Leitura livre · conta gratuita para contribuirSucessor do Anticars (2000)

Mini Hatch II

2006–2013 · 18 defeitos documentados · 2 mercados

Os boletins técnicos (TSB) são instruções de reparação que os fabricantes enviam aos concessionários sobre problemas conhecidos. Não são recalls de segurança, mas muitas vezes confirmam um defeito.

Ano do modelo
BoletimModeradoElétricaNA

Boletim

N12 Tank leak diagnostic module (DMTL) pump:limited warranty extension to 10 years/120,000 miles

NHTSA · boletim do fabricante10216756Anos-modelo 2009Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoElétricaNA

Boletim

CLASS ACTION SETTLEMENT: N14 HIGH-PRESSURE FUEL PUMP (HDP) SERVICE BENEFIT CLASS VEHICLES: The MINI vehicle may experience a sudden engine operational failure reduced or loss of power while driving and the malfunction indicator lamp (MIL) may be illuminated along with high-pressure fuel pumprelated faults stored in the Engine Control Module (DME). PROCEDURE Perform the corresponding diagnosis/vehicle test and run the test plans to completion as applicable.

NHTSA · boletim do fabricante10171506Anos-modelo 2009Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

Air Conditioning System Leak Testing. The customer complains of poor or no air conditioning cooling. After further diagnosis, the system is found to be low or empty of a refrigerant charge, but when using an electronic leak detector, no leak can be found. CAUSE: In most cases, an electronic leak detector is not sufficient for identifying small leaks in the system. Electronic leak detectors can give false alarms and can lead to an improper diagnosis of small leaks. A leak cannot be located exactly if accessibility is impaired (in the case of the expansion valve, evaporator or condenser).

NHTSA · boletim do fabricante10162461Anos-modelo 2009Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoFreiosNA

Boletim

Brake Fluid Maintenance Service: 36-Month Interval. The CBS displays the first brake fluid service as a 36-month interval from the date of production, instead of the appropriate 24-month interval. Only vehicles within the specified production range can be serviced and covered by this bulletin. For vehicles outside of the production range specified in this bulletin, refer to the CBS and/or Key Read information for the brake fluid service.

NHTSA · boletim do fabricante10152335Anos-modelo 2011Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoElétricaNA

Boletim

**N12 Tank Leak Diagnostic Module (DMTL) Pump: Extensão da Garantia Limitada para 10 Anos/120.000 Milhas** INFORMAÇÃO Esta versão atualizada deste boletim inclui agora os veículos MINI Cooper ano-modelo 2009 R55, R56 e R57 equipados com motor N12. Para os veículos acima referenciados, a MINI USA, divisão da BMW of North America, LLC ("MINI USA"), está estendendo a garantia limitada da Bomba do Módulo de Diagnóstico de Vazamento do Tanque (DMTL) para: 10 anos/120.000 milhas, conforme determinado pela data original de entrada em serviço do veículo. Componente #1: Esta extensão de garantia limitada "específica para o componente" aplica-se a defeitos de materiais e de mão de obra e está sujeita aos requisitos de elegibilidade do veículo e da cobertura, exclusões e limitações aplicáveis à Garantia Limitada para Automóveis de Passageiros MINI Novos. GRUSB0116-04 Este boletim é um aviso de "extensão de garantia limitada". NÃO é um aviso de Recall ou Ação de Serviço. Não há reparo imediato necessário, a menos que o veículo MINI esteja apresentando atualmente este problema. Mesmo não sendo um Recall, a MINI USA enviará cartas de notificação ao cliente específicas por VIN, em uma liberação faseada. Carta de Notificação ao Cliente - Extensão de Garantia Específica por VIN e Componente Mesmo não sendo um Recall, a MINI USA enviará cartas de notificação ao cliente específicas por VIN, em uma liberação faseada, para os veículos adicionais ano-modelo 2009.

