244 owners in the United States reported problems with the electrical system of this car to NHTSA (model years 1994–2001), typically at around 112,000 miles. Most often named: wiring:front underhood (24%), wiring (16%). Reported consequences: 3 crashes, 24 fires, 9 injuries.
✓ Análise Mecafile de dados oficiais1994–2001Exibido no inglês original · tradução pendenteVer detalhes →
91 owners in the United States reported problems with the engine and cooling of this car to NHTSA (model years 1994–2001), typically at around 77,000 miles. Most often named: engine (25%), engine:gasoline (16%). Reported consequences: 6 crashes, 5 fires, 11 injuries.
✓ Análise Mecafile de dados oficiais1994–2001Exibido no inglês original · tradução pendenteVer detalhes →
76 owners in the United States reported problems with the airbags of this car to NHTSA (model years 1995–2001), typically at around 120,000 miles. Most often named: frontal (26%). Reported consequences: 24 crashes, 4 fires, 29 injuries.
✓ Análise Mecafile de dados oficiais1995–2001Exibido no inglês original · tradução pendenteVer detalhes →
54 owners in the United States reported problems with the transmission and drivetrain of this car to NHTSA (model years 1994–2001), typically at around 90,000 miles. Most often named: automatic transmission (43%). Reported consequences: 3 crashes, 2 fires, 2 injuries.
✓ Análise Mecafile de dados oficiais1994–2001Exibido no inglês original · tradução pendenteVer detalhes →
40 owners in the United States reported problems with the fuel system of this car to NHTSA (model years 1994–2001), typically at around 131,000 miles. Reported consequences: 1 crash, 3 fires.
✓ Análise Mecafile de dados oficiais1994–2001Exibido no inglês original · tradução pendenteVer detalhes →
Des boulons de raccordement au sol spécifiques de 12v et 48v peuvent avoir été fixés avec un couple incorrect, ce qui peut conduire à ce que les faisceaux de câblage ne soient pas correctement fixés. en conséquence, la résistance électrique aux points de connexion pourrait augmenter. la température peut donc augmenter dans cette zone, entraînant un incendie.
Safety Gate · UE · RappelConso · França27 de ago. de 2026sr/02875/25Anos-modelo 2024Exibido no francês original · tradução pendenteVer detalhes →
Complaint Wheezing noises/squeaking noises from the front shock absorbers when passing over surface undulations and rough road. Noise MUST match those heard in the attached videos. Cause Wheezing noises: Flow noises of the damper oil Squeaking noises: From the mechanical rubber valve in the dividing piston Remedy In case of complaints, the front shock absorbers must be replaced. If shocks have been replaced and noise persists, please open a TIPS case to the Body, Chassis, Entertainment inbox.
NHTSA · boletim do fabricante11039086Anos-modelo 2024–2027Exibido no inglês original · tradução pendenteVer detalhes →
Complaint Cracking noises on load change from rear axle (can be heard from wheel side). See attached reference video Cause Micromovement between the rear halfshaft (axle shaft) and wheel bearing mounting surface. Remedy To verify, a test drive and thorough NVH diagnosis must be performed in order to verify the root cause of the noise. If the axle shafts have been identified as the source of the noise, perform the following steps: 1. Verify that rear axle side shaft part number A 214 350 44 06 are currently installed on both sides. If an earlier part number is installed, replace the affected side shaft(s) with A 214 350 44 06. (Before installation, proceed with remaining steps) 2. Clean the contact surfaces of the side shafts and wheel bearings (remove any existing Molykote coating and wear debris). 3. Install one antiknock washer per side (A000 990 86 62) 4. Reinstall both side shafts 5. Perform road test and verify noise is no longer present Note: Application of Molykote coating is no longer required.
NHTSA · boletim do fabricante11038946Anos-modelo 2025–2027Exibido no inglês original · tradução pendenteVer detalhes →
Complaint Diverse functional limitations in the vehicle in combination with various warning and fault messages in the instrument cluster display. Cause Communication timeouts mean that communication errors may occur in the onboard electrical system, which can result in various fault messages being displayed in the instrument cluster. This could be down to delayed feedback from the drivetrain control unit (N127) (CPC) to other control units networked to the CAN bus. Information: Only valid for vehicles through production period 10/2025. Not valid for vehicles with control unit CDCC (N125, central controller charging and driving) It may not be possible to attribute any communication errors stored in the control units on the CAN bus to a specific cause In rare instances, there may be a brief activation of the yellow warning lamp for engine diagnosis or there may be a sporadic delay with the start enable. There may not be any specific fault codes present that indicate a specific component. Example image: Fault messages in instrument cluster: The reason for this could be down to delayed feedback from the control unit CPC3 to other control units networked on the CAN bus. Remedy Do not replace any components!!! ******************************************************************************************************* 1. Connect charger (see AR54.10P1127WT). Note: An adequate voltage from the onboard electrical system battery must be guaranteed for the entire duration of the work procedure. Otherwise, the control units could be damaged if an undervoltage occurs. Information: Observe the operating instructions of the charger. Information: Use the charger to ensure an adequate voltage (at least 12.5 V) from the onboard electrical system battery. 2. Connect diagnostic system (see AD00.00P200006FR). Note: Always use the latest XENTRY Diagnostics software release. Information: Strict compliance with the operation steps in XENTRY Diagnostics is absolutely essential. 3. Select control unit N127 (CPC) via the direct link using XENTRY Diagnosis. Information: To do so, select the following menu items: Control units view Drive systems N127 "Drivetrain" control unit (CPC) 4. Update software for control unit N127 (CPC) (see AR54.21P001401Y). Info: To do so, select the following menu items: Adaptations Control unit update Update control unit software. Information: You are then automatically guided through the steps "Update of control unit software" and "SCN coding". Always observe the following operation steps at all times 5. Disconnect diagnostic device from vehicle (see AD00.00P200006FR). 6. Disconnect charger from vehicle (see AR54.10P1127WT).
NHTSA · boletim do fabricante11038925Anos-modelo 2023–2026Exibido no inglês original · tradução pendenteVer detalhes →
Últimos tópicos do fórum
Nenhuma discussão ainda.
Os defeitos e as discussões são arquivados por geração: escolha uma acima para adicionar o seu.
Fontes: NHTSA (Estados Unidos, domínio público), Transport Canada (Open Government Licence – Canada), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso e Safety Gate da UE (França, Licence Ouverte 2.0).