Leitura livre · conta gratuita para contribuirSucessor do Anticars (2000)

Mercedes-BenzMercedes-Benz Classe E V213

2016–2023 · 22 defeitos documentados · 3 mercados

Este dossiê reúne os defeitos conhecidos do Mercedes-Benz Classe E V213, escritos e documentados pela comunidade. A leitura é livre; uma conta gratuita permite contribuir. Um defeito recebe o selo quando colaboradores reconhecidos suficientes o validam.

Os proprietários relatam muitas vezes problemas de engine neste carro (93 queixas), mas ninguém explicou ainda a causa. Sabe qual é?Redigir a ficha
Os proprietários relatam muitas vezes problemas de electrical system neste carro (84 queixas), mas ninguém explicou ainda a causa. Sabe qual é?Redigir a ficha

Defeitos mais graves

Ver tudo (22) →
m
CríticoMotorNA

Engine: problems reported by owners

93 owners in the United States reported problems with the engine of this car to NHTSA (model years 2016–2023), typically at around 23,000 miles. Reported consequences: 10 fires, 1 injury.

✓ Análise Mecafile de dados oficiais2016–2023Exibido no inglês original · tradução pendenteVer detalhes →
m
CríticoElétricaNA

Electrical system: problems reported by owners

84 owners in the United States reported problems with the electrical system of this car to NHTSA (model years 2016–2023), typically at around 18,000 miles. Reported consequences: 6 fires, 3 injuries.

✓ Análise Mecafile de dados oficiais2016–2023Exibido no inglês original · tradução pendenteVer detalhes →
m
CríticoInteriorNA

Airbags: problems reported by owners

57 owners in the United States reported problems with the airbags of this car to NHTSA (model years 2016–2019), typically at around 10,000 miles. Reported consequences: 7 crashes, 6 injuries.

✓ Análise Mecafile de dados oficiais2016–2019Exibido no inglês original · tradução pendenteVer detalhes →

Últimos recalls oficiais

Ver tudo (540) →
RecallModeradoCâmbioKR

동력전달장치 기타

공급업체의 생산 공정의 편차로 인해 시간이 지남에 따라 드라이브 샤프트의 유니버셜 조인트가 마모될 수 있으며, 이로 인해 유니버셜 조인트에서 윤활유 손실이 발생하여 유니버셜 조인트가 파손될 수 있음. 그 결과로 트랜스퍼 케이스와 전륜 구동 장치 간의 연결이 끊어져 추진력을 잃을 수 있고 충돌 위험이 증가할 수 있음이 확인됨에 따른 리콜 <대상차량별 생산일자> S 450 4MATIC: 2018.01.25~2019.11.14 S 560 4MATIC: 2019.08.30~2019.09.12 CLS 400 d 4MATIC: 2019.02.25~2019.04.11 S 350 d 4MATIC: 2019.04.09 E 450 4MATIC: 2019.02.05 S 400 d 4MATIC: 2017.12.11

MOLIT · Coreia do Sul30 de set. de 20266389Anos-modelo 2017–2019Exibido no coreano original · tradução pendenteVer detalhes →
RecallModeradoCâmbioUK

SRPC2603 - Drive Shaft Joint

Mercedes-Benz AG has determined that on certain 4MATIC E-Class (213 platform) S-Class Coupé (217 platform) S-Class (222 platform) E-Class Coupe/Convertible (238 platform) GLC (253 platform) and CLS (257 platform) vehicles increased wear of the universal joint on the drive shaft might occur.