NHTSA · boletim do fabricante10151222Anos-modelo 2009Traduzido automaticamente · original: inglêsVer detalhes →
BoletimModeradoMotorNA

Boletim

During Engine Oil Service a Small O-Ring Is Found in the Oil Filter Housing. No customer complaint has been received. During the scheduled engine oil service, the technician notices a black rubber o-ring lying on the bottom of the engine oil filter housing. The o-ring has been dislodged from the non-return valve inside the engine oil filter housing. No subsequent engine damage occurs from the dislodged o-ring. Engine oil filter housing (1) Rubber o-ring (2) The material dimensions of the rubber o-ring are not satisfactory, allowing it to become dislodged from its installation location.

NHTSA · boletim do fabricante10150347Anos-modelo 2009Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoFreiosNA

Boletim

"Erroneous ""Service due"" Message Though Brake Lining Thickness Sufficient. The CBS data calculated for the remaining distance of the front and/or rear brake pads does not agree with the actual brake pad thickness. The yellow brake lining service due indicator illuminates even though the pad thickness is greater than the minimum wear limit (approximately 3.7 mm); the brake wear sensor has not yet been activated (from a thickness of approx. 4.2 mm). In some cases, the red warning message may already be active. The CBS front/rear brake display is based on a mathematical calculation. Various influences are incorporated into this calculation (for example, vehicle speed, brake pressure, and rotor temperature). Due to changing driving characteristics and/or unfavorable environmental conditions, the calculated remaining distance may differ from actual pad thickness."

NHTSA · boletim do fabricante10150306Anos-modelo 2011Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoFreiosNA

Boletim

Brake Fluid Maintenance Service: 36-Month Interval. The coding in these vehicles has the CBS displaying the first brake fluid service as a 36-month interval from the date of production, instead of the appropriate 24-month interval.

NHTSA · boletim do fabricante10150047Anos-modelo 2011–2012Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoFreiosNA

Boletim

Brake Fluid Maintenance Service: 36-Month Interval. The CBS displays the first brake fluid service as a 36-month interval from the date of production, instead of the appropriate 24-month interval.

NHTSA · boletim do fabricante10150239Anos-modelo 2011–2012Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoFreiosNA

Boletim

"?SI M34 01 13 November 2013 BrakesTechnical Service This Service Information bulletin supersedes SI 34 01 13 dated October 2013. designates changes to this revision SUBJECT Erroneous ""Service due"" Message Though Brake Lining Thickness Sufficient. The CBS data calculated for the remaining distance of the front and/or rear brake pads does not agree with the actual brake pad thickness. The yellow brake lining service due indicator illuminates even though the pad thickness is greater than the minimum wear limit (approximately 3.7 mm); the brake wear sensor has not yet been activated (from a thickness of approx. 4.2 mm). In some cases, the red warning message may already be active. The CBS front/rear brake display is based on a mathematical calculation. Various influences are incorporated into this calculation (for example, vehicle speed, brake pressure, and rotor temperature). Due to changing driving characteristics and/or unfavorable environmental conditions, the calculated remaining distance may differ from actual pad thickness."

NHTSA · boletim do fabricante10150205Anos-modelo 2011Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid.

NHTSA · boletim do fabricante10150087Anos-modelo 2011Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

Engine Oil Leak. The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid.

NHTSA · boletim do fabricante10149500Anos-modelo 2009Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

Service Action: Replace the Coolant Pump. Coolant is leaking from the coolant pump. CAUSE The coolant pump may develop cracks in the plastic housing. These cracks may result in a coolant leak.

