Leitura livre · conta gratuita para contribuirSucessor do Anticars (2000)

Mazda MPV

1988–2016 · 3 gerações · 25 defeitos documentados · 4 mercados
Gerações
Ano do modelo
MPV II · 1999–2006
RecallCríticoInteriorNANão conduzir até à reparação

Air bags:Frontal:Passenger side:Inflator module

Mazda North American Operations (Mazda) is recalling certain 2003-2008 Mazda6, 2004-2005 MPV, 2004 RX-8, and 2006-2007 Mazdaspeed6 vehicles. These vehicles had their passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.

NHTSA · Estados Unidos31 de out. de 201919V781000Anos-modelo 2004–2005Exibido no inglês original · tradução pendenteVer detalhes →
MPV II · 1999–2006
RecallCríticoInteriorNANão conduzir até à reparação

Air bags:Frontal:Passenger side:Inflator module

Mazda North America Operations (Mazda) is recalling certain 2005-2006 Mazda MPV vehicles sold, or ever registered, in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. On July 9, 2019 this recall was expanded to include certain 2005-2009 RX-8 vehicles that were previously recalled under 17V-011 but have not yet been repaired. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

NHTSA · Estados Unidos15 de jun. de 201818V404000Anos-modelo 2005–2006Exibido no inglês original · tradução pendenteVer detalhes →
MPV II · 1999–2006
RecallCríticoInteriorNANão conduzir até à reparação

Air bags:Frontal:Passenger side:Inflator module

Mazda North America Operations (Mazda) is recalling certain 2003-2008 Mazda6, 2006-2007 Mazdaspeed6 and 2004 MPV vehicles nationwide. Mazda is also recalling 2005-2006 MPV vehicles in Alabama, Arizona, Arkansas, California, Delaware, the District of Columbia, Florida, Georgia, Hawaii, Illinois, Indiana, Kansas, Kentucky, Louisiana, Maryland, Mississippi, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, South Carolina, Tennessee, Texas, Virginia, West Virginia, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands. On July 9, 2019 this recall was expanded to include certain 2004-2011 RX-8 vehicles that were previously recalled under 16V-354 but have not yet been repaired. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these passenger air bag inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

NHTSA · Estados Unidos15 de jun. de 201818V402000Anos-modelo 2004–2006Exibido no inglês original · tradução pendenteVer detalhes →
MPV II · 1999–2006
RecallCríticoInteriorNA

Airbag

Note: The recall for the 2005-2008 RX-8 models has been superseded by recall <a href="http://wwwapps.tc.gc.ca/Saf-Sec-Sur/7/VRDB-BDRV/search-recherche/detail.aspx?lang=eng&&rn=2018038">2018038 (Mazda Recall 2018A)</a>, and the recall for the 2005-2006 MPV models has been superseded by recall <a href="http://wwwapps.tc.gc.ca/Saf-Sec-Sur/7/VRDB-BDRV/search-recherche/detail.aspx?lang=eng&&rn=2018578">2018578 (Mazda Recall 2618F)</a>. On certain vehicles, long-term exposure to high absolute humidity and temperature, combined with high temperature cycling, could eventually degrade the propellant contained in the passenger frontal airbag inflator. This could cause the airbag to deploy with more force than normal. As a result, if the vehicle were involved in a collision that warrants airbag deployment, fragments could be propelled toward vehicle occupants, and the airbag assembly could be damaged, preventing proper function. These issues could increase the risk of injury. Correction: Dealers will replace the passenger frontal airbag inflator. Additional note: Canadian climate results in the propellant degrading slowly. The recall is being conducted as a precaution to address future risk, and is expected to replace airbag inflators before their function would be affected.