DVSA · Reino Unido21 de set. de 2026R/2026/148Anos-modelo 2019Exibido no inglês original · tradução pendenteVer detalhes →
RecallCríticoSuspensãoEU

Motorrijtuigen en aanhangwagens - stuurinrichting

De drie aluminium schroeven waarmee de power-pack aan de stuurinrichting is bevestigd, kunnen door blootstelling aan water en strooizout roesten.

rdw28 de ago. de 2026MGP230033Anos-modelo 2016Exibido no holandês original · tradução pendenteVer detalhes →

Últimos boletins técnicos

Ver tudo (488) →
BoletimModeradoSuspensãoNA

Boletim

Complaint Diverse functional limitations in the vehicle in combination with various warning and fault messages in the instrument cluster display. Cause Communication timeouts mean that communication errors may occur in the onboard electrical system, which can result in various fault messages being displayed in the instrument cluster. This could be down to delayed feedback from the drivetrain control unit (N127) (CPC) to other control units networked to the CAN bus. Information: Only valid for vehicles through production period 10/2025. Not valid for vehicles with control unit CDCC (N125, central controller charging and driving) It may not be possible to attribute any communication errors stored in the control units on the CAN bus to a specific cause In rare instances, there may be a brief activation of the yellow warning lamp for engine diagnosis or there may be a sporadic delay with the start enable. There may not be any specific fault codes present that indicate a specific component. Example image: Fault messages in instrument cluster: The reason for this could be down to delayed feedback from the control unit CPC3 to other control units networked on the CAN bus. Remedy Do not replace any components!!! ******************************************************************************************************* 1. Connect charger (see AR54.10P1127WT). Note: An adequate voltage from the onboard electrical system battery must be guaranteed for the entire duration of the work procedure. Otherwise, the control units could be damaged if an undervoltage occurs. Information: Observe the operating instructions of the charger. Information: Use the charger to ensure an adequate voltage (at least 12.5 V) from the onboard electrical system battery. 2. Connect diagnostic system (see AD00.00P200006FR). Note: Always use the latest XENTRY Diagnostics software release. Information: Strict compliance with the operation steps in XENTRY Diagnostics is absolutely essential. 3. Select control unit N127 (CPC) via the direct link using XENTRY Diagnosis. Information: To do so, select the following menu items: Control units view Drive systems N127 "Drivetrain" control unit (CPC) 4. Update software for control unit N127 (CPC) (see AR54.21P001401Y). Info: To do so, select the following menu items: Adaptations Control unit update Update control unit software. Information: You are then automatically guided through the steps "Update of control unit software" and "SCN coding". Always observe the following operation steps at all times 5. Disconnect diagnostic device from vehicle (see AD00.00P200006FR). 6. Disconnect charger from vehicle (see AR54.10P1127WT).

NHTSA · boletim do fabricante11038925Anos-modelo 2023Exibido no inglês original · tradução pendenteVer detalhes →
BoletimLeveCarroceriaNA

Boletim

**Reclamação:** Ruído metálico/de batida na zona dos altifalantes das portas. **Causa:** Em análise. **Solução:** Para identificar a causa, remova primeiro o revestimento da porta. Se o ruído continuar a ocorrer mesmo com o revestimento da porta removido, prossiga com o diagnóstico na direção do altifalante e, se necessário, crie um caso TIPS com um vídeo informativo em anexo. **Observação:** Consulte este documento na reclamação de garantia e, após concluir o diagnóstico, selecione o código de avaria de acordo com o componente que está a causar o problema. Se o ruído parar quando o revestimento da porta for removido, proceda de acordo com LI72.10P067691. **Informação:** Neste caso, não utilize um código de avaria para os altifalantes na reclamação de garantia!

NHTSA · boletim do fabricante11038217Anos-modelo 2018–2023Traduzido automaticamente · original: inglêsVer detalhes →
BoletimModeradoSuspensãoNA

Boletim

Complaint Slight creaking noises when steering. Cause Noises may come from one or more sleeves of the horn contact plate. Remedy Remove the horn contact plate and check the sleeves for noise; see attached video. If necessary, apply lubricant to the sleeves.

NHTSA · boletim do fabricante11038188Anos-modelo 2017–2023Exibido no inglês original · tradução pendenteVer detalhes →

Fontes: NHTSA (Estados Unidos, domínio público), Transport Canada (Open Government Licence – Canada), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso e Safety Gate da UE (França, Licence Ouverte 2.0), MLIT (Japão, Licença de Dados Públicos 1.0) e MOLIT (Coreia do Sul, car.go.kr).