NHTSA · boletim do fabricante10149501Anos-modelo 2011Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoSuspensãoNA

Boletim

Service Action: Retrofit John Cooper Works Steering Wheel Gearshift Paddles. A number of these vehicles were inadvertently produced without the standard gearshift paddles. Vehicle option ordering error

NHTSA · boletim do fabricante10149503Anos-modelo 2012Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoOutroNA

Boletim

"White Wear Marks on Canvas Top. Wear marks appear on the convertible top on the left and/or right side C-pillar areas. A For vehicles produced to December 12, 2011 1. Replace the defective canvas convertible top. Refer to ISTA Repair Instruction 54 34 120, ""Replacing soft top fabric."" Note: The following repair steps must be performed before the new top is installed to prevent a repeat repair for wear marks. 2. With the defective canvas cover removed, the current main pillars must be replaced. Refer to ISTA Repair Instruction 54 34 996, ""Replacing left or right main pillar."" 3. The current locking mechanisms and bump stops must be replaced as well. Refer to ISTA Repair Instruction 54 34 196, ""Removing and installing / replacing both stowage locks."" The repair kit* needed is listed below. 7. Reinstall the removed parts in the reverse order of their removal. 8. Operate the top several times to quality check the repair."

NHTSA · boletim do fabricante10149505Anos-modelo 2009Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoFreiosNA

Boletim

Erroneous "Service due" Message Though Brake Lining Thickness Sufficient. The CBS data calculated for the remaining distance of the front and/or rear brake pads does not agree with the actual brake pad thickness. The yellow brake lining service due indicator illuminates even though the pad thickness is greater than the minimum wear limit (approximately 3.7 mm); the brake wear sensor has not yet been activated (from a thickness of approx. 4.2 mm). In some cases, the red warning message may already be active. The CBS front/rear brake display is based on a mathematical calculation. Various influences are incorporated into this calculation (for example, vehicle speed, brake pressure, and rotor temperature). Due to changing driving characteristics and/or unfavorable environmental conditions, the calculated remaining distance may differ from actual pad thickness.

NHTSA · boletim do fabricante10149332Anos-modelo 2009Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

Engine Oil Leak. The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid.

NHTSA · boletim do fabricante10149323Anos-modelo 2011Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoFreiosNA

Boletim

ABS/DSC Control During Light Braking. When driving slowly over uneven road surfaces, there may sometimes be pre-mature ABS application relative to the driving situation with the brake lightly applied. Software in the Dynamic Stability Control unit (DSC)

NHTSA · boletim do fabricante10149331Anos-modelo 2011Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

N16 Engine: Oil Leak from Cylinder Head Sealing Plug. An oil leak can develop at a sealing plug located in the cylinder head, just below the vacuum pump. The sealing plug was not tightened sufficiently during production.

NHTSA · boletim do fabricante10148441Anos-modelo 2009–2012Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

N16 Engine: Oil Leak from Cylinder Head Sealing Plug. An oil leak can develop at a sealing plug located in the cylinder head, just below the vacuum pump. CAUSE The sealing plug was not tightened sufficiently during production.

NHTSA · boletim do fabricante10148391Anos-modelo 2009–2012Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoElétricaNA

Boletim

N16: Falha 274D: a adaptação da mistura é armazenada na DME. Determinadas condições de condução em baixa velocidade e com carga leve, em temperaturas externas mais baixas, podem fazer com que a lâmpada de Service Engine Soon (MIL) se acenda. A seguinte falha seria armazenada na DME: Falha 274D: Adaptação da mistura, faixa de rotação baixa do motor (mistura pobre demais) CAUSA 1. Possíveis vazamentos na admissão/escape ou um componente defeituoso, conforme listado no plano de testes 2. Software da DME desfavorável

NHTSA · boletim do fabricante10148346Anos-modelo 2009–2012Traduzido automaticamente · original: inglêsVer detalhes →
BoletimModeradoFreiosNA

Boletim

Erroneous "Service due" Message Although Brake Lining Thickness is Above Minimum Specification. The yellow "Service Due" warning message lights up in the instrument cluster, even though the brake pad thickness is more than 4.2mm (above the thickness at which the pad sensor intervenes). The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. Software calculation of the brake pad wear model in the DSC.