Transport Canada10 de jan. de 20172017011Anos-modelo 2005–2006Exibido no inglês original · tradução pendenteVer detalhes →
MPV II · 1999–2006
RecallCríticoInteriorNA

Airbag

Note: The recall for the 2004 RX-8 model has been superseded by <a href="http://wwwapps.tc.gc.ca/Saf-Sec-Sur/7/VRDB-BDRV/search-recherche/detail.aspx?lang=eng&&rn=2018038">recall 2018-038 (Mazda Recall 2018A)</a>, and the recall for the 2004 MPV model has been superseded by recall <a href="http://wwwapps.tc.gc.ca/Saf-Sec-Sur/7/VRDB-BDRV/search-recherche/detail.aspx?lang=eng&&rn=2018578">2018578 (Mazda Recall 2618F)</a>. On certain vehicles, long-term exposure to high absolute humidity and temperature, combined with high temperature cycling, could eventually degrade the propellant contained in the passenger frontal airbag. This could cause the airbag to deploy with more force than normal. As a result, if the vehicle were involved in a collision that warrants airbag deployment, fragments could be propelled toward vehicle occupants, and the airbag assembly could be damaged, preventing proper function. These issues could increase the risk of injury. Correction: Dealers will replace the airbag inflator. Additional note: Canadian climate results in the propellant degrading slowly. The recall is being conducted as a precaution to address future risk, and is expected to replace airbag inflators before their function would be affected.

Transport Canada26 de mai. de 20162016259Anos-modelo 2004Exibido no inglês original · tradução pendenteVer detalhes →
MPV II · 1999–2006
RecallCríticoInteriorNA

Airbag

On certain vehicles, the front passenger-side airbag was improperly wired and may not provide adequate protection in the event of a crash. Correction: Dealer will install a short wiring harness kit.

Transport Canada19 de fev. de 20042004067Anos-modelo 2004Exibido no inglês original · tradução pendenteVer detalhes →
MPV II · 1999–2006
RecallCríticoInteriorNA

Airbag

On certain vehicle, the airbag warning labels on the sun visors are English only. This does not comply with the requirements of CMVSS 208. Correction: Mazda will mail owners corrected replacement labels and installation instructions.

Transport Canada29 de jul. de 20032003178Anos-modelo 2002–2003Exibido no inglês original · tradução pendenteVer detalhes →
MPV II · 1999–2006
RecallCríticoInteriorNA

Airbag

On certain vehicles, the diffuser may come off the inflator for the passenger air bag during deployment due to improper welding. Under these conditions, expanded gas cannot be supplied to the bag and may not deploy during a frontal crash. Correction: Dealers will replace the passenger side airbag with a correct one.

Transport Canada2 de ago. de 20022002145Anos-modelo 2001Exibido no inglês original · tradução pendenteVer detalhes →
MPV II · 1999–2006
RecallCríticoInteriorJP

Airbag

Em alguns airbags do lado do passageiro, a solda da junta entre o difusor (dispositivo de dispersão) dentro do inflador (dispositivo de inflação) e o corpo do gerador de gás (gerador de gás) é inadequada. Por isso, quando o airbag é acionado, essa junta pode se soltar, fazendo com que o difusor se desprenda. Nesse caso, o gás de expansão não consegue ser fornecido à bolsa, o airbag não se abre e existe o risco de causar lesões excessivas ao ocupante em caso de colisão frontal.

MLIT · Japão1 de ago. de 20021108610Anos-modelo 2000Traduzido automaticamente · original: japonêsVer detalhes →
MPV I · 1988–1999
RecallCríticoInteriorNA

Assentos e Sistemas de Retenção

THE (Takata) BOTÕES PLÁSTICOS DE LIBERAÇÃO DO CINTO DE SEGURANÇA DOS BANCOS DIANTEIROS (ABS) NESTES VEÍCULOS PODEM QUEBRAR, PERMITINDO QUE PEÇAS PLÁSTICAS CAIAM NO CONJUNTO DA FIVELA. SE ISSO ACONTECER, PODE OCORRER UMA CONDIÇÃO DE NÃO TRAVAMENTO, TRAVAMENTO FALSO OU FALHA NA SOLTURA, CRIANDO O RISCO DE LESÕES PESSOAIS EM CASO DE COLISÃO OU FREADA BRUSCA. CORREÇÃO: AS FIVELAS DOS CINTOS DE SEGURANÇA DOS BANCOS DIANTEIROS SERÃO REPARADAS OU SUBSTITUÍDAS, CONFORME NECESSÁRIO.

