranty Bulletin D-20-22 (X92) Active Head Restraint - Select 2011 Dodge Journey (JC), Dodge Avenger/Chrysler 200 (JS), Dodge Nitro (KA), Jeep Liberty (KK), Jeep Compass/Jeep Patriot (MK), Dodge Caliber (PM), Dodge Caravan (RT), Dodge Durango (WD), Jeep Grand Cherokee (WK)

NHTSA · boletim do fabricante10187659Anos-modelo 2011Exibido no inglês original · tradução pendenteVer detalhes →
BoletimLeveInteriorNA

Boletim

Warranty Bulletin D-20-17 (X85) Active Head Restraint - Select 2012-2013 Jeep Liberty (KK) and 2012 Dodge Nitro (KA) (Rev. B)

NHTSA · boletim do fabricante10187663Anos-modelo 2012Exibido no inglês original · tradução pendenteVer detalhes →
BoletimLeveInteriorNA

Boletim

Warranty Bulletin D-20-21 (X91) Active Head Restraint - Select 2010 Dodge Journey (JC), Dodge Avenger/Chrysler Sebring (JS), Dodge Nitro (KA), Jeep Liberty (KK), Jeep Compass/Jeep Patriot (MK), Dodge Caliber (PM), Dodge Caravan/Chrysler Town & Country (RT) (Rev. A)

NHTSA · boletim do fabricante10187667Anos-modelo 2010Exibido no inglês original · tradução pendenteVer detalhes →
BoletimLeveInteriorNA

Boletim

Active Head Restraint (AHR) Inadvertent Deployment - X92 Warranty Extension This bulletin involves inspecting the sled bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

NHTSA · boletim do fabricante10187680Anos-modelo 2011Exibido no inglês original · tradução pendenteVer detalhes →
BoletimLeveInteriorNA

Boletim

Active Head Restraint (AHR) Inadvertent Deployment - X91 Warranty Extension This bulletin involves inspecting the sled bracket striker pin and possibly replacinga front seat AHR that has inadvertently deployed. Customers may comment on the following: The AHR is deployed on one or both front seats and will not reset.

NHTSA · boletim do fabricante10187684Anos-modelo 2010Exibido no inglês original · tradução pendenteVer detalhes →
Mais antigos →

Fontes: NHTSA (Estados Unidos, domínio público), Transport Canada (Open Government Licence – Canada), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso e Safety Gate da UE (França, Licence Ouverte 2.0), MLIT (Japão, Licença de Dados Públicos 1.0) e MOLIT (Coreia do Sul, car.go.kr).