NHTSA · boletim do fabricante10148349Anos-modelo 2009Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoMotorNA

Boletim

N16 and N18 Engine Oil Leak. The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid.

NHTSA · boletim do fabricante10148293Anos-modelo 2009Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoElétricaNA

Boletim

Service Action: Bluetooth Software (KISU Data) Update. This Service Action is being released to improve customer satisfaction as we strive to be number 1 in the JD Power Initial Quality Survey (IQS). This new KISU software improves the Bluetooth functionality in our vehicles, and it helps to keep us up-to-date with technology innovation. Please implement the Bluetooth Software Update Service Action. This Service Action will be in effect until March 2015. Thank you for your continuous support. Improved KISU data (Customer Initiated Software Update) is now available for installation in these vehicles via the USB port. Improved functionality for COMBOX: z Detailed view of the text messages z Android device connection stability (linked contacts causing BT disconnection) Improved functionality for HU-H: z Reconnection strategy z 3rd Party App Metadata - Album art and song title Note: This Service Action is to be completed only at the dealer. You (dealers) will be receiving vehicles from the VDCs that will require this Service Action to be completed prior to customer delivery.

NHTSA · boletim do fabricante10148212Anos-modelo 2009Exibido no inglês original · tradução pendenteVer detalhes →
BoletimModeradoElétricaNA

Boletim

N16 e N18 Vazamento de Óleo do Motor. O cliente relata que um pequeno vazamento de óleo do motor pode ser visto pela parte inferior do motor. CAUSA A vedação interna da válvula solenoide de controle de volume da bomba de óleo está comprometida, permitindo que o óleo do motor vaze pela válvula solenoide de controle de volume da bomba de óleo. DIAGNÓSTICO A seguir está o procedimento para identificar até onde o óleo do motor migrou dentro do chicote elétrico do motor, quando este problema ocorre, se é que ocorre. O procedimento deve ser seguido com muito cuidado para que o reparo adequado seja identificado. 1. Desconecte a conexão elétrica da válvula solenoide de controle de volume da bomba de óleo conforme as Instruções de Reparo 11 41 519 ""Remoção e instalação ou substituição da válvula solenoide (bomba de óleo do motor)."" Inspecione o conector elétrico; se não for encontrado óleo do motor dentro do conector elétrico, execute o procedimento de reparo da válvula de controle de volume da bomba de óleo. Se for encontrado óleo do motor dentro do conector elétrico, prossiga para a etapa 2 do procedimento de diagnóstico. 2. Remova a tampa do DME e retire os três conectores elétricos do DME. Inspecione os conectores quanto a vestígios de óleo do motor. Se não for encontrado óleo do motor, execute o procedimento de reparo da válvula de controle de volume da bomba de óleo e substitua a seção do motor do chicote elétrico. Consulte o EPC para o número de peça adicional. Se for encontrado óleo do motor no conector do DME, prossiga para a etapa 3. 3. Se for encontrado óleo do motor no conector elétrico do DME, execute o procedimento de reparo da válvula de controle de volume da bomba de óleo, substitua a seção do motor do chicote elétrico e substitua o DME. Consulte o EPC para os números de peça adicionais. Não remova o cárter de óleo do motor. Não substitua a válvula de controle de volume da bomba de óleo. Não substitua a bomba de óleo do motor. REPARO DA VÁLVULA DE CONTROLE DE VOLUME DA BOMBA DE ÓLEO

NHTSA · boletim do fabricante10147956Anos-modelo 2009Traduzido automaticamente · original: inglêsVer detalhes →
Mais antigos →

Fontes: NHTSA (Estados Unidos, domínio público), Transport Canada (Open Government Licence – Canada), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso e Safety Gate da UE (França, Licence Ouverte 2.0), MLIT (Japão, Licença de Dados Públicos 1.0) e MOLIT (Coreia do Sul, car.go.kr).