Transport Canada24 de mai. de 19951995085Anos-modelo 1989–1991Traduzido automaticamente · original: inglêsVer detalhes →
MPV II · 1999–2006
RecallModeradoInteriorJP

Outros (dispositivos de ocupantes)

En vehículos con asiento elevable instalado en el asiento del copiloto, el extremo de la bisagra del reposapiés plegable del asiento elevable queda expuesto; por ello, si se baja el asiento sin usar el reposapiés, el pie u otra parte del cuerpo podría entrar en contacto con dicho extremo de la bisagra y, en el peor de los casos, causar lesiones en el pie u otras partes del cuerpo.

MLIT · Japão25 de nov. de 20102104010Anos-modelo 2000–2002Traduzido automaticamente · original: japonêsVer detalhes →
MPV II · 1999–2006
RecallModeradoInteriorNA

Air bags:Frontal

As a result of an ncap test, certain minivans fail to comply with the requirements of federal motor vehicle safety standard no. 208, "occupant crash protection." the front passenger seat air bag was not correctly wiring.

NHTSA · Estados Unidos17 de fev. de 200404V073000Anos-modelo 2004Exibido no inglês original · tradução pendenteVer detalhes →
MPV II · 1999–2006
RecallModeradoInteriorNA

Air bags:Frontal

On certain passenger vehicles, some of the passenger air bag modules were not properly welded and may not deploy in a collision.

NHTSA · Estados Unidos5 de ago. de 200202V196001Anos-modelo 2001Exibido no inglês original · tradução pendenteVer detalhes →
MPV II · 1999–2006
RecallModeradoInteriorJP

(ファン)ベルト

原動機において、発電機等の補機駆動用ベルトの張力を維持するベルトテンショナーの 取付軸部のカシメが不充分なものがあるため、当該ベルトテンショナーが取付部から脱落 することがあり、補機駆動用ベルトが外れて発電機及びパワーステアリング用油圧ポンプ が作動しなくなり、充電警告灯が点灯するとともに、ハンドル操作力が増大するおそれが ある。

MLIT · Japão20 de dez. de 20012101980Anos-modelo 2000–2001Exibido no japonês original · tradução pendenteVer detalhes →
MPV I · 1988–1999
RecallModeradoInteriorNA

Seat belts:Front:Buckle assembly

The front safety belt buckle release buttons can break. These red plastic release buttons are marked "press." if a button breaks, pieces can fall into the buckle assembly causing the buckle to operate improperly.

NHTSA · Estados Unidos24 de mai. de 199595V103005Anos-modelo 1989–1991Exibido no inglês original · tradução pendenteVer detalhes →
MPV I · 1988–1999
RecallModeradoInteriorNA

Seats And Restraints

These vehicles do not comply with c.M.V.S.S 209 - seat belt assemblies. The centre seat belt attachment hardware brackets for the third seat may not withstand the required tensile load of 6000 lbs or 26.7 kn. Correction: Centre seat belt assembly with bracket will be replaced on affected vehicles.

Transport Canada24 de nov. de 19891989158Anos-modelo 1989Exibido no inglês original · tradução pendenteVer detalhes →
MPV I · 1988–1999
RecallModeradoInteriorNA

Seat belts:Front:Anchorage

The center safety belt attachment hardware brackets for the third seat may not withstand the specified tensile load.

NHTSA · Estados Unidos7 de nov. de 198989V194000Anos-modelo 1989Exibido no inglês original · tradução pendenteVer detalhes →
MPV II · 1999–2006
RecallLeveInteriorNA

Equipment:Other:Labels

Certain minivans fail to comply with the requirements of federal motor vehicle safety standard no. 208, "occupant crash protection." some of these vehicles were produced with air bag warning labels intended for the canadian market. Thus, the labels contain warnings in both english and french. As a result, the area of the english warning is only 16 square centimeters, as opposed to the 30 square centimeters required by the standard.

NHTSA · Estados Unidos9 de mar. de 200404V109000Anos-modelo 2003–2004Exibido no inglês original · tradução pendenteVer detalhes →

Fontes: NHTSA (Estados Unidos, domínio público), Transport Canada (Open Government Licence – Canada), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso e Safety Gate da UE (França, Licence Ouverte 2.0), MLIT (Japão, Licença de Dados Públicos 1.0) e MOLIT (Coreia do Sul, car.go.kr).